Report discusses an apparatus that may be used for indicating the formation of fatigue cracks or for following the progress of cracks. Details of the experiment and discussion of the way in which the deflection-crack area relationship may be used to monitor fatigue cracks are included.

"Thirty-nine Z-sections formed from 24S-T aluminum-alloy sheet with the angle of bend between the flanges and the web varying from 5 degrees to 120 degrees were tested as columns. Angles of bend from 30 degrees to 120 degrees had little or no effect on the critical stress or on the average stress at maximum load for local instability of the columns. The lengths of the columns were such that at angles of bend below 30 degrees they failed by Euler buckling" (p. 1).

"An experimental study was made to determine the effect of artificial aging on the tensile properties of alclad 24S-T and 24S-T aluminum-alloy sheet material. The results of the tests show that certain combinations of aging time and temperature cause a marked increase in the yield strength and a small increase in the ultimate strength; these increases are accompanied by a very large decrease in elongation. A curve is presented that shows the maximum yield strengths that can be obtained by aging this material at various combinations of time and temperature" (p. 1).

"The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron" (p. 1).

Bulletin presenting an investigation conducted to determine the effect of countersunk depth on the tightness of two types of machine-countersunk flush rivet. The specimens tested in the study were simple lap joints made by two different riveting methods. The results indicated that roundheaded rivets inserted from the back of the joint with the countersunk heads formed int he driving of the rivets produce tighter joints over a large range of depths than ordinary flush rivets.

Report discussing the effect of inlet-air temperature and cylinder displacement on the charge temperature of an internal-combustion engine at the end of the induction stroke. The experiment to test various types of cylinders and their results on the air temperature and pressure is described.

Report discusses the results of testing of rudder deflection for trim at low speeds in the critical wave-off condition. Depending on the lateral center-of-gravity location on the airplane, the useful load in the wings will change and the ability of the rudder to trim the airplane may be greatly improved.

Results are presented of tests of two specimens tested to study the effect of normal pressure on the critical compressive stress for thin curved sheets. These specimens are designated by their respective rib spacings of 10 inches and 30 inches. The relationship between compressive stress and normal pressure at which buckles disappeared is independent of whether the buckles were made to disappear by increase of normal pressure or decrease of compressive stress. (author).

"In order to determine the critical stresses caused by an outward acting pressure on the upper surface of a wing due to the difference in internal and external pressures, torsional tests were made on two curved-sheet specimens subjected to an outward acting normal pressure. Results show that an outward acting normal pressure appreciable raises the critical shear stress for an unstiffened curved sheet; the absolute increase in critical shear stress is slightly greater for a 30 in. rib spacing than for a 10 in. rib spacing" (p. 1).

Report discusses the "effects of oil introduced into the combustion chamber and of oil-spray piston cooling on the knock-limited performance of aircraft engines" (from Summary). A CFR engine and Allison V-1710 cylinder were used to test the rate of oil consumption, knock, and knock-limited brake mean effective pressure.

Report discusses the results of two tests: "1) aerodynamic tests to determine the effect of the slipstream and thrust from the powered propellers on the lift and trimming-moment characteristics, and 2) hydrodynamic tests to determine the effect of the powered propellers on the range of stable locations of the center of gravity (from Introduction)." Large differences in the stable range between half-thrust and full-thrust conditions were observed. Three effects of power were also involved in the location of the stable range of the center of gravity.

An experimental investigation is being conducted to determine the effect of varying the rivet diameter and pitch on the compressive strength of 24S-T aluminum-alloy panels with longitudinal Z-section stiffeners. The average stress at failing load for each rivet diameter, depth of countersink, and pitch of rivet is provided

"These tests were run to determine the effect that mixing engine exhaust gas with engine intake air has on fuel knock limit, specific fuel consumption, and air consumption." Information about the effect on pressure, air consumption, and fuel consumption is detailed.

Report discusses the effects of compressibility and angle of yaw on the pressure measured by a round-nose and a flat-nose total-pressure tube. The error incurred in the pressure measurements and factors affecting the total-pressure area are described.

Report discussing the results of testing to discover the effects of fuel-vapor loss on F-3 and F-4 knock-limited performance ratings and inspection properties of two aviation fuels, 28-R and 33-R. The percentage of loss at several temperatures, ability to meet Army-Navy fuel specifications, and antiknock rating change is described.

"An electronic circuit for instantaneously indicating angular velocity and acceleration, both positive and negative, of rotating masses is described; readings are taken on electrical indicating meters. The indicator is described in terms of general application. A circuit diagram, calibration curves, and a mathematical analysis of the differentiation circuit are included" (p. 1).

"An analysis was made to show the relative effectiveness of streamline external fuel tanks, a fuel tank in the form of a wing mounted in a biplane position, and auxiliary wing panels attached at the wing tips to increase the span as temporary means for increasing the range of a fighter-type airplane. Figures and charts for the various devices considered show the results of calculations of range, duration of flight, and take-off distance for both land-base and carrier operation. The results indicated that the wing-tip extensions were the most promising of the devices considered" (p. 1).

Report discusses the results of an investigation into the effectiveness of water injection into the combustion end zone of a spark-ignition engine cylinder for the suppression of knock. The injection angle was found to be very important for obtaining maximum results. The results of various angles and amounts of water were examined.

Report discusses a method developed to estimate the quantities of internal coolants required to prevent overheating of the aircraft cylinder when oxygen boost is applied. The formula and calculations related to inlet-air pressure, added oxygen, added water, added nitrogen, and total fluid weight are detailed.

Report presenting an exploration of fatigue stresses of some wrought aluminum alloys, including charts that cover different ranges of stress and number of cycles.

Report discusses an investigation into static pressures in subsonic and supersonic flow over an airplane wing as measured by static-pressure tubes, a static-pressure belt, and orifices flush with the wing surface. The results obtained from the three types of measuring devices and a comparison to theoretical calculations are presented.

Report presenting an investigation to determine whether some characteristic of the boundary layer could be used to provide warning of the increase in stalling speed of a wing caused by ice formations on the leading edge. Results were analyzed by referring the total pressures at the rake to the free-stream total pressure, static pressure at the rake, free-stream static pressure, and static pressure from wind-tip swiveling head.

"The stability characteristics of a glider towed by twin parallel towlines have been studied in the NACA free-flight tunnel. A preliminary theoretical analysis of the stability of a glider restrained from yawing was followed by an experimental investigation of the stability of a model towed from fixed tunnel points in such a way as to simulate tow in level flight. The results of the tests confirm the theoretical analysis and indicate that a pilotless, stable, towed-glider system is possible when twin parallel towcables are used" (p. 1).

Report discusses the results of an investigation to determine the feasibility of using the change in the specific gravity of fuels in aircraft fuel tanks to measure fuel-vaporization loss. Six fuels were tested via fuel-distillation tests and simulated-flight tests. An equation based on the specific gravity of the fuel is also described.