Memorandum presenting the use of the modified slender-body method to predict the lift and moment interference of triangular wing-body combinations adapted to combinations with other than triangular wings. The methods are applied to the prediction of the lit-curve slopes of nearly 100 triangular, rectangular, and trapezoidal wing-body configurations.

Memorandum presenting forces and moments measured at Mach number 1.6 in the 4- by 4-foot supersonic pressure tunnel on bombs of fineness ratios 7.0 and 10.5 in the presence of a swept-wing fighter-bomber airplane configuration for a large number of positions under the fuselage. The results can be used to calculate bomb-drop paths.

Report presenting an investigation at transonic speeds to determine the effects of fences, drooped nose, combination fences and drooped nose, and vortex generators on a 45 degree sweptback wing-fuselage combination. The purpose of undertaking this investigation was due to the pitch-up tendency that results from leading-edge vortex-type flow on thin sweptback wings. The data for each component and their interaction with one another is also provided.

Report presenting testing of models of rocket-motor fins of the ASROC missile for flutter and divergence in the supersonic flutter tunnel for a range of Mach numbers. Results indicate that both divergence of the overhung leading edge and flutter occur within the sea-level operating conditions of the missile at Mach numbers above 1.0. Results regarding the flutter boundary, type of flutter encountered, possible solutions to flutter problems, and possible effects of nondestructive type of flutter are provided.

Report presenting an investigation to determine the longitudinal stability and afterbody pressure characteristics of the TX-14 and TX-16 special weapons at transonic and supersonic speeds. Results regarding dynamic testing and pressure testing are provided.

"Free-flight tests have been made to determine the drag at zero lift of several configurations of a missile having triangular wings and tails. Base-pressure measurements were also obtained for some of the configurations. The results show that increasing the wing thickness ratio from 4 to 6 percent increased the wing drag by about 100 percent at M = 1.3 and by about 30 percent at M = 1.8" (p. 1).

Report presenting a wind-tunnel investigation to explore the possibility of employing boundary-layer suction slots as a means for delaying laminar separation at the leading edge and turbulent separation over the rear portions of the airfoil section at high lift coefficients. Results regarding lift and drag are explored.

From Summary: "A review of the status of the knowledge on turbine-blade cooling and a description of pertinent NACA investigations are presented. The current limitations in performance of uncooled and cooled engines are briefly discussed. Finally, the knowledge available and investigations to increase the knowledge on heat transfer, cooling-flow, and performance characteristics of cooled turbines are discussed."

Report presenting an investigation of the effects of many of the parameters significant to wing flutter on several untwisted rotating models to determine their significance with respect to stall flutter of propeller blades. The parameters included torsional stiffness, section thickness ratio, sweepback, length-chord ratio, section center-of-gravity location, blade taper, Mach number, and fluid density. Results regarding the considerations on method of presentation, experimental data and discussion, some possible applications, and a comparison of experiment with classical-flutter theory are provided.

Report presenting an experimental investigation of the pressure distributions on a hemispherical nose 3.98 inches in diameter, mounted on a cylindrical support, at several Mach and Reynolds numbers. The Reynolds number was based on body diameter and free-stream conditions. Pressure-drag coefficients were calculated and good agreement was obtained with other testing.

Report presenting an investigation of several fuels in a 16-inch ramjet engine during a free-jet investigation of ramjet performance in a wind tunnel. The fuels used were gasoline, kerosene, blend of 50-percent gasoline and 50-percent propylene oxide, blend of 75-percent kerosene and 25-percent propylene oxide, and isopentane. Results regarding ranges of operation, combustion efficiencies, and weight and volume specific fuel consumptions obtained with various fuels.

Report presenting the use of the modified slender-body method to predict the lift and moment interference of triangular wing-body combinations to evaluate combinations with non-triangular wings. The method is applied to the prediction of lift-curve slopes of nearly 100 triangular, rectangular, and trapezoidal wing-body configurations.

A preliminary analytical evaluation of the air and fuel specific-impulse characteristics of hydrogen, a-methylnapthalene, and graphite carbon has been made. Adiabatic constant-pressure combustion flame temperatures for each fuel at several equivalence ratios were calculated for an initial air temperature of 560 degrees R and a pressure of 2 atmospheres.

Report presenting the results of an investigation to determine the drag, static stability, control effectiveness, boundary-layer conditions, and first-order effects of propeller operation on a scale model of a proposed high-submerged-speed submarine with various bridge-fairwater and tail configurations.

Report presenting an investigation to determine the effect of oxygen concentration of the inlet oxygen-nitrogen mixture on the combustion efficiency of a J33 single combustor operating with gaseous propane fuel. Combustion efficiency data were obtained at a variety of combustion-inlet total pressures, fuel flow rates, and inlet oxygen concentrations. Results regarding combustor data, application of fundamental combustion properties to combustor data, application of simplified reaction kinetics equation to combustor data, comparison of liquid and gaseous fuel data, and limitations of correlation parameters.

Report presenting an investigation to determine the aerodynamic characteristics of two three-blade propellers over a range of blade angles and Mach numbers. The thick-blade propeller was more adversely affected by compressibility than the thin-blade propeller, and the maximum efficiency of the thin-blade propeller was higher than the thick-blade propeller.

Report presenting a series of fence installations tested on a swept-wing jet airplane to determine their effects on the longitudinal instability, or "pitch-up", encountered in high-maneuvering flight. Longitudinal-stability measurements were made at a variety of Mach numbers with nine fence configurations that varied in chordwise extent and spanwise position. Results regarding longitudinal stability, flow phenomena, buffeting and wing dropping, drag, and low-speed stalls are provided.

The problem of improving operational reliability of turbojet engines is studied in a series of papers. Failure statistics for this engine are presented, the theory and experimental evidence on how engine failures occur are described, and the methods available for avoiding failure in operation are discussed. The individual papers of the series are Objectives, Failure Statistics, Foreign-Object Damage, Compressor Blades, Combustor Assembly, Nozzle Diaphrams, Turbine Buckets, Turbine Disks, Rolling Contact Bearings, Engine Fuel Controls, and Summary Discussion.

Memorandum presenting the use of the hypersonic similarity rule to correlate pressure distributions and wave drags for minimum-drag nose shapes derived by Von Karman and Newton. The computed results have been confirmed by comparison with available experimental data. Wave-drag results for both the Karman and Newtonian shapes are compared with each other and with results for ocnes and circular-arc tangent ogives.

Report presenting the total-pressure recovery characteristics of three circular internal-compression inlets with translating centerbodies at a range of free-stream Mach numbers. The inlets differed only in the shape of the internal compression contours. Results regarding the maximum pressure recoveries and pressure-recovery characteristics are provided.

Report summarizing research on the strength and creep of aircraft structural elements and components at elevated temperatures. Experimental data for aluminum alloy columns, plates, stiffened panels, and multiweb box beams are presented for temperatures up to 600 degrees Fahrenheit and compared with results predicted from materials data.

Report presenting an investigation at high subsonic speeds to determine the static stability characteristics of a cambered-delta-wing model with wing dihedral angles of 20 degrees and 50 degrees. Results regarding the longitudinal characteristics and lateral characteristics are provided.

Report presenting an investigation conducted by means of preflight and flight tests to determine the performance of a 50-percent-magnesium 50-percent JP-4 slurry fuel in a twin-engine ramjet test vehicle. Data were obtained over a range of Mach numbers. Although a successful flight test was carried out, the performance obtained from preflight testing was below theoretical values.

Report presenting the heat transfer and pressures on the lifting surfaces of a 60 degree delta wing with NACA 65A005 profile at angles of attack up to 9 degrees. Results obtained are compared to values obtained from flat-plate theory.