From foreword: "This report is a comprehensive overview study of potential alternative methods for long-term management of high-level radioactive waste...Disposal in terrestrial locations."

From foreword: "This report is a comprehensive overview study of potential alternative methods for long-term management of high-level radioactive waste."

Quarterly progress report on a project to test the radiation effects on metallurgy.

From abstract: "...limited study work was performed on the conceptual design of the proposed fast flux test facility and information was obtained in important areas of supporting technology."

From introduction: "This paper describes a sequence for analyzing the effects of ground water flow on waste transport in natural soils."

From introduction: "In June, 1963, a geophysical research program was conducted at Hanford to determine the feasibility and desirability of using seismic methods in geohydrologic studies. Detection and delineation were desired of seven different geological features that in some sites affect the movement of liquid radioactive wastes discharged to the ground."

The experiments described in this report were performed for two purposes: (1) to find a chemical, or combination of chemicals, that would be effective for inhibiting corrosion of steel in static portions of the Hanford water systems, and (2) as screening tests to select candidate mixtures for further testing to replace sodium dichromate as the inhibitor of aluminum and steel corrosion in the Hanford single-pass reactor cooling water.

From introduction: "...a logical system has been developed to yield rapidly the indexing of a given powder pattern by using an electronic computer."

From introduction: "This document discusses the design, fabrication, assembly, and testing of a second generation shim rod assembly, and testing of a second generation shim rod assembly prototype for use in the Plutonium Recycle Test Reactor."

Abstract: "The mechanical properties of a large number of zirconium alloys have been investigated. These alloys include zirconium-tin and zirconium-tin-uranium. Tensile tests have been run on these alloys at room temperature, 500 F, and 600 F. Hot-hardness data have been obtained from room temperature to 1600 F, with particular emphasis on the hot-rolling range. Creep tests and fatigue tests have been run on a number of zirconium-tin alloys at 500 F."

Abstract: "The mechanical properties of a large number of zirconium alloys have been investigated. These alloys include zirconium-tin and zirconium-tin-uranium. Tensile tests have been run on these alloys at room temperature, 500 F, and 600 F. Hot-hardness data have been obtained from room temperature to 1600 F, with particular emphasis on the hot-rolling range. Creep tests and fatigue tests have been run on a number of zirconium-tin alloys at 500 F."

Introduction: "The tensile properties, hot hardness, impact strength; and corrosion resistance of some arc-melted, iodide zirconium alloys have been determined. The alloys investigated include binary alloys of zirconium containing zero to five per cent tin, binary alloys of zirconium containing zero to 0.14 per cent nitrogen, and ternary alloys of zirconium containing tin and nitrogen, tin and uranium, and uranium and beryllium."

This report explores the production of beta silicon carbide, a low-temperature, cubic modification of cubic silicon carbide. The temperature, heating time, type of starting material, and proportion of starting materials were all varied in order to test yields of beta silicon carbide.

Abstract: "As a possible aid in the selection of ceramic materials for use in the fabrication of high-temperature reactor elements, the reported properties of 23 refractory oxidation-resistance ceramic compounds are tabulated. The thermal stresses and heat throughout capacities for nine of these compounds are estimated for conditions of steady heat flow and uniform heat generation in the temperature range of 1500 to 2500 F. The compounds studied have macroscopic thermal-neutron-absorption cross sections lower than 0.2 per centimeter. Data concerning the high-temperature stability of uranium compounds are tabulated for those with melting points above 2450 F."

Abstract: "The mechanical properties and corrosion resistance of induction-melted, zirconium-tin alloys have been determined. The alloys investigated contained from zero to five per cent tin and up to 0.3% carbon. The zirconium used was United States Bureau of Mines sponge zirconium. The mechanical properties investigated include the tensile, hot-hardness, and impact properties."

The following report discusses the method of rolling uranium rods and strips under various rolling conditions and the roll-separating force measured.

Abstract: "The protection of thorium in hot water was studied. Copper electrocladding on thorium offers promising protection against hot water. The corrosion of thorium in 95 C water was reduced appreciably by a thorium phosphate film. The results of this abbreviated investigation offer a basis for the development of a method of protecting thorium at elevated temperatures in corrosive media."

Abstract: "Thorium tubes were cold drawn from extruded tube stock and also from drilled hot-rolled rod. Total reductions up to approximately 85 per cent were accomplished by conventional tube-drawing methods, without an intermediate anneal. The hard-drawn tubes had high tensile strength, but the ductility, as indicated by flaring and flattening tests, was low."

Report discussing studies on various types of protective coatings for a molybdenum sheet. Procedures, materials, and results of each coating are included.

Abstract:"The creep resistance of various uranium binary alloys was investigated at 1500 and 1800 F in vacuum. Tests were made on alloys of uranium with beryllium, columbium, molybdenum, tantalum, titanium, and zirconium and on molybdenum-UO2 composites. Of the alloys examined, those of the uranium-molybdenum system exhibited the best creep resistance. At 1500 F, creep rates of about 0.005%/hr were produced in uranium-molybdenum alloys by a stress of 2500 psi and, at 1800 F, similar creep rates were obtained in composites of 90 wt % molybdenum-10 wt % UO2 by a stress of 12,000 psi."

Abstract: "The solubility of oxygen in uranyl sulphate solutions and in water at 212, 275, and 325 F, and at oxygen partial pressures up to 1500 psia was investigated. The results are presented in tabular and graphic form. The solubility is proportional to the partial pressure of oxygen. The ratio of solubility in the uranyl sulphate solution to solubility in water at the same temperature and pressure is a function of the concentration of the salt in solution."

Abstract: "The ductility of Type 310 stainless steel T-joints brazed with GE-62 brazing alloy was measured at room temperatures 1200, 1650, and 1800 F. The measure of ductility was taken as the plastic axial strain required to crack braze fillets in T-section tensile specimens. At elevated temperatures, the ductility of as-brazed joints approximated that of the stainless steel, but at room temperature the brazed joints had only one-tenth the ductility of the base metal. Annealing for 16 hr at 1800 F in air was found to triple the room-temperature ductility of the brazed joint."

From introduction: This work is a survey of possible uses of ceramic materials in Hanford-type fuel elements.

From abstract: "Various physical and mechanical properties have been determined for high- and low-carbon base uranium, uranium-chromium, and uranium-zirconium alloys. These data complement those obtained at ANL on the same materials."