Advanced Cuttings Transport Study Quarterly Report: July-October 1999 (open access)

Advanced Cuttings Transport Study Quarterly Report: July-October 1999

This report includes a review of the progress made in ACTF Flow Loop development and research during 90 days pre-award period (May 15-July 14, 1999) and the following three months after the project approval date (July15-October 15, 1999) The report presents information on the following specific subjects; (a) Progress in Advanced Cuttings Transport Facility design and development, (b) Progress report on the research project ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress report on the research project ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress report on the research project ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress report on the research project ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Progress report on the instrumentation tasks (Tasks 11 and 12) (g) Activities towards technology transfer and developing contacts with oil and service company members.
Date: October 15, 1999
Creator: Kuru, Ergun; Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Kane, Gerald; Volk, Len et al.
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Report: July-September 2000 (open access)

Advanced Cuttings Transport Study Quarterly Report: July-September 2000

This is the first quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between July 14, 2000 and September 30, 2000. This report presents information on the following specific tasks: (a) Progress in Advanced Cuttings Transport Facility design and development (Task 2), (b) Progress on research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress on research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress on research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress on research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Initiate research on project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Progress on instrumentation tasks to measure: Cuttings concentration and distribution (Tasks 11), and Foam properties (Task 12), (h) Initiate a comprehensive safety review of all flow-loop components and operational procedures. Since the previous Task 1 has been completed, we will now designate …
Date: October 30, 2000
Creator: Reed, Troy; Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Kane, Gerald; Pickell, Mark et al.
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Report: October-December 2000 (open access)

Advanced Cuttings Transport Study Quarterly Report: October-December 2000

This is the second quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between Oct 1, 2000 and December 31, 2000. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 2: Addition of a foam generation and breaker system), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (d) Research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (e) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (h) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review …
Date: January 30, 2000
Creator: Reed, Troy; Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Kane, Gerald; Pickell, Mark et al.
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Report: October-December 2003 (open access)

Advanced Cuttings Transport Study Quarterly Report: October-December 2003

Final design of the mast was completed (Task 5). The mast is consisting of two welded plate girders, set next to each other, and spaced 14-inches apart. Fabrication of the boom will be completed in two parts solely for ease of transportation. The end pivot connection will be made through a single 2-inch diameter x 4 feet-8 inch long 316 SS bar. During installation, hard piping make-ups using Chiksan joints will connect the annular section and 4-inch return line to allow full movement of the mast from horizontal to vertical. Additionally, flexible hoses and piping will be installed to isolate both towers from piping loads and allow recycling operations respectively. Calibration of the prototype Foam Generator Cell has been completed and experiments are now being conducted. We were able to generate up to 95% quality foam. Work is currently underway to attach the Thermo-Haake RS300 viscometer and install a view port with a microscope to measure foam bubble size and bubble size distribution. Foam rheology tests (Task 13) were carried out to evaluate the rheological properties of the proposed foam formulation. After successful completion of the first foam test, two sets of rheological tests were conducted at different foam flow …
Date: January 31, 2004
Creator: Miska, Stefan; Takach, Nicholas & Ashenayi, Kaveh
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Technical Report: April-June 2002 (open access)

Advanced Cuttings Transport Study Quarterly Technical Report: April-June 2002

This is the fourth quarterly progress report for Year-3 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between April 1, 2002 and June 30, 2002. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Separation System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)''; (c) Research project (Task 9b): ''Study of Foam Flow Behavior Under EPET Conditions''; (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions''; (e) Research on three instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), Foam texture while transporting cuttings. (Task 12), and Viscosity of Foam under EPET (Task 9b); (f) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S); (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number …
Date: July 30, 2002
Creator: Reed, Troy; Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Pickell, Mark; Volk, Len et al.
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Technical Report: April-June 2003 (open access)

Advanced Cuttings Transport Study Quarterly Technical Report: April-June 2003

This Quarter has been divided between running experiments and the installation of the drill-pipe rotation system. In addition, valves and piping were relocated, and three viewports were installed. Detailed design work is proceeding on a system to elevate the drill-string section. Design of the first prototype version of a Foam Generator has been finalized, and fabrication is underway. This will be used to determine the relationship between surface roughness and ''slip'' of foams at solid boundaries. Additional cups and rotors are being machined with different surface roughness. Some experiments on cuttings transport with aerated fluids have been conducted at EPET. Theoretical modeling of cuttings transport with aerated fluids is proceeding. The development of theoretical models to predict frictional pressure losses of flowing foam is in progress. The new board design for instrumentation to measure cuttings concentration is now functioning with an acceptable noise level. The ultrasonic sensors are stable up to 190 F. Static tests with sand in an annulus indicate that the system is able to distinguish between different sand concentrations. Viscometer tests with foam, generated by the Dynamic Test Facility (DTF), are continuing.
Date: July 30, 2003
Creator: Reed, Troy; Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Pickell, Mark; Volk, Len et al.
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Technical Report: April-June 2004 (open access)

Advanced Cuttings Transport Study Quarterly Technical Report: April-June 2004

We have tested the loop elevation system. We raised the mast to approximately 25 to 30 degrees from horizontal. All went well. However, while lowering the mast, it moved laterally a couple of degrees. Upon visual inspection, severe spalling of the concrete on the face of the support pillar, and deformation of the steel support structure was observed. At this time, the facility is ready for testing in the horizontal position. A new air compressor has been received and set in place for the ACTS test loop. A new laboratory has been built near the ACTS test loop Roughened cups and rotors for the viscometer (RS300) were obtained. Rheologies of aqueous foams were measured using three different cup-rotor assemblies that have different surface roughness. The relationship between surface roughness and foam rheology was investigated. Re-calibration of nuclear densitometers has been finished. The re-calibration was also performed with 1% surfactant foam. A new cuttings injection system was installed at the bottom of the injection tower. It replaced the previous injection auger. A mechanistic model for cuttings transport with aerated mud has been developed. Cuttings transport mechanisms with aerated water at various conditions were experimentally investigated. A total of 39 tests were …
Date: July 31, 2004
Creator: Miska, Stefan; Takach, Nicholas & Ashenayi, Kaveh
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Technical Report: January 1999-April 2000 (open access)

Advanced Cuttings Transport Study Quarterly Technical Report: January 1999-April 2000

ACTS flow loop is now operational under elevated pressure and temperature. Currently, experiments with water under pressure and temperature are being conducted. Based on the analysis of Fann 70 data, empirical correlations defining the shear stress as a function of temperature, pressure and the shear rate have been developed for Petrobras synthetic drilling fluids. PVT equipment has been modified for testing Synthetic drilling fluids. Initial calibration tests have been conducted by using water. Currently, the base oil of the Petrobras synthetic drilling fluid is being tested. Foam flow experiments have been conducted. Currently, more experiments are being conducted while data are being analyzed to characterize the rheology of the foam. Cuttings transport experiments have been conducted using air, water and cuttings. Preliminary results have shown that it may not be possible to avoid cuttings bed deposition under any practical combination of air and water flow rates. Foam stability analyses have been conducted. Effects of salt and oil concentration on the foam stability have been investigated. A software for controlling the data sampling and data storage during cuttings monitoring process have been developed.
Date: April 30, 2000
Creator: Kuru, Ergun; Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Kane, Gerald; Volk, Len et al.
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Technical Report: January-March 2003 (open access)

Advanced Cuttings Transport Study Quarterly Technical Report: January-March 2003

Experiments on the flow loop are continuing. Improvements to the software for data acquisition are being made as additional experience with three-phase flow is gained. Modifications are being made to the Cuttings Injection System in order to improve control and the precision of cuttings injection. The design details for a drill-pipe Rotation System have been completed. A US Patent was filed on October 28, 2002 for a new design for an instrument that can generate a variety of foams under elevated pressures and temperatures and then transfer the test foam to a viscometer for measurements of viscosity. Theoretical analyses of cuttings transport phenomena based on a layered model is under development. Calibrations of two nuclear densitometers have been completed. Baseline tests have been run to determine wall roughness in the 4 different tests sections (i.e. 2-in, 3-in, 4-in pipes and 5.76-in by 3.5-in annulus) of the flow loop. Tests have also been conducted with aerated fluids at EPET conditions. Preliminary experiments on the two candidate aqueous foam formulations were conducted which included rheological tests of the base fluid and foam stability reports. These were conducted after acceptance of the proposal on the Study of Cuttings Transport with Foam Under Elevated …
Date: April 30, 2003
Creator: Reed, Troy; Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Pickell, Mark; Volk, Len et al.
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Technical Report: July-September 2003 (open access)

Advanced Cuttings Transport Study Quarterly Technical Report: July-September 2003

The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static …
Date: September 30, 2003
Creator: Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Yu, Mengjiao; Ahmed, Ramadan; Pickell, Mark et al.
System: The UNT Digital Library
Advanced Cuttings Transport Study Quarterly Technical Report: October-December 2001 (open access)

Advanced Cuttings Transport Study Quarterly Technical Report: October-December 2001

This is the second quarterly progress report for Year 3 of the ACTS project. It includes a review of progress made in: (1) Flow Loop development and (2) research tasks during the period of time between Oct 1, 2001 and Dec. 31, 2001. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Collection System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (e) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (f) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (g) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members.
Date: January 30, 2002
Creator: Reed, Troy; Miska, Stefan; Takach, Nicholas; Ashenayi, Kaveh; Kane, Gerald; Pickell, Mark et al.
System: The UNT Digital Library