The National Ignition Facility (NIF) at the Lawrence Livermore National Laboratory (LLNL) will routinely fire high energy shots (approaching 10 kJ per beamline) through the final optics, located on the target chamber. After a high fluence shot, exceeding 4J/cm2 at 351 nm wavelength, the final optics will be inspected for laser-induced damage. The FODI (Final Optics Damage Inspection) system has been developed for this purpose, with requirements to detect laser-induced damage initiation and to track and size it's the growth to the point at which the optic is removed and the site mitigated. The FODI system is the 'corner stone' of the NIF optic recycle strategy. We will describe the FODI system and discuss the challenges to make optics inspection a routine part of NIF operations.

Driven by beam stability requirements at the NSLS II synchrotron, such that the desired small beam sizes and high brightness are both realized and stable, a comprehensive study has been launched seeking to provide assurances that stability at the nanometer level at critical x-ray beam-lines, is achievable, given the natural and cultural vibration environment at the selected site. The study consists of (a) an extensive investigation of the site to evaluate the existing ground vibration, in terms of amplitude, frequency content and coherence, and (b) of a numerical study of wave propagation and interaction with the infrastructure of the sensitive lines. The paper presents results from both aspects of the study.

Electronic spin-pairing transition of iron in magnesiow{umlt u}stite-(Mg,Fe)O has been recently studied with X-ray emission and M{umlt o}ssbauer spectroscopies under high pressures. While these studies reported a high-spin to low-spin transition of iron to occur at pressures above approximately 50 GPa, the width of the observed transition varies significantly. In particular, Kantor et al. reported that the transition in (Mg0.8,Fe0.2)O occurs over a pressure range of approximately 50 GPa in high-pressure M{umlt o}ssbauer measurements. To account for the discrepancy in the transition pressure, Kantor et al. reanalyzed the X-ray emission spectra by Lin et al. using a simple spectral decomposition method and claimed that X-ray emission measurements are also consistent with a spin crossover of iron at high pressures. Here we show that the proposed fitting method is inadequate to describe the X-ray emission spectrum of the low-spin FeS2 and would give an erroneous satellite peak (K{sub beta}') intensity, leading to an artificial high-spin component and, consequently, to invalid conclusions regarding the width of the pressure-induced transition in magnesiow{umlt u}stite. Furthermore, we compare Kantor's M{umlt o}ssbauer data with other recent high-pressure M{umlt o}ssbauer studies and show that the width of the transition can be simply explained by different experimental conditions …

We report on the first next-to-leading order QCD computation of W + 3-jet production in hadronic collisions including all partonic subprocesses. We compare the results with CDF data from the Tevatron, and find excellent agreement. The renormalization and factorization scale dependence is reduced substantially compared to leading-order calculations. The required one-loop matrix elements are computed using on-shell methods, implemented in a numerical program, BlackHat. We use the SHERPA package to generate the real-emission contributions and to integrate the various contributions over phase space. We use a leading-color (large-N{sub c}) approximation for the virtual part, which we confirm in W + 1,2-jet production to be valid to within three percent. The present calculation demonstrates the utility of on-shell methods for computing next-to-leading-order corrections to processes important to physics analyses at the Large Hadron Collider.

Many applications of modeling spatial dynamic systems focus on a single system and a single process, ignoring the geographic and systemic context of the processes being modeled. A solution to this problem is the coupled modeling of spatial dynamic systems. Coupled modeling is challenging for both technical reasons, as well as conceptual reasons. This paper explores the benefits and challenges to coupling or linking spatial dynamic models, from loose coupling, where information transfer between models is done by hand, to tight coupling, where two (or more) models are merged as one. To illustrate the challenges, a coupled model of Urbanization and Wildfire Risk is presented. This model, called Vesta, was applied to the Santa Barbara, California region (using real geospatial data), where Urbanization and Wildfires occur and recur, respectively. The preliminary results of the model coupling illustrate that coupled modeling can lead to insight into the consequences of processes acting on their own.

In real materials, nonlinear forces cause the frequencies of vibrating atoms to depend on amplitude. As a consequence, a large-amplitude fluctuation on the scale of the atom spacing can develop a frequency that does not resonate with the normal modes, causing energy to become trapped in an intrinsically localized mode (ILM)--also called 'discrete breather' or 'lattice soliton'. As temperature is increased, entropy is expected to stabilize increased concentrations of these random hotspots. This mechanism, which spontaneously concentrates energy, has been observed in analogous systems on a larger scale, but direct sightings at the atomic scale have proved difficult. Two challenges have hampered progress: (1) the need to separate ILMs from modes associated with crystal imperfections, and (2) complications that arise at high temperatures, including feature broadening and multiphonon processes. Here we solve both of these problems by actively creating ILMs at low temperatures in {alpha}-uranium using high-energy inelastic x-ray and neutron scattering. The ILM creation excitation occurs at energies ten times higher than conventional lattice excitations, cleanly separating it from modes associated with crystal imperfections. The discovery of this excitation not only proves the existence of ILMs in uranium but also opens up a new route for finding ILMs in …

Real-time archiving of mixed paper and digital collections presents challenges not encountered in the primarily paper environment. A few recent examples from the archives of the Stanford Linear Accelerator Center highlight obstacles encountered, and attempted and contemplated solutions.

We present the results of our measurements of the electron cloud density in the PEP-II low energy ring (LER) by propagating a TE wave into the beam pipe. By connecting a signal generator to a beam position monitor button we can excite a signal above the vacuum chamber cut-off frequency and measure its propagation through the beam pipe with a spectrum analyzer connected to another button about 50 meters away. The measurement can be performed with different beam conditions and also at different settings of the solenoids used to reduce the build up of electrons. The presence of a modulation in the TE wave transmission, synchronous with the beam revolution frequency, which appear to increase in depth when the solenoids are switched off, seem to be directly correlated to the electron cloud density in the region between the two BPM's. In this paper we present and discuss the measurements taken in the Interaction Region 12 straight of the LER during 2006 and the first part of 2007.

Short-pulse, high-current discharges in vacuum were investigated with the goal to maximize the ion charge state number. In a direct extension of previous work [Appl. Phys. Lett. 92, 041502 (2008)], the role of pulse length, rate of current rise, and current amplitude was studied. For all experimental conditions, the usable (extractable) mean ion charge state could not be pushed beyond 7+. Instead, a maximum of the mean ion charge state (about 6+ to 7+ for most cathode materials) was found for a power of 2-3 MW dissipated in the discharge gap. The maximum is the result of two opposing processes that occur when the power is increased: (i) the formation of higher ion charge states, and (ii) a greater production of neutrals (both metal and non-metal), which reduces the charge state via charge exchange collisions.

Production of a sterile species is studied within an effective model of active-sterile neutrino mixing in a medium in thermal equilibrium. The quantum kinetic equations for the distribution functions and coherences are obtained from two independent methods: the effective action and the quantum master equation. The decoherence time scale for active-sterile oscillations is tau(dec)=2/Gamma(aa), but the evolution of the distribution functions is determined by the two different time scales associated with the damping rates of the quasiparticle modes in the medium: Gamma(1)=Gamma(aa)cos^2theta(m); Gamma(2)=Gamma(aa)sin^2theta(m) where Gamma(aa) is the interaction rate of the active species in the absence of mixing and theta(m) the mixing angle in the medium. These two time scales are widely different away from Mikheyev-Smirnov-Wolfenstein resonances and preclude the kinetic description of active-sterile production in terms of a simple rate equation. We give the complete set of quantum kinetic equations for the active and sterile populations and coherences and discuss in detail the various approximations. A generalization of the active-sterile transition probability in a medium is provided via the quantum master equation. We derive explicitly the usual quantum kinetic equations in terms of the"polarization vector" and show their equivalence to those obtained from the quantum master equation and effective …

Low-k dielectric materials are becoming increasingly interesting as alternative to SiO2 with device geometries shrinking beyond the 65 nm technology node. At elevated temperatures hydrogen migration becomes an important degradation mechanism for conductivity breakdown in semiconductor devices. The possibility of hydrogen release during the fabrication process is, therefore, of great interest in the understanding of device reliability. In this study, various low-k dielectric films were subjected to thermal annealing at temperatures that are generally used for device fabrication. Elastic recoil detection analysis (ERDA) was used to investigate compositional changes and hydrogen redistribution in thin films of plasma-enhanced tetraethylortho-silicate (PETEOS), phosphorus doped silicon glass (PSG), silicon nitride (SiN) and silicon oxynitride (SiON). Except for an initial hydrogen release from the surface region in films of PETEOS and PSG, the results indicate that the elemental composition of the films was stable for at least 2 hours at 450◦C.

The Linac Coherent Light Source (LCLS), currently under design, requires accurate alignment between the electron beam and each undulator's magnetic centerline. A beam finder wire (BFW) instrument has been developed to provide beam location information that is used to move the undulators to their appropriate positions. A BFW instrument is mounted at each of the 33 magnets in the undulator section. Beam detection is achieved by electrons impacting two carbon fiber wires and then sensing the downstream radiation. The wires are mounted vertically and horizontally on a wire card similar to that of a traditional wire scanner instrument. The development of the BFW presents several design challenges due to the need for high accuracy of the wires locations and the need for removal of the wires during actual operation of the LCLS (30 microns repeatability is required for the wire locations). In this paper, we present the technical specification, design criteria, mechanical design, and results from prototype tests for the BFW.

TOPS is providing high-performance, scalable sparse direct solvers, which have had significant impacts on the SciDAC applications, including fusion simulation (CEMM), accelerator modeling (COMPASS), as well as many other mission-critical applications in DOE and elsewhere. Our recent developments have been focusing on new techniques to overcome scalability bottleneck of direct methods, in both time and memory. These include parallelizing symbolic analysis phase and developing linear-complexity sparse factorization methods. The new techniques will make sparse direct methods more widely usable in large 3D simulations on highly-parallel petascale computers.

Electrical resistivity may contribute to progress inunderstanding geothermal systems by imaging the geometry, bounds andcontrolling structures in existing production, and thereby perhapssuggesting new areas for field expansion. To these ends, a dense grid ofmagnetotelluric (MT) stations plus a single line of contiguous bipolearray profiling has been acquired over the east flank of the Cosogeothermal system. Acquiring good quality MT data in producing geothermalsystems is a challenge due to production related electromagnetic (EM)noise and, in the case of Coso, due to proximity of a regional DCintertie power transmission line. To achieve good results, a remotereference completely outside the influence of the dominant source of EMnoise must be established. Experimental results so far indicate thatemplacing a reference site in Amargosa Valley, NV, 65 miles from the DCintertie, isstill insufficient for noise cancellation much of the time.Even though the DC line EM fields are planar at this distance, theyremain coherent with the nonplanar fields in the Coso area hence remotereferencing produces incorrect responses. We have successfully unwrappedand applied MT times series from the permanent observatory at Parkfield,CA, and these appear adequate to suppress the interference of thecultural EM noise. The efficacy of this observatory is confirmed bycomparison to stations taken using an ultra-distant …

The authors present a Dalitz-plot analysis of charmless B{sup {+-}} decays to the final state {pi}{sup {+-}}{pi}{sup {+-}}{pi}{sup {-+}} using a sample of (465 {+-} 5) x 10{sup 6} B{bar B} pairs collected by the BABAR experiment at {radical}s = 10.58 GeV. They measure the branching fractions {Beta}(B{sup {+-}} {yields} {pi}{sup {+-}}{pi}{sup {+-}}{pi}{sup {-+}}) = (15.2 {+-} 0.6 {+-} 1.2 {+-} 0.4) x 10{sup -6}, {Beta}(B{sup {+-}} {yields} {rho}{sup 0}(770){pi}{sup {+-}}) = (8.1 {+-} 0.7 {+-} 1.2{sub -1.1}{sup +0.4}) x 10{sup -6}, {Beta}(B{sup {+-}} {yields} f{sub 2}(1270){pi}{sup {+-}}) = (1.57 {+-} 0.42 {+-} 0.16{sub -0.19}{sup +0.53}) x 10{sup -6}, and {Beta}(B{sup {+-}} {yields} {pi}{sup {+-}}{pi}{sup {+-}}{pi}{sup {-+}} nonresonant) = (5.3 {+-} 0.7 {+-} 0.6{sub -0.5}{sup +1.1}) x 10{sup -6}, where the uncertainties are statistical, systematic, and model-dependent, respectively. Measurements of branching fractions for the modes B{sup {+-}} {yields} {rho}{sup 0}(1450){pi}{sup {+-}} and B{sup {+-}} {yields} f{sub 0}(1370){pi}{sup {+-}} are also presented. They observe no significant direct CP asymmetries for the above modes, and there is no evidence for the decays B{sup {+-}} {yields} f{sub 0}(980){pi}{sup {+-}}, B{sup {+-}} {yields} {chi}{sub c0}{pi}{sup {+-}}, or B{sup {+-}} {yields} {chi}{sub c2}{pi}{sup {+-}}.

In this study, an array of vibration measurements at the undisturbed NSLS II site has been performed in order to establish the 'green-field' vibration environment and its spectral characteristics. The interaction of the green-field vibration environment with the NSLS II accelerator structure and the quantification of the storage ring vibration, both in terms of amplitude and spectral content have been assessed through a state-of-the-art wave propagation and scattering analysis. This paper focuses on the wave propagation and scattering aspect as well as on the filtering effects of accelerator structural parameters.

The Gamma-Ray Large Area Space Telescope (GLAST) is an international and multiagency mission scheduled for launch in the fall 2007. The Large Area Telescope (LAT), the primary instrument of the mission, will survey the high energy sky found to be very dynamic and surprisingly diverse by its predecessor the Energetic Gamma Ray Experiment Telescope (EGRET). GLAST-LAT will have a much improved sensitivity when compared with EGRET and extend the higher energy coverage to {approx} 300 GeV. The instrument is now mounted on the spacecraft and undergoing a suite of pre-flight tests. Data analysis software has been tried out by collaborators in two rounds of 'Data Challenges' using simulated observations including backgrounds. The instrument performance and observational data on selected sources presented here have been obtained through the Data Challenges in the collaborative efforts. There are features in the GLAST-LAT observation possibly unfamiliar to X-ray astronomers: (1) GLAST will operate mostly in the survey mode; (2) the foreground objects (gas, dust, and star-light) become gamma-ray sources; (3) multiple sources will be 'confused' because of the wide point-spread-function. The last two features will pose a challenge for analysis on extended Galactic sources such as supernova remnants and pulsar wind nebulae: multi-wavelength study …

For many rocks of high economic interest such as chalk,diatomite, tight gas sands or coal, nanometer scale resolution is neededto resolve the 3D-pore structure, which controls the flow and trapping offluids in the rocks. Such resolutions cannot be achieved with existingtomographic technologies. A new 3D imaging method, based on serialsectioning and using the Focused Ion Beam (FIB) technology has beendeveloped. FIB allows for the milling of layers as thin as 10 nanometersby using accelerated Ga+ ions to sputter atoms from the sample surface.After each milling step, as a new surface is exposed, a 2D image of thissurface is generated. Next, the 2D images are stacked to reconstruct the3D pore or grain structure. Resolutions as high as 10 nm are achievableusing this technique. A new image processing method uses directmorphological analysis of the pore space to characterize thepetrophysical properties of diverse formations. In addition to estimationof the petrophysical properties (porosity, permeability, relativepermeability and capillary pressures), the method is used for simulationof fluid displacement processes, such as those encountered in variousimproved oil recovery (IOR) approaches. Computed with the new methodcapillary pressure curves are in good agreement with laboratory data. Themethod has also been applied for visualization of the fluid distributionat various saturations …

Light-Front Holography is a remarkable consequence of the correspondence between string theory in AdS space and conformal field theories in physical-space time. It allows string modes {Phi}(z) in the AdS fifth dimension to be precisely mapped to the light-front wavefunctions of hadrons in terms of a specific light-front impact variable {zeta} which measures the separation of the quark and gluonic constituents within the hadron. This mapping was originally obtained by matching the exact expression for electromagnetic current matrix elements in AdS space with the corresponding exact expression for the current matrix element using light-front theory in physical space-time. More recently we have shown that one obtains the identical holographic mapping using matrix elements of the energy-momentum tensor, thus providing an important consistency test and verification of holographic mapping from AdS to physical observables defined on the light-front. The resulting light-front Schrodinger equations predicted from AdS/QCD give a good representation of the observed meson and baryon spectra and give excellent phenomenological predictions for amplitudes such as electromagnetic form factors and decay constants.

Rapid Cycling Synchrotron (RCS) is a key component of Beijing Spallation Neutron Source (BSNS). It accumulates and accelerates protons to design energy of 1.6 GeV, and extracts high energy beam to the target. As a high beam density and high beam power machine, low beam loss is also a basic requirement. An optimal lattice design is essential for the cost and the future operation. The lattice design of BSNS is presented, and the related dynamics issues are discussed. The injection/extraction scheme and the beam collimation system design are introduced.

We present a novel method to characterize the e{sup {+-}} phase space at the IP of the SLAC B-factory, that combines single-beam measurements with a detailed mapping of luminous-region observables. Transverse spot sizes are determined in the two rings with synchrotron-light monitors and extrapolated to the IP using measured lattice functions. The specific luminosity, which is proportional to the inverse product of the overlap IP beam sizes, is continuously monitored using radiative/Bhabha events. The spatial variation of the luminosity and of the transverse-boost distribution of the colliding e{sup {+-}}, are measured using e{sup +}e{sup -} {yields} {mu}{sup +}{mu}{sup -} events reconstructed in the BABAR detector. The combination of these measurements provide constraints on the emittances, horizontal and vertical spot sizes, angular divergences and {beta} functions of both beams at the IP during physics data-taking. Preliminary results of this combined spot-size analysis are confronted with independent measurements of IP {beta}-functions and overlap IP beam sizes at low beam current.

To compensate the large tune spread generated by the beam-beam interactions in the polarized proton (pp) run in the Relativistic Heavy Ion Collider (RHIC), a low energy round Gaussian electron beam or electron lens is proposed to collide head-on with the proton beam. Using a weakstrong beam-beam interaction model, we carry out multiparticle simulations to investigate the effects of head-on beam-beam compensation on the proton beam's lifetime and emittance growth. The simplectic 6-D element-by-element tracking code SixTrack is adopted and modified for this study. The code benchmarking and preliminary simulation results are presented.

An isomeric series of heterocyclic amines related to one found in heated muscle meats was investigated for properties that predict their measured mutagenic potency. Eleven of the 12 possible 2-amino-trimethylimidazopyridine (TMIP) isomers were tested for mutagenic potency in the Ames/Salmonella test with bacterial strain TA98, and resulted in a 600-fold range in potency. Structural, quantum chemical and hydropathic data were calculated on the parent molecules and the corresponding nitrenium ions of all of the tested isomers to establish models for predicting the potency of the unknown isomer. The regression model accounting for the largest fraction of the total variance in mutagenic potency contains four predictor variables: dipole moment, a measure of the gap between amine LUMO and HOMO energies, percent hydrophilic surface, and energy of amine LUMO. The most important determinants of high mutagenic potency in these amines are: (1) a small dipole moment, (2) the combination of b-face ring fusion and N3-methyl group, and (3) a lower calculated energy of the {pi} electron system. Based on predicted potency from the average of five models, the isomer not yet synthesized and tested is expected to have a mutagenic potency of 0.84 revertants/{micro}g in test strain TA98.

The NSLS-II Light Source, which is planned to be built at Brookhaven National Laboratory, is designed for horizontal emittances below 1 nm and will provide users with ultra-bright synchrotron radiation sources. In order to utilize fully the very small emittances and electron beam sizes, submicron stability of the electron orbit in the storage ring needs to be provided. This can only be achieved with high stability beam position monitors (BPM). The research program presently carried is aimed for characterization of commercially available RF BPM receivers and on the development of high stability mechanical supports for BPM modules. The details of the program and preliminary results are presented.