This report is on Electrochemistry for Gordon Conference

We have demonstrated 466mW of 469nm light from a frequency doubled continuous wave fiber laser. The system consisted of a 938nm single frequency laser diode master oscillator, which was amplified in two stages to 5 Watts using cladding pumped Nd{sup 3+} fiber amplifiers and then frequency doubled in a single pass through periodically poled KTP. The 3cm long PPKTP crystal was made by Raicol Crystals Ltd. with a period of 5.9 {micro}m and had a phase match temperature of 47 degrees Centigrade. The beam was focused to a 1/e{sup 2} diameter in the crystal of 29 {micro}m. Overall conversion efficiency was 11% and the results agreed well with standard models. Our 938nm fiber amplifier design minimizes amplified spontaneous emission at 1088nm by employing an optimized core to cladding size ratio. This design allows the 3-level transition to operate at high inversion, thus making it competitive with the 1088nm 4-level transition. We have also carefully chosen the fiber coil diameter to help suppress propagation of wavelengths longer than 938 nm. At 2 Watts, the 938nm laser had an M{sup 2} of 1.1 and good polarization (correctable with a quarter and half wave plate to >10:1).

None

Using the RQMD model, transverse momentum dependence of the anisotropic flow v{sub 2} for {pi}, K, nucleon, {phi}, and {lambda}, are studied for Au + Au collisions at {radical}s{sub NN} = 200 GeV. Both hydrodynamic hadron-mass hiragracy (hhmh) at low p{sub T} region and particle type dependence (baryon versus meson) at the intermediate p{sub T} region are reproduced with the model calculations although the model underpredicted the overall values of v{sub 2} by a factor of 2-3. As expected, when the rescatterings are turned off, all v{sub 2} becomes zero. The failure of the hadronic model in predicting the absolute values of hadron v{sub 2} clearly demonstrate the need of early dense partonic interaction in heavy-ion collisions at RHIC. At the intermediate p{sub T}, the hadron type dependence cold also be explained by the vacume hadronic cross sections within the frame of the model. The measurements of collective motion of hadrons from high-energy nuclear collisions can provide information on the dynamical equation of state information of the system [1, 2, 3]. Specifically, the strange and multi-strange hadron flow results have demonstrated the partonic collectivity [5] and the heavy-flavor flow will test the hypothesis of early thermalization in such collisions [4]. …

A Plesset-type treatment [J. Appl. Phys. 25, 96 (1954)] is used to assess the effects of contiguous density gradients at an accelerating spherical classical interface on Rayleigh-Taylor and Bell-Plesset perturbation growth. Analytic expressions are obtained that describe enhanced Rayleigh-Taylor instability growth from contiguous density gradients aligned with the acceleration and which increase the effective Atwood number of the perturbed interface. A new pathway for geometric amplification of surface perturbations on an accelerating interface with contiguous density gradients is identified. A resonance condition between the density-gradient scalelength and the radius of the interface is also predicted based on a linearized analysis of Bernoulli's equation, potentially leading to enhanced perturbation growth. Comparison of the analytic treatment with detailed two-dimensional single-mode growth-factor simulations shows good agreement for low-mode numbers where the effects of spherical geometry are most manifested.

Article discussing research on the characterization of sub-nuclear changes in Caenorhabditis elegans embryos exposed to brief, intermediate and long-term anoxia to analyze anoxia-induced cell cycle arrest.

For years, farmers in the United States have looked with envy on their European counterparts ability to profitably farm the wind through ownership of distributed, utility-scale wind projects. Only within the past few years, however, has farmer- or community-owned windpower development become a reality in the United States. The primary hurdle to this type of development in the United States has been devising and implementing suitable business and legal structures that enable such projects to take advantage of tax-based federal incentives for windpower. This article discusses the limitations of such incentives in supporting farmer- or community-owned wind projects, describes four ownership structures that potentially overcome such limitations, and finally conducts comparative financial analysis on those four structures, using as an example a hypothetical 1.5 MW farmer-owned project located in the state of Oregon. We find that material differences in the competitiveness of each structure do exist, but that choosing the best structure for a given project will largely depend on the conditions at hand; e.g., the ability of the farmer(s) to utilize tax credits, preference for individual versus cooperative ownership, and the state and utility service territory in which the project will be located.

Transmission Electron Microscopy and x-ray diffraction were used to study compositional modulation in In{sub x}Ga{sub 1-x} N layers grown with compositions close to the miscibility gap. The samples (0.34 < x < 0.8) were deposited by molecular beam epitaxy using either a 200-nm-thick AlN or GaN buffer layer grown on a sapphire substrate. In the TEM imaging mode this modulation is seen as black/white fringes which can be considered as self-assembled thin quantum wells. Periodic compositional modulation leads to extra electron diffraction spots and satellite reflections in x-ray diffraction in the {theta}-2{theta} coupled geometry. The modulation period was determined using both methods. Larger modulation periods were observed for layers with higher In content and for those having larger mismatch with the underlying AlN buffer layer. Compositional modulation was not observed for a sample with x = 0.34 grown on a GaN buffer layer. Modulated films tend to have large 'Stokes shifts' between their absorption edge and photoluminescence peak.

High-level nuclear waste produced from fuel reprocessing operations at the Savannah River Site (SRS) requires pretreatment to remove Cs-137, Sr-90 and alpha-emitting radionuclides (i.e., actinides) prior to disposal. Separation processes planned at SRS include caustic side solvent extraction, for Cs-137 removal, and ion exchange/sorption of Sr-90 and alpha-emitting radionuclides with monosodium titanate (MST). The predominant alpha-emitting radionuclides in the highly alkaline waste solutions include plutonium isotopes Pu-238, Pu-239 and Pu-240. This paper describes results from a project funded by the U.S. Department of Energy Office of Cleanup Technology to produce sorbents that exhibit increased removal kinetics and capacity for Sr-90 and alpha-emitting radionuclides versus that of the baseline MST material. Testing indicated that MST samples prepared in the presence of organic-based templating reagents showed limited improvements in performance compared to the baseline MST. We observed significantly improved plutonium and neptunium removal performance with MST samples prepared upon the addition of a proprietary reagent. The modified MST offers the possibility of increased throughput and reduced solids handling in waste processing facilities at the SRS.

None

A method for computing direct-semidirect (DSD) neutron radiative capture is presented and applied to thermal neutron capture on {sup 19}F, {sup 27}Al, {sup 28,29.30}Si, {sup 35,37}Cl, {sup 39,41}K, {sup 56}Fe, and {sup 238}U, in support of data evaluation effort at the O.R.N.L. The DSD method includes both direct and semidirect capture; the latter is a core-polarization term in which the giant dipole resonance is formed. We study the effects of a commonly used ''density'' approximation to the EM operator and find it to be unsatisfactory for the nuclei considered here. We also study the magnitude of semidirect capture relative to the pure direct capture. Furthermore, we compare our results with those obtained from another direct capture code (Tedca [17]). We also compare our results with those obtained from analytical expression for external capture derived by Lane and Lynn [3], and its extension to include internal capture [7]. To estimate the effect of nuclear deformation on direct capture, we computed direct thermal capture on {sup 238}U with and without imposition of spherical symmetry. Direct capture for a spherically symmetric {sup 238}U was approximately 6 mb, while a quadrupole deformation of 0.215 on the shape of {sup 238}U lowers this cross section …

None

An explanation is given of the low value of R lambda triple bond A lambda/E(B - V), the ratio of absolute to selective extinction deduced from Type Ia supernova observations. The idea involves scattering by dust clouds located in the circumstellar environment, or at the highest velocity shells of the supernova ejecta. The scattered light tends to reduce the effective R lambda in the optical, but has an opposite effect in the ultraviolet. The presence of circumstellar dust can be tested by ultraviolet to near infrared observations and by multi-epoch spectropolarimetry of SNe Ia.

A recent study of long-drift CdZnTe (CZT) Frisch-ring detectors showed that fluctuations of the collected charge (and device response) depend on the device dimensions and the concentration of Te precipitates in the material. This observation, which could be explained as the cumulative effect of precipitates, led to the investigation of thin (1 mm) planar detectors, where the effects of precipitates can be more clearly ascertained. To perform the investigation, a measurement facility was developed that allowed for high-resolution spatial mapping of the performance of CZT devices. New measurements emerging from this facility provided the first detailed comparisons of the micro-scale X-ray maps and infrared microscopy images for thin CZT samples. Analysis of the data showed conclusively that local deteriorations of device response fully correlate with Te precipitates seen in the IR images. Effects of surface processing conditions on the detector response were also clearly observed.

Optical microscopy, scanning electron microscopy, and transmission electron microscopy were employed to examine the interfacial microstructural effects of impurities in alumina substrates used to fabricate alumina-niobium interfaces via liquid-film-assisted joining. Three types of alumina were used: undoped high-purity single-crystal sapphire; a high-purity, high-strength polycrystalline alumina; and a lower-purity, lower-strength polycrystalline alumina. Interfaces formed between niobium and both the sapphire and high-purity polycrystalline alumina were free of detectable levels of impurities. In the lower-purity alumina, niobium silicides were observed at the alumina-niobium interface and on alumina grain boundaries near the interface. These silicides formed in small-grained regions of the alumina and were found to grow from the interface into the alumina along grain boundaries. Smaller silicide precipitates found on grain boundaries are believed to form upon cooling from the bonding temperature.

This paper presents an efficient full-wave time-domain simulator for accurate modeling of PIN diode switches. An equivalent circuit of the PIN diode is extracted under different bias conditions using a drift-diffusion physical model. Net recombination is modeled using a Shockley-Read-Hall process, while generation is assumed to be dominated by impact ionization. The device physics is coupled to Maxwell's equations using extended-FDTD formulism. A complete set of results is presented for the on and off states of the PIN switch. The results are validated through comparison with independent measurements, where good agreement is observed. Using this modeling approach, it is demonstrated that one can efficiently optimize PIN switches for better performance.

High Energy Density Physics (HEDP) applications require high line charge density ion beams. An efficient method to obtain this type of beams is to extract a long pulse, high current beam from a gun at high energy, and let the beam pass through a decelerating field to compress it. The low energy beam-bunch is loaded into a solenoid and matched to a Brillouin flow. The Brillouin equilibrium is independent of the energy if the relationship between the beam size (a), solenoid magnetic field strength (B) and line charge density is such that (Ba){sup 2} is proportional to the line charge density. Thus it is possible to accelerate a matched beam at constant line charge density. An experiment, NDCX-1c is being designed to test the feasibility of this type of injectors, where we will extract a 1 microsecond, 100 mA, potassium beam at 160 keV, decelerate it to 55 keV (density {approx}0.2 {micro}C/m), and load it into a 2.5 T solenoid where it will be accelerated to 100-150 keV (head to tail) at constant line charge density. The head-to-tail velocity tilt can be used to increase bunch compression and to control longitudinal beam expansion. We will present the physics design and …

We describe the fabrication and assembly of the first prototype 201. 25 MHz copper cavity for the muon ionization cooling experiment (MICE). This cavity was developed by the US MUCOOL collaboration and will be tested in the new MUCOOL Test Area at Fermilab. We outline the component and subassembly fabrication steps and the various metal forming and joining methods used to produce the final cavity shape. These include spinning, brazing, TIG welding, electron beam welding, electron beam annealing and deep drawing. Some of the methods developed for this cavity are novel and offer significant cost savings over conventional methods.

None

We describe a genetic variation map for the chicken genome containing 2.8 million single nucleotide polymorphisms (SNPs), based on a comparison of the sequences of 3 domestic chickens (broiler, layer, Silkie) to their wild ancestor Red Jungle Fowl (RJF). Subsequent experiments indicate that at least 90% are true SNPs, and at least 70% are common SNPs that segregate in many domestic breeds. Mean nucleotide diversity is about 5 SNP/kb for almost every possible comparison between RJF and domestic lines, between two different domestic lines, and within domestic lines--contrary to the idea that domestic animals are highly inbred relative to their wild ancestors. In fact, most of the SNPs originated prior to domestication, and there is little to no evidence of selective sweeps for adaptive alleles on length scales of greater than 100 kb.

The effects of harvest-created canopy gaps in bottomland hardwood forests on arthropod abundance and, hence, the foraging ecology of birds are poorly understood. I predicted that arthropod abundance would be high near edges of group-selection harvest gaps and lower in the surrounding forest, and that male Hooded Warblers (Wilsonia citrina) foraging near gaps would find more prey per unit time than those foraging in the surrounding forest. In fact, arthropod abundance was greater >100 m from a gap edge than at 0-30 m or 30-100 m from an edge, due to their abundance on switchcane (Arundinaria gigantea); arthropods did not differ in abundance among distances from gaps on oaks (Quercus spp.) or red maple (Acer rubrum). Similarly, Hooded Warbler foraging attack rates were not higher near gap edges: when foraging for fledglings, attack rate did not differ among distances from gaps, but when foraging for themselves, attack rates actually were lower 0-30 m from gap edges than 30-100 m or >100 m from a gap edge. Foraging attack rate was positively associated with arthropod abundance. Hooded Warblers apparently encountered fewer prey and presumably foraged less efficiently where arthropods were least abundant, i.e., near gaps. That attack rates among birds foraging …

The hydrogen economy is not possible if the safety standards currently applied to liquid hydrogen and hydrogen gas by many laboratories are applied to devices that use either liquid or gaseous hydrogen. Methane and propane are commonly used by ordinary people without the special training. This report asks, 'How is hydrogen different from flammable gasses that are commonly being used all over the world?' This report compares the properties of hydrogen, methane and propane and how these properties may relate to safety when they are used in both the liquid and gaseous state. Through such an analysis, sensible safety standards for the large-scale (or even small-scale) use of liquid and gaseous hydrogen systems can be developed. This paper is meant to promote discussion of issues related to hydrogen safety so that engineers designing equipment can factor sensible safety standards into their designs.

The proliferation of nuclear, chemical, and biological weapons (collectively known as weapons of mass destruction, or WMD) and the potential acquisition and use of WMD against the world by terrorists are extremely serious threats to international security. These threats are complex and interrelated. There are myriad routes to weapons of mass destruction--many different starting materials, material sources, and production processes. There are many possible proliferators--threshold countries, rogue states, state-sponsored or transnational terrorists groups, domestic terrorists, and even international crime organizations. Motives for acquiring and using WMD are similarly wide ranging--from a desire to change the regional power balance, deny access to a strategic area, or alter international policy to extortion, revenge, or hate. Because of the complexity of this threat landscape, no single program, technology, or capability--no silver bullet--can solve the WMD proliferation and terrorism problem. An integrated program is needed that addresses the WMD proliferation and terrorism problem from end to end, from prevention to detection, reversal, and response, while avoiding surprise at all stages, with different activities directed specifically at different types of WMD and proliferators. Radiation detection technologies are an important tool in the prevention of proliferation. A variety of new developments have enabled enhanced performance in …

We present a novel approach for highly interactive remote delivery of visualization results. Instead of real-time rendering across the internet, our approach, inspired by QuickTime VR's Object Movieconcept, delivers pre-rendered images corresponding to different viewpoints and different time steps to provide the experience of 3D and temporal navigation. We use tiled, multiresolution image streaming to consume minimum bandwidth while providing the maximum resolution that a user can perceive from a given viewpoint. Since image data, a viewpoint and time stamps are the only required inputs, our approach is generally applicable to all visualization and graphics rendering applications capable of generating image files in an ordered fashion. Our design is a form of latency-tolerant remote visualization, where visualization and Rendering time is effectively decoupled from interactive exploration. Our approach trades off increased interactivity, flexible resolution (for individual clients), reduced load and effective reuse of coherent frames between multiple users (from the servers perspective) at the expense of unconstrained exploration. A normal web server is the vehicle for providing on-demand images to the remote client application, which uses client-pull to obtain and cache only those images required to fulfill the interaction needs. This paper presents an architectural description of the system along …