The ''Cold War'' was not fought only by soldiers but by scientists and engineers in Laboratories and plants located throughout the world. With the fall of the Berlin Wall, the ''Cold War'' was effectively over, but the weapons of nuclear war remained. Following signing of START 2 (Strategic Arms Reduction Treaty) in 1993, up to 100 tonnes of weapons usable plutonium is expected to be declared excess by the Super Powers. Steps must be taken to address the proliferation risks associated with this plutonium. Again the scientist and engineers, who were the ''Cold War'' warriors, are being asked to develop methods to disposition this plutonium such that it can never again be used for weapons. Will we burn the plutonium in reactors or immobilize the plutonium either in a glass or ceramic matrix? Interesting challenges face chemists and chemical engineers developing immobilization techniques to render the plutonium both environmentally benign, and proliferation resistant.

Helical dipole magnets are required in a project for the Relativistic Heavy Ion Collider (RHIC) to control and preserve the beam polarization in order to allow the collision of polarized proton beams. Specifications are for low current superconducting magnets with a 100 mm coil aperture and a 4 Tesla field in which the field rotates 360 degrees over a distance of 2.4 meters. A magnet meeting the requirements has been developed that uses a small diameter cable wound into helical grooves machined into a thick-walled aluminum cylinder.

Charged vector D*{sup +}(2010) meson production is studied in a high energy neutrino bubble chamber experiment with mean neutrino energy of 141 GeV. The D*{sup +} are produced in (5.6 {+-} 1.8)% of the neutrino charged current interactions, indicating a steep increase of cross section with energy. The mean fractional hadronic energy of the D*{sup +} meson is 0.55 {+-} 0.06.

Holography has been used successfully in combination with conventional optics for the first time in a large cryogenic bubble chamber, the 15-Foot Bubble Chamber at Fermilab, during a physics run. The innovative system combined the reference beam with the object beam, illuminating a conical volume of {approx} 1.4 m{sup 3}. Bubble tracks from neutrino interactions with a width of {approx} 120 {micro}m have been recorded with good contrast. The ratio of intensities of the object light to the reference light striking the film is called the Beam Branching Ratio. We obtained in our experiment an exceedingly small minimum-observable ratio of (0.54 {+-} 0.21) x 10{sup -7}. The technology has the potential for a wide range of applications.

A variety of prototype high penetration wind-diesel hybrid power systems have been implemented with different amounts of energy storage. They range from systems with no energy storage to those with many hours worth of energy storage. There has been little consensus among wind-diesel system developers as to the appropriate role and amount of energy storage in such systems. Some researchers advocate providing only enough storage capacity to supply power during the time it takes the diesel genset to start. Others install large battery banks to allow the diesel(s) to operate at full load and/or to time-shift the availability of wind-generated electricity to match the demand. Prior studies indicate that for high penetration wind-diesel systems, short-term energy storage provides the largest operational and economic benefit. This study uses data collected in Deering, Alaska, a small diesel-powered village, and the hybrid systems modeling software Hybrid2 to determine the optimum amount of short-term storage for a particular high penetration wind-diesel system. These findings were then generalized by determining how wind penetration, turbulence intensity, and load variability affect the value of short term energy storage as measured in terms of fuel savings, total diesel run time, and the number of diesel starts.

Batteries in hybrid power applications that include intermittent generators, such as wind turbines, experience a very irregular pattern of charge and discharge cycles. Because battery life is dependent on both depth and rate of discharge (and other factors such as temperature, charging strategy, etc.), estimating battery life and optimally sizing batteries for hybrid systems is difficult. Typically, manufacturers give battery life data, if at all, as cycles to failure versus depth of discharge, where all discharge cycles are assumed to be under conditions of constant temperature, current, and depth of discharge. Use of such information directly can lead to gross errors in battery lifetime estimation under actual operating conditions, which may result in either a higher system cost than necessary or an undersized battery bank prone to early failure. Even so, most current battery life estimation algorithms consider only the effect of depth of discharge on cycle life. This paper will discuss a new battery life prediction method, developed to investigate the effects of two primary determinants of battery life in hybrid power applications, varying depths of discharge and varying rates of discharge. A significant feature of the model is that it bases its analysis on battery performance and cycle …

The Photovoltaic Manufacturing Technology (PVMaT) project is helping the U.S. photovoltaic (PV) industry extend its world leadership role in manufacturing and stimulate the commercial development of PV modules and systems. Initiated in 1990, PVMaT is being carried out in several directed and staggered phases to support industry`s continued progress. Thirteen subcontracts awarded in FY 1996 under Phase 4A emphasize improvement and cost reduction in the manufacture of full-system PV products. Areas of work in Phase 4A included, but were not limited to, issues such as improving module-manufacturing processes; system and system-component packaging, integration, manufacturing, and assembly; product manufacturing flexibility; and balance-of-system development with the goal of product manufacturing improvements. These Phase 4A, product-driven manufacturing research and development (R&D) activities are now completing their second phase. Progress under these Phase 4A and remaining Phase 2B subcontracts from the earlier PVMaT solicitation are summarized in this paper. Evaluations of the success of this project have been carried out in FY 1995 and late FY 1996. This paper examines the 1997 cost/capacity data that have been collected from active PVMaT manufacturers.

Twenty one hundred metric tons of spent nuclear fuel are stored in two concrete pools on the Hanford Site, known as the K Basins, near the Columbia River. The deteriorating conditions of the fuel and the basins provide engineering and management challenges to assure safe current and future storage. DE and S Hanford, Inc., part of the Fluor Daniel Hanford, Inc. lead team on the Project Hanford Management Contract, is constructing facilities and systems to move the fuel from current wet pool storage to a dry interim storage facility away from the Columbia River, and to treat and dispose of K Basins sludge, debris and water. The process starts in the K Basins where fuel elements will be removed from existing canisters, washed, and separated from sludge and scrap fuel pieces. Fuel elements will be placed in baskets and loaded into Multi-Canister Overpacks (MCOs) and into transportation casks. The MCO and cask will be transported into the Cold Vacuum Drying Facility, where free water within the MCO will be removed under vacuum at slightly elevated temperatures. The MCOs will be sealed and transported via the transport cask to the Canister Storage Building (CSB) in the 200 Area for staging prior …

Nuclear criticality parameters were developed as a basis for evaluating criticality safety for waste stored in the high-level waste tank farms on the Hanford Site in Washington State. The plutonium critical concentration and critical mass were calculated using a conservative waste model (CWM). The primary requirement of a CWM is that it have a lower neutron absorption than any actual waste. Graphs are provided of the critical mass as a function of plutonium concentration for spheres and for uniform slab layers in a 22.9-m-diameter tank. Minimum subcritical absorber-to-plutonium mass rates were calculated for waste components selected for their relative abundance and neutron absorption capacity. Comparison of measured absorber-to-plutonium mass ratios in their corresponding subcritical limit mass ratios provides a means of assessing whether criticality is possible for waste of the measured composition. A comparison is made between the plutonium critical concentrations in CWM solids and in a postulated real waste. This comparison shows that the actual critical parameters are likely to be significantly larger than those obtained using the CWM, thus providing confidence that the margin of safety obtained to the criticality safety evaluation is conservative.

CEBAF is a 4 GeV, 200 {micro}A five-pass recirculating superconducting electron accelerator that has been operating for nuclear physics research at full energy since November 95. The beam current has been increased to over 180 {micro}A at 4 GeV with the maximum current in the linac over 900 {micro}A. The superconducting cavities operate in a regime where the beam-induced voltage is comparable to the accelerating gradient. The operational limits and the issues required to maintain stable operation of the 1,497 MHz superconducting cavities will be discussed, together with the implications for the other accelerator systems. There are three experimental Halls which can run simultaneously with three interleaved 499 MHz bunch trains and RF separators. Operation with simultaneous beams to two Halls is now routine, and simultaneous three beam operation has been demonstrated. The maximum design current per bunch train (120 {micro}A) has been achieved. Hall B eventually requires beam currents as low as 1 nA (200 pA has been delivered) simultaneous with delivery of up to 200 {micro}A to the other Halls. The required beam current ratio of 10,000 has been achieved; development of 1 nA beam position monitors continues.

The CEBAF accelerator at Thomas Jefferson National Accelerator Facility (Jefferson Lab) uses a continuous electron beam with up to 800 kilowatts of average beam power. The laboratory beam containment policy requires that in the event of an errant beam striking a beam blocking device, the beam must be shut off by three methods in less than 1 millisecond. One method implemented is to shut off the beam at the gun. Two additional methods have been developed which use fast beam kickers to deflect the injector beam on to a water cooled aperture. The kickers designed and implemented at Jefferson lab are able to deflect the injector beam in less than 200 microseconds. The kicker system includes self-test and monitoring capabilities that enable the system to be used for personnel safety.

RF and magnet system configuration and monitoring tools are being implemented at Jefferson Lab to improve system reliability and reduce operating costs. They are prototype components of the Momentum Management System being developed. The RF is of special interest because it affects the momentum and momentum spread of the beam, and because of the immediate financial benefit of managing the klystron DC supply power. The authors describe present and planned monitoring of accelerating system parameters, use of these data, RF system performance calculations, and procedures for magnet configuration for handling beam of any of five beam energies to any of three targets.

Accurate measurement of path length and path length changes versus momentum (M{sub 56}) are critical for maintaining minimum beam energy spread in the CEBAF (Continuous Electron Beam Accelerator Facility) accelerator at the Thomas Jefferson National Accelerator Facility (Jefferson Lab). The relative path length for each circuit of the beam (1256m) must be equal within 1.5 degrees of 1497 MHz RF phase. A relative path length measurement is made by measuring the relative phases of RF signals from a cavity that is separately excited for each pass of a 4.2 {mu}s pulsed beam. This method distinguishes the path length to less than 0.5 path length error. The development of a VME based automated measurement system for path length and M{sub 56} has contributed to faster machine setup time and has the potential for use as a feedback parameter for automated control.

This paper describes the integrated approach used to manage environmental, safety, and health considerations related to the B Plant canyon exhaust air filters at the US Department of Energy (DOE) Hanford Site. The narrative illustrates the development and implementation of integrated safety management as applied to a facility and its systems undergoing deactivation. During their lifetime, the high efficiency particulate air (HEPA) filters prevented the release of significant quantities of radioactive materials into the air. As the material in B Plant AVESF accumulated on the filters, it created an unusual situation. Over long periods of time, the radiation dose from the filter loading, combined with aging and chemical exposure actually degrade those filters which were intended to protect against any release to the environment.

Radioisotope Thermoelectric Generators (RTG) convert heat generated by radioactive decay into electricity through the use of thermocouples. The RTGs have a long operating life, are reasonably lightweight, and require little or no maintenance, which make them particularly attractive for use in spacecraft. However, because RTGs contain significant quantities of radioactive materials, normally plutonium-238 and its decay products, they must be transported in packages built in accordance with Title 10, Code of Federal Regulations, Part 71 (10 CFR 71). To meet these regulations, a RTG Transportation System (RTGTS) that fully complies with 10 CFR 71 has been developed, which protects RTGs from adverse environmental conditions during normal conditions of transport (e.g., shock, vibration, and heat). To ensure the protection of RTGs from shock and vibration loadings during transport, extensive over-the-road testing was conducted on the RTG`S to obtain real-time recordings of accelerations of the air-ride suspension system trailer floor, packaging, and support structure. This paper provides an overview of the RTG`S, a discussion of the shock and vibration testing, and a comparison of the test results to the specified shock response spectra and power spectral density acceleration criteria.

A reliability model for the Thomas Jefferson National Accelerator Facility (formerly CEBAF) personnel safety system has been developed. The model, which was implemented using an Excel spreadsheet, allows simulation of all or parts of the system. Modularity os the model`s implementation allows rapid {open_quotes}what if{open_quotes} case studies to simulate change in safety system parameters such as redundancy, diversity, and failure rates. Particular emphasis is given to the prediction of failure modes which would result in the failure of both of the redundant safety interlock systems. In addition to the calculation of the predicted reliability of the safety system, the model also calculates availability of the same system. Such calculations allow the user to make tradeoff studies between reliability and availability, and to target resources to improving those parts of the system which would most benefit from redesign or upgrade. The model includes calculated, manufacturer`s data, and Jefferson Lab field data. This paper describes the model, methods used, and comparison of calculated to actual data for the Jefferson Lab personnel safety system. Examples are given to illustrate the model`s utility and ease of use.

The US Department of Energy (DOE) and the National Institutes of Health (NIH) conducted a workshop on Isotope-Based Medical Research in the Post Genome Era at NIH, Bethesda, Maryland, November 12--14, 1997. The workshop aimed at identifying the role of stable and radioisotopes for advanced diagnosis and therapy of a wide range of illnesses using the new information that comes from the human genome program. In this sense, the agenda addressed the challenge of functional genomics in humans. The workshop addressed: functional genomics in clinical medicine; new diagnostic potentials; new therapy potentials; challenge to tracer- and effector-pharmaceutical chemistry; and project plans for joint ventures.

This meeting is aimed primarily at signal processing and controls. The technical program for the 1997 Workshop includes a variety of efforts in the Signal Sciences with applications in the Microtechnology Area a new program at LLNL and a future area of application for both Signal/Image Sciences. Special sessions organized by various individuals in Seismic and Optical Signal Processing as well as Micro-Impulse Radar Processing highlight the program, while the speakers at the Signal Processing Applications session discuss various applications of signal processing/control to real world problems. For the more theoretical, a session on Signal Processing Algorithms was organized as well as for the more pragmatic, featuring a session on Real-Time Signal Processing.

Extracting optimal performance out of an orbit correction system is an important component of accelerator design and evaluation. The question of effectiveness vs. economy, however, is not always easily tractable. This is especially true in cases where betatron function magnitude and phase advance do not have smooth or periodic dependencies on the physical distance. In this report a program is presented using linear algebraic techniques to address this problem. A systematic recipe is given, supported with quantitative criteria, for arriving at an orbit correction system design with the optimal balance between performance and economy. The orbit referred to in this context can be generalized to include angle, path length, orbit effects on the optical transfer matrix, and simultaneous effects on multiple pass orbits.

Large quantities of radioactive wastes have been generated at the Hanford Site over its operating life. The wastes with the highest activities are stored underground in 177 large (mostly one million gallon volume) concrete tanks with steel liners. The wastes contain processing chemicals, cladding chemicals, fission products, and actinides that were neutralized to a basic pH before addition to the tanks to prevent corrosion of the steel liners. Because the mission of the Hanford Site was to provide plutonium for defense purposes, the amount of plutonium lost to the wastes was relatively small. The best estimate of the amount of plutonium lost to all the waste tanks is about 500 kg. Given uncertainties in the measurements, some estimates are as high as 1,000 kg (Roetman et al. 1994). The wastes generally consist of (1) a sludge layer generated by precipitation of dissolved metals from aqueous wastes solutions during neutralization with sodium hydroxide, (2) a salt cake layer formed by crystallization of salts after evaporation of the supernate solution, and (3) an aqueous supernate solution that exists as a separate layer or as liquid contained in cavities between sludge or salt cake particles. The identity of chemical species of plutonium in …

This paper addresses international standards which can be applied to the requirements for accelerator personnel safety systems. Particular emphasis is given to standards which specify requirements for safety interlock systems which employ programmable electronic subsystems. The work draws on methodologies currently under development for the medical, process control, and nuclear industries.

The method for current control of a photocathode source is described. This system allows for full remote control of a photocathode drive laser for resulting electron beam currents ranging from less than one microamp to a full current ranging from less than one microamp to a full current of five milliamps. All current modes are obtained by gating the drive laser with a series of electro-optical cells. The system remotely generates this control signal by assuming a mode of operation with the following properties selectable: Current mode as continuous or gated, micropulse density, macropulse gate width from single shot to 1ms duration, macropulse synchronization to A/C line voltage (60 Hz) or an external trigger, 60 Hz phase and slewing through 60 Hz when applicable. All selections are derived from programmable logic devices operating from a master-oscillator resulting in a discrete, phase stable, pulse control for the drive laser.

We propose a new approach for deriving the string field equations from a general sigma model on the world-sheet. This approach leads to an equation which combines some of the attractive features of both the renormalization group method and the covariant beta function treatment of the massless excitations. It has the advantage of being covariant under a very general set of both local and non-local transformations in the field space. We apply it to the tachyon, massless and first massive level, and show that the resulting field equations reproduce the correct spectrum of a left-right symmetric closed bosonic string.

We review the construction of the multiparametric inhomogeneousorthogonal quantum group ISO{sub q,r}(N) as a projection from SO{sub q,r}(N+2), and recall the conjugation that for N=4 leads to the quantum Poincare group. We study the properties of the universal enveloping algebra U{sub q,r}(iso(N)), and give an R-matrix formlation. A quantum Lie algebra and a bicovariant differential calculus on twisted ISO(N) are found.