An all solid-state kicker pulser for a high current induction accelerator (the Dual-Axis Radiographic Hydrodynamic Test facility DARHT-2) has been designed and fabricated. This kicker pulser uses multiple solid state modulators stacked in an inductive-adder configuration. Each modulator is comprised of multiple metal-oxide-semiconductor field-effect transistors (MOSFETs) which quickly switch the energy storage capacitors across a magnetic induction core. Metglas is used as the core material to minimize loss. Voltage from each modulator is inductively added by a voltage summing stalk and delivered to a 50 ohm output cable. A lumped element circuit model of the inductive adder has been developed to optimize the performance of the pulser. Results for several stalk geometries will be compared with experimental data.

A technique is developed to construct bulk hydroxyapatite (HAp) with different cellular structures. The technique involves the initial synthesis of nanocrystalline hydroxyapatite powder from an aqueous solution using water-soluble compounds and then followed by spray drying into agglomerated granules. The granules were further cold pressed and sintered into bulks at elevated temperatures. The sintering behavior of the HAp granules was characterized and compared with those previously reported. Resulting from the fact that the starting HAp powders were extremely fine, a relatively low activation energy for sintering was obtained. In the present study, both porous and dense structures were produced by varying powder morphology and sintering parameters. Porous structures consisting of open cells were constructed. Sintered structures were characterized using scanning electron microscopy and x-ray tomography. In the present paper, hydroxyapatite coatings produced by magnetron sputtering on silicon and titanium substrates will also be presented. The mechanical properties of the coatings were measured using nanoindentation techniques and microstructures examined using transmission electron microscopy.

The goal of this joint LLNL-CalEnergy project is to develop a method for precipitating marketable silica from spent Salton Sea Geothermal Field (SSGF) brines. Many markets for silica exist. We have initially targeted production of silica as a rubber additive. Silica reinforced rubber gives tires less rolling resistance, greater tear strength, and better adhesion to steel belts. Previous silica precipitates produced by CalEnergy from Salton Sea brines were not suitable as rubber additives. They did not to disperse well in the rubber precursors and produced inferior rubber. CalEnergy currently minimizes silica scaling in some of their production facilities by acidifying the brine pH. The rate of silica precipitation slows down as the pH is lowered, so that energy extraction and brine reinfection are possible without unacceptable amounts of scaling even with more than 700 ppm SiO{sub 2} in solution. We are adding a step in which a small amount of base is added to the acidified brine to precipitate silica before reinfection. By carefully controlling the type, rate, and amount of base addition, we can optimize the properties of the precipitate to approach those of an ideal rubber additive.

The High Energy and Nuclear Physics Data Access GrandChallenge project has developed an optimizing storage access softwaresystem that was prototyped at RHIC. It is currently undergoingintegration with the STAR experiment in preparation for data taking thatstarts in mid-2000. The behavior and lessons learned in the RHIC MockData Challenge exercises are described as well as the observedperformance under conditions designed to characterize scalability. Up to250 simultaneous queries were tested and up to 10 million events across 7event components were involved in these queries. The system coordinatesthe staging of "bundles" of files from the HPSS tape system, so that allthe needed components of each event are in disk cache when accessed bythe application software. The caching policy algorithm for thecoordinated bundle staging is described in the paper. The initialprototype implementation interfaced to the Objectivity/DB. In this latestversion, it evolved to work with arbitrary files and use CORBA interfacesto the tag database and file catalog services. The interface to the tagdatabase and the MySQL-based file catalog services used by STAR aredescribed along with the planned usage scenarios.

A proprietary tritium loading bed developed by Molecular Separations, Inc (MSI) has been shown to selectively load tritiated water as waters of hydration at near ambient temperatures. Tests conducted with a 126 {micro}C{sub 1} tritium/liter water standard mixture showed reductions to 25 {micro}C{sub 1}/L utilizing two, 2-meter long columns in series. Demonstration tests with Hanford Site wastewater samples indicate an approximate tritium concentration reduction from 0.3 {micro}C{sub 1}/L to 0.07 {micro}C{sub 1}/L for a series of two, 2-meter long stationary column beds Further reduction to less than 0.02 {micro}C{sub 1}/L, the current drinking water maximum contaminant level (MCL), is projected with additional bed media in series. Tritium can be removed from the loaded beds with a modest temperature increase and the beds can be reused Results of initial tests are presented and a moving bed process for treating large quantities of wastewaters is proposed. The moving bed separation process appears promising to treat existing large quantities of wastewater at various US Department of Energy (DOE) sites. The enriched tritium stream can be grouted for waste disposition. The separations system has also been shown to reduce tritium concentrations in nuclear reactor cooling water to levels that allow reuse. Energy requirements to …

We present a new technique for progressive approximation and compression of polygonal objects in images. Our technique uses local parameterizations defined by meshes of convex polygons in the plane. We generalize a tensor product wavelet transform to polygonal domains to perform multiresolution analysis and compression of image regions. The advantage of our technique over conventional wavelet methods is that the domain is an arbitrary tessellation rather than, for example, a uniform rectilinear grid. We expect that this technique has many applications image compression, progressive transmission, radiosity, virtual reality, and image morphing.

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LH{sub 2}) or ambient-temperature compressed hydrogen (CH{sub 2}). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (fuel flexibility, lower energy requirement for hydrogen liquefaction and reduced evaporative losses). The work described here is directed at verifying that commercially available pressure vessels can be safely used to store liquid hydrogen. The use of commercially available pressure vessels significantly reduces the cost and complexity of the insulated pressure vessel development effort. This paper describes a series of tests that have been done with aluminum-lined, fiber-wrapped vessels to evaluate the damage caused by low temperature operation. All analysis and experiments to date indicate that no significant damage has resulted. Required future tests are described that will prove that no technical barriers exist to the safe use of aluminum-fiber vessels at cryogenic temperatures.

High pressure xenon ionization chamber detectors are possible alternatives to traditional thallium doped sodium iodide (NaI(Tl)) and hyperpure germanium as gamma spectrometers in certain applications. Xenon detectors incorporating a Frisch grid exhibit energy resolutions comparable to cadmium/zinc/telluride (CZT) (e.g. 2% {at} 662keV) but with far greater sensitive volumes. The Frisch grid reduces the position dependence of the anode pulse risetimes, but it also increases the detector vibration sensitivity, anode capacitance, voltage requirements and mechanical complexity. We have been investigating the possibility of eliminating the grid electrode in high-pressure xenon detectors and preserving the high energy resolution using electronic risetime compensation methods. A two-electrode cylindrical high pressure xenon gamma detector coupled to time-to-amplitude conversion electronics was used to characterize the pulse rise time of deposited gamma photons. Time discrimination was used to characterize the pulse rise time versus photo peak position and resolution. These data were collected to investigate the effect of pulse rise time compensation on resolution and efficiency.

This is the first of two papers describing the application of simulator-optimization methods to a natural gas storage field development planning problem. The results presented here illustrate the large gains in cost-effectiveness that can be made by employing the reservoir simulator as the foundation for a wide-ranging search for solutions to management problems. The current paper illustrates the application of these techniques given a deterministic view of the reservoir. A companion paper will illustrate adaptations needed to accommodate uncertainties regarding reservoir properties.

Migration of individuals between populations may increase the selection pressure. This has the desirable consequence of speeding up convergence, but it may result in an excessively rapid loss of variation that may cause the search to fail. This paper investigates the effects of migration on the distribution of fitness. It considers arbitrary migration rates and topologies with different number of neighbors, and it compares algorithms that are configured to have the same selection intensity. The results suggest that migration preserves more diversity as the number of neighbors of a deme increases.

A rigorous extraction of the deuteron charge form factors from tensor polarization data in elastic electron-deuteron scattering, at given values of the 4-momentum transfer, is presented. Then the world data for elastic electron-deuteron scattering is used to parameterize, in three different ways, the three electromagnetic form factors of the deuteron in the 4-momentum transfer range 0-7 fm. This procedure is made possible with the advent of recent polarization measurements. The parameterizations allow a phenomenological characterization of the deuteron electromagnetic structure. They can be used to remove ambiguities in the form factors extraction from future polarization data.

X-ray backlighting is a powerful tool for diagnosing a large variety of high-energy-density phenomena. Traditional area backlighting techniques used at Nova and Omega cannot be extended efficiently to NIF-scale. New, more efficient backlighting sources and techniques are required and have begun to show promising results. These include a backlit-pinhole point projection technique, pinhole and slit arrays, distributed polychromatic sources, and picket fence backlighters. In parallel, there have been developments in improving the data SNR and hence quality by switching from film to CCD-based recording media and by removing the fixed-pattern noise of MCP-based cameras.

[Tl(OCH{sub 2}CH{sub 3})]{sub 4}, (1) was reacted with excess HOR to prepare a series of [Tl(OR)]{sub n} where OR= OCHMe{sub 2} (2, n = 4), OCMe{sub 3} (3, n = 4), OCH{sub 2}CMe{sub 3} (4, n = 4), OC{sub 6}H{sub 3}(Me){sub 2}-2,6 (5, n = {infinity}), and OC{sub 6}H{sub 3}(Pr{sup i}){sub 2}-2,6 (6, n = {infinity}). Single crystal X-ray diffraction was used to determine the structure of compounds ligated by more sterically demanding ligands. Compound 4 was found to adopt a cubane structure, while 5 and 6 formed linear polymeric structures. These compounds were additionally characterized by {sup 203,205}Tl solution and {sup 205}Tl solid state NMR. Compounds 1--4 were found to remain intact in solution while the polymeric species, 5 and 6, appeared to be fluxional. While variations in the solution and solid state structures for the tetrameric [Tl(OR)]{sub 4} and polymeric [Tl(OAr)]{sub {infinity}} may be influenced by the steric hindrance of their respective ligands, the covalency of the species is believed to be more an effect of the parent alcohol acidity.

Plate impact experiments were performed on B270 glass in order to measure the properties of post-failure wave material. The initial failure wave velocity is 1.27 km/s . After the material is released, the failure wave velocity drops to 0.65 km/s. At a stress of 6.72 GPa, the sound speed in the failed material is 4.97 km/s (compare to 5.79 km/s in the intact material) with a density comparable to the predicted shock value. At a stress of 0.26 GPa, the average sound speed in the failed material is 3.55 km/s, and the density drops to 65% of the intact value. The spall strength of the failed material is greater than 0.14 GPa.

This work studies multiscale phenomena in silicon micro-resonators which comprise the mechanical components of next-generation Micro-Electro-Mechanical Systems (MEMS). Unlike their larger relatives, the behavior of these sub-micron MEMS is not described well by conventional continuum models and finite elements, but it is determined appreciably by the interplay between physics at the Angstrom, nanometer and micron scales. As device sizes are reduced below the micron scale, atomistic processes cause systematic deviations from the behavior predicted by conventional continuum elastic theory. [1] These processes cause anomalous surface effects in the resonator frequency and quality factor--even for single crystal devices with clean surfaces due to thermal fluctuations. They also lead to unconventional failure mechanisms. The simulation of these atomistic effects is a challenging problem due to the large number of atoms involved and due to the fact that they are finite temperature phenomena. Our simulations include up to two million atoms in the device itself, and hundreds of millions more are in the proximal regions of the substrate. A direct, atomistic simulation of the motion of this many atoms is prohibitive, and it would be inefficient. The micronscale processes in the substrate are well-described by finite elements, and an atomistic simulation is not …

The use of liquid walls for fusion reactors could help solve problems associated with material erosion from high plasma heat-loads and neutronic activation of structures. A key issue analyzed here is the influx of impurity ions to the core plasma from the vapor of liquid side-walls. Numerical 2D transport simulations are performed for a slab geometry which approximates the edge region of a reactor-size tokamak. Both lithium vapor (from Li or SnLi walls) and fluorine vapor (from Flibe walls) are considered for hydrogen edge-plasmas in the high- and low-recycling regimes. It is found that the minimum influx is from lithium with a low-recycling hydrogen plasma, and the maximum influx occurs for fluorine with a high-recycling hydrogen plasma.

Electrical conductivities of fluid oxygen were measured between 30 and 80 GPa at a few 1000 K. These conditions were achieved with a reverberating shock wave technique. The measured conductivities were several orders of magnitude lower than measured previously on the single shock Hugoniot because of lower temperatures achieved under shock reverberation. Extrapolation of these data suggests that the minimum metallic conductivity of a metal will be reached near 100 GPa.

We developed the Scaled Thermal Explosion Experiment (STEX) to provide a database of reaction violence from thermal explosion of explosives of interest. A cylinder of explosive, 1, 2 or 4 inches in diameter, is confined in a steel cylinder with heavy end caps, and heated under controlled conditions until it explodes. Reaction violence is quantified by micropower radar measurement of the cylinder wall velocity, and by strain gauge data at reaction onset. Here we describe the test concept and design, show that the conditions are well understood, and present initial data with HMX-based explosives. The HMX results show that an explosive with high binder content yields less-violent reactions that an explosive with low binder content, and that the HMX phase at the time of explosion plays a key role in reaction violence.

A Mach-Zehnder interferometer was used for analysis of pressure waves generated by ultrashort laser pulse ablation of water. It was found that the shock wave generated by plasma formation rapidly decays to an acoustic wave. Both experimental and theoretical studies demonstrated that the energy transfer to the mechanical shock was less than 1%.

The success of nonrigid motion analysis using physical finite element model is dependent on the mesh that characterizes the object's geometric structure. We suggest a deformable mesh adapted to the natural features of images. The adaptive mesh requires much fewer number of nodes than the fixed mesh which was used in our previous work. We demonstrate the higher efficiency of the adaptive mesh in the context of estimating burn scar elasticity relative to normal skin elasticity using the observed 2D image sequence. Our results show that the scar assessment method based on the physical model using natural feature adaptive mesh can be applied to images which do not have artificial markers.

A better understanding of the formation of large-scale structure in the Universe is arguably the most pressing question in cosmology. The most compelling and promising theoretical paradigm, Inflation + Cold Dark Matter, holds that the density inhomogeneities that seeded the formation of structure in the Universe originated from quantum fluctuations arising during inflation and that the bulk of the dark matter exists as slowing moving elementary particles (cold dark matter) left over from the earliest, fiery moments. Large redshift surveys (such as the SDSS and 2dF) and high-resolution measurements of CBR anisotropy (to be made by the MAP and Planck Surveyor satellites) have the potential to decisively test Inflation + Cold Dark Matter and to open a window to the very early Universe and fundamental physics.

This presentation summarizes efforts to develop and apply chemically bonded phosphate ceramic (Ceramicrete{trademark}) technology for radiation shielding applications. The specific application being targeted is a packaging system for spent-fuel transport and storage. Using Ceramicrete technology under ambient conditions, the authors can produce dense and hard ceramic forms that incorporate second-phase material. Ceramicrete inherently is a superior shielding material because it contains large amounts of bound water in its crystal structure and can be cast in any shape. A parametric study was conducted on Ceramicrete that contained second-phase additions of metals and other ceramic powders. Results of various standardized tests that included mechanical performance and shielding from neutrons are presented. The fabrication of complex shapes and structures by Ceramicrete technology is discussed. Ceramicrete is compared with other currently available shielding systems that are based on concrete and polymers.

Two-phase characteristic curves are necessary for the simulation of water and vapor flow in porous media. Existing functions such as van Genuchten, Brooks and Corey, and Luckner et al. have significant limitations in the dry region as the liquid saturation goes to zero. This region, which is important in a number of applications including liquid and vapor flow and vapor-solid sorption, has been the subject of a number of previous investigations. Most previous studies extended standard capillary pressure curves into the adsorption region to zero water content and required a refitting of the revised curves to the data. In contrast, the present method provides for a simple extension of existing capillary pressure curves without the need to refit the experimental data. Therefore, previous curve fits can be used, and the transition between the existing fit and the relationship in the adsorption region is easily calculated. The data-model comparison shows good agreement. This extension is a simple and convenient way to extend existing curves to the dry region.

This report compiles the presentations made at the 1999 Photovoltaic Performance and Reliability Workshop, held on October 18-21, 1999, in Vail, Colorado. The theme of the workshop was ''Setting a Standard for PV Performance and Reliability,'' with the focus on testing, test methods, evaluation, and standards. The workshop provided a venue for technical discussions on four topical areas: module rating, module qualification, power processing, and systems. Includes the following. (1) Module Performance Rating. IEEE PAR 1479 ''Draft Recommended Practice for the Evaluation of Photovoltaic Module Energy Production'' - proceed with validating the models and inputs; look closely at the need to develop a similar activity for system energy rating. (2) Module Qualification Testing. IEEE Std.1262 ''Recommended Practice for Qualification of PV Modules'' - continue validation of proposed new qualification tests at NREL, ISPRA, and US PV industry and test lab facilities. Reliability testing should be done and should include module qualification. (3) Power Processing. The most pressing concerns expressed by individuals included system design and system components integration aspects; reliability assurance; interconnection and the need for a uniform, national approach; testing; and, infrastructure development. (4) Systems Evaluation. The most pressing concerns reiterated the concerns in the power processing session. IEEE …