Solid friction is considered by some to be a fundamental property of two contacting materials, while others consider it to be a property of the larger tribosystem in which the materials are contained. A set of sliding friction experiments were designed to investigate the hypothesis that the unlubricated sliding friction between two materials is indeed a tribosystems-related property and that the relative influence of the materials properties or those of the machine on friction varies from one situation to another. Three tribometers were used: a friction microprobe (FMP), a typical laboratory-scale reciprocating pin-on-flat device, and a heavy-duty commercial wear tester. The slider material was stainless steel (AISI 440C) and the flat specimen material was an ordered alloy of Ni{sub 3}Al (IC-50). Sphere-on-flat geometry was used at ambient conditions and at normal forces ranging from 0.01 N to 100 N and average sliding velocities of 0.01 to 100.0 mm/s. The nominal, steady-state sliding friction coefficient tended to decrease with increases in normal force for each of the three tribometers, and the steady state value of sliding friction tended to increase as the mass of the machine increased. The variation of the friction force during sliding was also a characteristic of the …

Results from modeling of transformation toughening in brittle materials using a discrete micromechanical model are presented. The material is represented as a two-dimensional triangular array of nodes connected by elastic springs. Microstructural effects are included by varying the spring parameters for the bulk, grain boundaries, and transforming particles. Using the width of the damage zone and the effective compliance (after the initial creation of the damage zone) as measures of fracture toughness, we find that there is a strong dependence of toughness on the amount, size, and shape of the transforming particles, with the maximum toughness achieved with the higher amounts of the larger particles.

The experimental study of the water-rock interaction shows that the secondary mineral assemblage depends on the water composition. For example, granite-pure water interaction produces zeolites (relatively low-dense, Mg-poor minerals), whereas seawater yields chlorites (high-dense, Mg-rich minerals). The reactions have volumetric effects from several % to 20 % in magnitude. Volume deformations in the heterogeneous matrix cause uneven mechanical strains. Reactions with the effect of about 0,1 vol.% may cause strains of the order of 100-1000 bars being enough for destruction of rocks. Signs and magnitudes of local volume changes depend on the mineral composition of the secondary assemblage. Hence, one can provide either healing or cracking of primary fractures, as desired, by changing the composition of water in the water-felsic rock system where some elements (Mg, Fe) are in lack. The techniques of "chemical hydrofracturing" looks promising as applied to a granite HDR massif. One can regulate the permeability of fractured flow paths by changing in concord the composition and pressure of the injected water. This approach should promote efficient extraction of the petrothermal energy.

High surface electric fields have been obtained in the first tests of a superconducting rf quadrupole device. The rf quadrupole fields were generated between niobium vanes 6.5 cm in length, with an edge radius of 2 mm, and with a beam aperture of 6 mm diameter. In tests at 4.2 K, the 64 MHz device operated cw at peak surface electric fields of 128 MV/m. Virtually no electron loading was observed at fields below 100 MV/m. It was possible to operate at surface fields of 210 MV/m in pulses of 1 msec duration using a 2.5 kW rf source. For the vane geometry tested, more than 10 square centimeters of surface support a field greater than 90% of the peak field. The present result indicates that electric fields greater than 100 MV/m can be obtained over an appreciable area, sufficient for some accelerator applications. It also shows that superconducting rf technology may provide an extended range of options for rf quadrupole design. 7 refs., 4 figs.

Differential geometry provides a natural family of coordinate systems, the Frenet frame, in which to specify the geometric properties of magnet winding. By a modification of the Euler-Bernoulli thin rod model, the strain energy is defined with respect to this frame. Then it is minimized by a direct method from the calculus of variations. The mathematics, its implementation in a computer program, and some analysis of an SSC dipole by the program will be described. 16 refs.

Recent studies of nuclear mass models show that it is essential to account for the Coulomb redistribution energy when calculating the nuclear potential energy in the heavy-element region. Results obtained by use of a mass model that includes Coulomb redistribution effects on analyzed. Q values of {alpha} and {beta} decay are calculated. Half-lives for {alpha} decay are estimated by use of the Viola-Seaborg systematics. For EC, {beta}{sup +} decay and {beta}{sup {minus}} decay, half-lives are calculated in a microscopic QRPA model. Calculated single-particle level structures in the heavy-element regions are presented. These indicate possible regions of isomers that would be unusually stable with respect to spontaneous fission and {alpha} decay. Finally, we discuss the implications of earlier extensive work on fission properties of nuclei in this region.

Interest in interactive 3-D graphics has exploded of late, fueled by (a) the allure of using scientific visualization to go where no-one has gone before'' and (b) by the development of new input devices which overcome some of the limitations imposed in the past by technology, yet which may be ill-suited to the kinds of interaction required by researchers active in scientific visualization. To resolve this tension, we propose a flat 5-D'' environment in which 2-D graphics are augmented by exploiting multiple human sensory modalities using cheap, conventional hardware readily available with personal computers and workstations. We discuss how interactions basic to 3-D scientific visualization, like searching a solution space and comparing two such spaces, are effectively carried out in our environment. Finally, we describe 3DMOVE, an experimental microworld we have implemented to test out some of our ideas. 40 refs., 4 figs.

A series of experiments was conducted using SRL 165 synthetic waste glass to investigate the effects of surface preparation and leaching solution composition on the alteration of the glass. Samples of glass with as-cast surfaces produced smooth reaction layers and some evidence for precipitation of secondary phases from solution. Secondary phases were more abundant in samples reacted in deionized water than for those reacted in a silicate solution. Samples with saw-cut surfaces showed a large reduction in surface roughness after 7 days of reaction in either solution. Reaction in silicate solution for up to 91 days produced no further change in surface morphology, while reaction in DIW produced a spongy surface that formed the substrate for further surface layer development. The differences in the surface morphology of the samples may create microclimates that control the details of development of alteration layers on the glass; however, the concentrations of elements in leaching solutions show differences of 50% or less between samples prepared with different surface conditions for tests of a few months duration. 6 refs., 7 figs., 1 tab.

An examination of a coherency criteria for high velocity jets is discussed in this paper. An analysis of the classical Pugh, Eichelberger, Rostoker jetting theory is used to develop an equation that defines the maximum coherent jet velocity as a function of the liner material sound speed, the liner beta angle, and the magnitude direction of the liner collapse velocity vector. The liner material sound speed is assumed to be the liner material shock velocity at the time of liner material collapse. This shock velocity is a function of the collapse pressure in the stagnation region and thus varies with time and position along the liner. The analysis indicates that coherent jets at velocities greater than three times the liner shock velocity are possible with some combinations of the beta and collapse vector angles while incoherent jets at velocities equal to two times the liner shock velocity could occur with other combinations. The objectives of this paper are to examine the theory used to calculate jet velocity and to develop a criteria for calculating the maximum coherent jet tip velocity. 13 refs., 6 figs.

Potassium dihydrogen phosphate (KDP) crystals have been used as harmonic converters on the Nova laser at LLNL for over six years. All crystals were coated with a single layer, quarterwave AR coating of porous silica with a refractive index of 1.22. This was prepared by a sol-gel process and was applied from a colloidal suspension by spin coating at room temperature. A few crystals were also coated with a methyl silicone coating prior to the application of the AR coating for environmental protection. The initial optical performance of all crystals was very good but there has been some deterioration over the years because of environmental and laser damage degradation. The deterioration in the silicone samples was, however, much less than the others. We are now in the process of replacing all ten KDP arrays with new crystals and will apply the silicone undercoat to all samples. Recently we have been evaluating a new perfluorinated organic polymer coating which has a refractive index of 1.29. This material is soluble in fluorinated solvents and can be applied by dip coating from solution at room temperature. We hope that this can provide environmental protection when applied to KDP and also act as an …

Sintered bars of Y-Ba-Cu oxide were partially melted using a quartz halogen lamp zone heating apparatus. The resulting multiphase samples showed varying degrees of melt texturing.'' It was found that the addition of YBa{sub 2}CuO{sub 5} powders to the sintered YBa{sub 2}Cu{sub 3}O{sub 7} prior to the zone melting process enhanced the growth of large textured grains. The best value of the critical current density was {approximately}10{sup 3} A/cm{sup 2} at 1.0 T and 77 K for the starting composition of YBa{sub 2}Cu{sub 3}O{sub 7} {sm bullet} (0.2)Y{sub 2}BaCuO{sub 5}. 11 refs., 5 figs.

The ability to measure critical currents in high {Tc} superconducting tapes on a local scale is valuable for optimizing the fabrication process. This paper describes the use of induced currents from a small noncontacting electromagnetic probe to determine the critical current density in a (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x}/Ag tape on a local scale. The technique forces full field penetration into the tape locally and infers the critical current density from the Bean critical state model, accounting for the Ag overlayers. Critical current images of the till can be obtained by scanning the probe over the tape surface with spatial resolution on the order of 1.0 mm. Results for tapes with different microstructures we discussed.

The remnant magnetic flux distribution in a single crystal and a sintered polycrystal was examined using the magnetic particle decoration technique. The single crystal, which was heavily twinned, showed only local order in the flux lattice. This was probably due to lattice distortions caused by interaction between twin boundaries and fluxons. In the polycrystal, flux pinning effectiveness was seen to vary significantly between grains, depending on size and orientation. Grains with the c axis nearly perpendicular to the applied magnetic field were most effective at pinning flux. Some features of the decoration patterns implied that the flux distribution was influenced by more than just the grains at the sample surface. 7 refs., 6 figs.

The results from the tests of the first large area (4 [times] 4 cm[sup 2]) planar silicon drift detector prototype in a pion beam are reported. The measured position resolution in the drift direction is ([sigma]=40 [plus minus] 10)[mu]m.

A preliminary measurement of the properties of W and Z production along with accompanying jets has been made in {anti p}p collisions at 1.8 TeV using the CDF detector at Fermilab. Distributions of jet multiplicity, and boson E{sub T}, with and without selection on jet multiplicity, were obtained. Agreement was found with perturbative QCD predictions.

Transient electrical potentials can be generated in plasmas by utilizing impulsive mirror-generated forces acting on the plasma electrons together with ion inertia to cause momentary charge imbalance. In the Mirrortron such potentials are generated by applying a rapidly rising (tens of nanoseconds) localized mirror field to the central region of a hot-electron plasma confined between static mirrors. Because of the loss-cone nature of the electron distribution the sudden appearance of the pulsed mirror tends to expel electrons, whereas the ion density remains nearly constant. The quasi-neutrality condition then operates to create an electrical potential the equipotential surfaces of which can be shown theoretically to be congruent with surfaces of constant B. An alternative way of generating transient potentials is to apply a pulse of high-power microwaves to a plasma residing on a magnetic field with a longitudinal gradient. This technique resembles one employed in the Pleiade experiments. At gigawatt power levels, such as those produced by a Free Electron Laser, the production of very high transient potentials is predicted. Fusion-relevant applications of these ideas include heavy-ion drivers for inertial fusion, and the possibility of employing these techniques to enhance the longitudinal confinement of fusion plasmas in multiple-mirror systems. 23 refs., …

Differential-algebraic equation (DAE) boundary value problems arise in a variety of applications, including optimal control and parameter estimation for constrained systems. In this paper we survey these applications and explore some of the difficulties associated with solving the resulting DAE systems. For finite difference methods, the need to maintain stability in the differential part of the system often necessitates the use of methods based on symmetric discretizations. However, these methods can suffer from instability and loss of accuracy when applied to certain DAE systems. We describe a new class of methods, Projected Implicit Runge-Kutta Methods, which overcomes these difficulties. We give convergence and stability results, and present numerical experiments which illustrate the effectiveness of the new methods. 20 refs., 1 tab.

Efficiencies of interstitial absorption during pulsed ND:YAG laser welding of vanadium were compared for nitrogen, oxygen, hydrogen, and water vapor. Influence of interstitial levels on the embrittlement of vanadium laser welds was also measured. For 1000 ppM contaminant levels in the weld atmosphere, weld hydrogen content increased 9 ppM, nitrogen content increased 190 ppM, and oxygen content increased from 500 ppM relative to baseplate levels. Welds in ultrahigh-purity argon atmospheres contained 3 ppM hydrogen, 40 ppM nitrogen, and 250 ppM oxygen. Longitudinal all-weld tensile specimens and notched-plate specimens were used to measure weld metal tensile properties at [minus]55C. All of the laser weld notch-strength ratios exceeded unity and weld metal tensile strengths all exceeded the baseplate values. For 1000 ppM atmosphere contaminant levels, the only significant decrease in ductility, as measured by reduction-in-area at fracture was for the weld atmosphere containing oxygen. Weld atmospheres containing 1% nitrogen also reduced the weld ductility, and resulted in the onset of cleavage fracture.

In the analysis of magnetic flux creep experiments it is assumed that, at a given temperature, the pinning energy which must be overcome by thermal activation depends on the magnetic induction and its gradient by U(B,{nabla}B){congruent} U{sub p}(B)(1-{nabla}B/{nabla}B{sub max}){sup n} where U{sub p} is the pinning well depth and {nabla}B{sub max} corresponds to the critical current density with no thermal activation. Customarily, n is assumed to be unity and any unusual temperature dependence of U{sub p} is then ascribed to a distribution of well depths. However, realistic assumptions about the shape of the pinning potential yield 3/2 {approx lt} n {approx lt} 2, which yields an apparent distribution of well depths in the conventional analysis. Simple models will be used to illustrate the characteristics of these two quite different origins for the apparent temperature dependence of well depth obtained from magnetic flux creep rates. 13 refs., 8 figs.

Recent studies of nuclear mass models show that it is essential to account for the Coulomb redistribution energy when calculating the nuclear potential energy in the heavy-element region. Results obtained by use of a mass model that includes Coulomb redistribution effects on analyzed. Q values of {alpha} and {beta} decay are calculated. Half-lives for {alpha} decay are estimated by use of the Viola-Seaborg systematics. For EC, {beta}{sup +} decay and {beta}{sup {minus}} decay, half-lives are calculated in a microscopic QRPA model. Calculated single-particle level structures in the heavy-element regions are presented. These indicate possible regions of isomers that would be unusually stable with respect to spontaneous fission and {alpha} decay. Finally, we discuss the implications of earlier extensive work on fission properties of nuclei in this region.

Remediation of the Department of Energy (DOE) Fernald site located north of Cincinnati will generate large quantities of low-level radwaste. This volume includes approximately 1,050,000 tons of material to be removed from eight waste pits comprising Operable Unit 1 (OU-1). The remedial alternative selected includes waste material excavation, drying and transportation by rail to a burial site in the arid west for disposal. Rail transportation was selected not only because rail transportation is safer than truck transportation, but also because of the sheer magnitude of the project and the availability of bulk rail car unloading facilities at a representative disposal site. Based upon current waste quantity estimates as presented in the Feasibility Study for OUI, a fully-loaded 47-car unit train would depart the Fernald site weekly for five years. This paper illustrates the steps taken to obtain agency and public acceptance of the Record of Decision for the remedy which hinged on rail transportation. A preliminary, but detailed, rail transportation plan was prepared for the project to support a series of CERCLA public meetings conducted in late 1994. Some of the major issues addressed in the plan included the following: (1) Scope of project leading to selection of rail transportation; …

The vector fields of the quantum Lie algebra are described for the quantum groups GL{sub q}(n), SL{sub q}(N) and SO{sub q}(N) as pseudodifferential operators on the linear quantum spaces covariant under the corresponding quantum group. Their expressions are simple and compact. It is pointed out that these vector fields satisfy certain characteristic polynomial identities. The real forms SU{sub q}(N) and SO{sub q}(N,R) are discussed in detail.

The results from the tests of the first large area (4 {times} 4 cm{sup 2}) planar silicon drift detector prototype in a pion beam are reported. The measured position resolution in the drift direction is ({sigma}=40 {plus_minus} 10){mu}m.

We summarize some of the areas of comparison with experimental data for which the ALICE code did poorly. We suggest some aspects which might be improved in the future. A crude accuracy factor is estimated as a predictive reliability based on the intercomparison exercise.