The experimental study of the water-rock interaction shows that the secondary mineral assemblage depends on the water composition. For example, granite-pure water interaction produces zeolites (relatively low-dense, Mg-poor minerals), whereas seawater yields chlorites (high-dense, Mg-rich minerals). The reactions have volumetric effects from several % to 20 % in magnitude. Volume deformations in the heterogeneous matrix cause uneven mechanical strains. Reactions with the effect of about 0,1 vol.% may cause strains of the order of 100-1000 bars being enough for destruction of rocks. Signs and magnitudes of local volume changes depend on the mineral composition of the secondary assemblage. Hence, one can provide either healing or cracking of primary fractures, as desired, by changing the composition of water in the water-felsic rock system where some elements (Mg, Fe) are in lack. The techniques of "chemical hydrofracturing" looks promising as applied to a granite HDR massif. One can regulate the permeability of fractured flow paths by changing in concord the composition and pressure of the injected water. This approach should promote efficient extraction of the petrothermal energy.

We demonstrate that there are regions of parameter space in the next-to-minimal (i.e. two-Higgs-doublet, one-Higgs-singlet superfield) supersymmetric extension of the SM for which none of the Higgs bosons are observable either at LEP2 with $\sqrt{s}=192 GeV$ and an integrated luminosity of $L=1000inverse pb$ or at the LHC with $L=600 inverse fb$.

Well SN-12 in the Seltjarnarnes low-temperature field in SW-Iceland was drilled to a depth of 2714 m in the fall of 1994. The well appeared to be almost non-productive at the end of drilling. A comprehensive ten day stimulation program was, therefore, initiated. The program involved, firstly, high-pressure wellhead injection and, secondly, high-pressure injection below a packer placed at 1412 m depth. After about twelve hours of wellhead stimulation the pressure dropped suddenly, indicating that the well had been stimulated. At the same time the water level response increased suddenly in two near-by monitoring wells. During the second stimulation phase (packer at 1412 m) the well appeared to be stimulated even further. The well eventually produced about 35 l/s with a drawdown of roughly 60 m, and the stimulation had increased the yield of the well by a factor of nearly 60. Thus well SN-12, which appeared to be almost non-productive at the completion of drilling, had turned into a good production well. It is believed that during the stimulation some previously closed fractures, or interbed contacts, reopened connecting well SN-12 to the main fracture system of the geothermal reservoir.

High-temperature hydrothermal systems are physically and chemically zoned with depth. The energy input is from a magmatic zone, intruded by igneous bodies, that may also contribute variable amounts of magmatic fluid to the system. The heat source is directly overlain by a section of rocks, that due to their elevated temperature, respond to stress in a ductile fashion. The ductile zone is, in turn, overlain by a section of rocks that respond to stress in a brittle fashion, where water is able to circulate through fractures (the geothermal reservoir) and will be termed the hydrothermal circulation zone. Ancient and modern high-temperature geothermal systems show a predictable sequence of evolutionary events affecting these stratified zones. Metamorphic core complexes are uplifts, formed in highly extended terrains, that expose fossil brittle-ductile transition zones. Formerly ductile rocks have had brittle fractures superimposed on them, and meteoric hydrothermal systems are associated with the brittle fracturing. Porphyry copper deposits typically evolve from magmatic to meteoric hydrothermal systems. At the Larderello geothermal system, the brittle- ductile transition has been mapped using reflection seismology, and the zone has been penetrated by the San Pompeo 2 well where temperatures >420°C were encountered. Although neo-granitic dikes have been penetrated by …

Well AH-4_bis, at the Ahuachapan Geothermal Field is planned to be drilled on the same pad as the former AH-4. A simulation study was carried out for two casing dameters 13 5/8 and 9 5/8” in order to estimate its production and to know its economic feasibility. The simulation results indcate a high probability of production in the range of 7 Mwe, equivalent to 120 kg/s total mass flow rate, 1250 kJ/kg at 6 bar-a for the new well AH-4_bis. Well AH- 17 is good producer, during 1991 after ten years of production, the well was shut-in due to silica scaling problems. A wellbore simulation was carried out in order to predict the new production conditions after the work-over, mainly to estimate the water flow rate in order to reduce the silica scaling. The results indicate a very low water flow rate. The match between the simulated and measured production curves after the work-over was successful. The well AH-18 is located at the southern part of the actual bore field. CEL is planning to expand the borefield at this area and it is neccessary to estimate the possible production condtions at that zone. The results indicate a high probabilty of …

Previous measurements of acoustic velocities on NEGU- 17 cores indicate that saturation effects are significant enough to cause V_p/V_s anomalies observed in the field. In this study we report on the results of new measurements on core recently recovered from SB-15-D along with some additional measurements on the NEGU-17 cores. The measurements indicate correlations between mechanical, transport, and water storage properties of the matrix which may prove useful for reservoir assessment and management. The SB-15-D material is found to be similar to the NEGU-17 material in terms of acoustic velocities, being characterized by a notably weak pressure dependence on the velocities and a modest V_p/V_s signature of saturation. The effect of saturation on V_p/V_s appears to result in part from a chemo-mechanical weakening of the shear modulus due to the presence of water. Electrical properties of SB-15-D material are qualitatively similar to those of the NEGU-17 cores, although resistivities of SB-15-D cores are notably lower and dielectric permittivities higher than in their NEGU- 17 counterparts. While some limited correlations of measured properties with depth are noted, no clear change in character is observed within SB-15-D cores which can be associated with the proposed cap-rock/reservoir boundary.

A numerical simulation model for the Heber geothermal field in Southern California is being developed under a technology transfer agreement between the Department of Energy/Lawrence Berkeley National Laboratory (LBNL) and the California Department of Conservation, Division of Oil, Gas, and Geothermal Resources (DOGGR). The main objectives of the cooperation are (1) to train DOGGR personnel in the use of the TOUGH2PC computer code; and (2) to develop a module compatible with TOUGH2 to investigate the effects of production/injection operations on the ground surface subsidence-rebound phenomenon observed in the Heber geothermal field. Initial-state calibration (undisturbed system) runs are being conducted to calibrate the model.

Downhole temperature and pressure, mass flow, and enthalpy measurements on three production wells at Kawerau geothermal field are interpretted to illustrate interference effects between these wells. Feed zone locations within the wells, together with geology and chemistry are discussed. Downhole measurements are made in one well while production flow changes are made on another well to monitor pressure transient effects. The interference effects have implications for planning future production drilling.

This paper describes the design, construction, and preliminary results of an experiment that studies imbibition displacement in two fracture blocks. Three core configurations were constructed. The configurations are a compact core, a two-block system with a 1 mm spacer between the blocks, and a two-block system with no spacer. The blocks are sealed in epoxy so that saturation measurements can be made throughout the displacement experiments using a Computed Tomography (CT) scanner. Preliminary results are presented from a water/air experiment. These results suggest that it is incorrect to assume negligible capillary continuity between matrix blocks as is often done.

The Tiwi geothermal field is located in southern Luzon on the northeast flank of Mt. Malinao, an andesitic volcano that was active 0.5 to 0.06 Ma. Matalibong-25 (Mat-25) was drilled through the Tiwi reservoir to investigate lithologic and fracture controls on reservoir permeability and to monitor reservoir pressure. Continuous core was collected from 2586.5 to 8000 feet (789 to 2439 meters) with greater than 95% recovery. The reservoir rocks observed in Mat-25 consist mainly of andesitic and basaltic lavas and volcaniclastic rocks above 6600 feet depth (2012 meters) and andesitic sediments below, with a transition from subaerial to subaqueous (marine) deposition at 5250 feet (1601 meters). The rocks in the reservoir interval are strongly altered and veined. Common secondary minerals include chlorite, illite, quartz, calcite, pyrite, epidote, anhydrite, adularia and wairakite. An ³⁹Ar/⁴⁰Ar age obtained on adularia from a quartz-adularia-cemented breccia at a depth of 6066 feet (2012 meters) indicates that the hydrothermal system has been active for at least 320,000 years. Fractures observed in the core were classified as either veins (sealed) or open fractures, with the latter assumed to represent fluid entries in the geothermal system. Since the core was not oriented, only fracture frequency and dip angle …

A closed-loop circulation test was conducted from 10 May to 14 July 1995 on the Hot Dry Rock (HDR) reservoir at Fenton Hill, New Mexico after a hiatus of nearly two years. Changes in heat transfer and reservoir volume were investigated and compared to previous circulation tests. Chemical tracers can be used to measure the volume of flow paths in hydrologic systems. Usually, tracers are used in low temperature situations, but the application to high temperature systems has been established for certain tracer compounds. During the 1995 flow testing at Fenton Hill, both a conservative and a non conservative tracer were injected into the reservoir in each of two separate experiments. The purpose was to determine the volume of the most direct flow paths and to estimate the total volume of fractures in the system. The results indicate a relatively static reservoir volume between June and July, yet with an increase in flow dispersion. It can be assumed that channeling of flow did not occur in the main body of the reservoir due to continuous operation. However, a new flow path adjacent to the injection well did develop, and its affect on reservoir flow was investigated using tracer technology. The …

Core flooding experiments on argillaceous sandstone are carried out showing that for high injection flow rates permeability reduction occurs. The decrease of permeability is a consequence of the migration of insitu particles. Two models are used to simulate the observed phenomena. The so-called network model is able to give insight in the physics behind the particle migration. The other model based on mass balance and constitutive laws is used for quantitative and qualitative comparison with the experiments.

We report on continuing experimental and numerical efforts to obtain steam-water relative permeability functions and to assess effect of heat transfer and phase change. To achieve these, two sets of steady-state flow experiments were conducted: one with nitrogen and water and another with steam and water. During these experiments, a mixture of nitrogen-water (or steam-water) was injected into a Berea sandstone core. At the onset of steady state conditions, three-dimensional saturation distributions were obtained by using a high resolution X-ray computer tomography scanner. By identifying a length of the core over which a flat saturation profile exists and measuring the pressure gradient associated with this length, we calculated relative permeabilities for nitrogen-water flow experiments. The relative permeability relations obtained in this case were in good agreement with those reported by other investigators. Another attempt was also made to conduct a steam-water flow experiment under adiabatic conditions. This experiment was completed with partial success due to the difficulties encountered during the experiment. The results of this experiment showed that a flat saturation profile actually developed over a substantial length of the core even at a comparatively modest injection rate (6 grams per minute) with low steam quality (4% by mass). The …

Theoretical calculations have been performed to estimate the electrical generating capacities of small-diameter geothermal wells for off-grid rural electrification using wellhead generators. In these applications, generating capacities of interest are typically in the range 100-1000 kWe. The approach amounted to (1) calculating the “wellhead discharge characteristics” (water/steam discharge rates as functions of wellhead pressure) for a variety of hypothetical well and reservoir descriptions, (2) employing a mathematical representation for the net generating capacity of a wellhead powerplant as a function of its operating inlet pressure and steam inlet rate, and (3) varying the wellhead (= turbine inlet) pressure to identify the “optimum” pressure value at which the net electrical power is maximized. Calculations were carried out for well diameters from 75 mm to 300 mm, for well depths from 300 to 1200 meters, for reservoir temperatures from 100°C to 240°C, for piezometric surface depths (related to shut-in reservoir pressure) from zero to 250 meters, and for downhole productivity indices from 2 kg/s/bar to infinity. A few cases were also included in which the CO₂ content of the reservoir fluid was non-zero (up to 1% by mass in the brine). Both backpressure and condensing single-flash steam turbine powerplants were considered. The …

A solid waste is classified as hazardous if it contains sufficient leachable components to contaminate the groundwater and the environment if disposed in a landfill. Scale, sludge and drilling mud from three geothermal fields (Bulalo, Phlippines; Cerro Prieto, Mexico; and Dixie Valley, USA) containing regulated elements at levels above the earth‘s crustal abundance were studied for their leachability. Cr, As, Cu, Zn and Pb were detected at levels which could impair groundwater quality if leaching occurred. Several procedures were used to assess the likely risk posed by the residues : protocol leaching tests (Canadian LEP and US TCLP), toxicity testing, accelerated weathering test, and a preliminary acid mine drainage potential test. Whole rock analysis, X-ray diffraction, and radioactivity counting were also performed to characterize the samples. Toxi-chromotest and SOS-chromotest results were negative for all samples. Leachng tests indicated that all of them could be classified as nonhazardous wastes. Only one of the six showed a low-level radioactivity based on its high Pb-210 activity. Initial tests for acidification potential gave positive results for three out of six samples whle none of the regulated elements were found in the leachate after accelerated weathering experiment for three months.

A recent 6-day flow experiment conducted at the Los Alamos National Laboratory's Fenton Hill Hot Dry Rock (HDR) test site in north-central New Mexico has verified that an HDR reservoir has the capability for a significant, and very rapid, increase in power output upon demand. The objective of this cyclic load-following experiment was to investigate the performance of the reservoir in a nominal high-backpressure (2200 psi) baseload operating condition upon which was superimposed greatly increased power production for a 4-hour period each day. In practice, this enhanced production was accomplished by dropping the production well backpressure from the preexisting level of 2200 psi down to about 500 psi to rapidly drain the fluid stored in the pressure-dilated joints surrounding the production well. During the last cycle of this six-cycle test, the mean production conditions were 146.6 gpm for 4 hours at a temperature of 189°C followed by 92.4 gpm for 20 hours at a temperature of 183°C. These flow and temperature values indicate a flow enhancement of 59%, and a power enhancement of 65% during the high-production period. The time required to increase the reservoir power output from the baseload to the peaking rate was about 2 minutes.

A numerical model for geothermal reservoir has been developed. The model used is based on an idealized, two-dimensional case, where the porous medium is isotropic, nonhomogeneous, filled with saturated liquid. The fluids are assumed to have constant and temperature dependent viscosity. A Boussinesq approximation and Darcy’s law are used. The model will utilize a simple hypothetical geothermal system, i.e. graben within horsts structure, with three layers of different permeabilities. Vorticity plays an importance roles in the natural convection process, and its generation and development do not depend only on the buoyancy, but also on the magnitude and direction relation between the flow velocity and the local gradient of permeability to viscosity ratio. This model is currently used together with a physical, scaled-down reservoir model to help conceptual modeling.

This paper presents recent results of an investigation on failure mode and wear of rock-bits used to drill geothermal wells located in the area of Larderello (Italy). A new wear mechanism, conceived from drilling records and dull bit evaluation analysis, has been identified and a particular configuration of rock-bit has been developed and tested in order to reduce drilling costs. The role of high Bottom Hole Temperature (BHT) on rock-bit performances seems not yet very well understood: so far, only drillability and formation abrasiveness are generally considered to account for poor drilling performances. In this paper, the detrimental effects of high BHT on sealing and reservoir system of Friction Bearing Rock-bits (FBR) have been investigated, and a new bearing wear pattern for FBR's run in high BHT holes has been identified and further verified via laboratory inspections on dull bits. A novel interpretation of flat worn cutting structure has been derived from the above wear pattern, suggesting the design of a particular bit configuration. Test bits, designed in the light of the above criteria, have been prepared and field tested successfully. The paper reports the results of these tests, which yielded a new rock-bit application, today considered as a standad …

Geothermal resources have been classified into low, intermediate and high enthalpy resources by their reservoir temperatures. The temperature ranges used are arbitrary and there is not a general agreement. Geothermal resources should be classified by two independent thermodynamic properties of their fluids at the wellhead. They should reflect the fluids availability to do work. By setting the triple point of water as the sink condition, and normalising the fluids specific exergies by the maximum specific exergy of dry saturated steam, geothermal resources can be classified into high, medium, and low category resources by their specific exergy indices (SEI) of greater than 0.5, between 0.05 and 0.5, and less than 0.05. These correspond to geothermal fluids having exergies greater than that of dry saturated steam at 1 bar absolute, between saturated water and dry saturated steam at 1 bar absolute, and less than saturated water at 1 bar absolute respectively.

The Kakkonda geothermal field is known as a unique field such that a new reservoir was found at about 2500 m in depth after the shallow reservoir ranging from 1000 m to 1500 m had been produced for about eight years. The shallow reservoir is composed of sedimentary rock with igneous rock intrusions, while the deep reservoir is a fractured thin zone located at the top of a large granite intrusion. Between the two, there exist thermally metamorphosed zones. This study aims at integrated interpretation of the top structural surface of the deep reservoir. The data used include well data, microearthquakes, and several metamorphic minerals. Microearthquakes, which are continuously observed at surface, reflect the structural surface of the granite intrusion of the deep reservoir. The metamorphic minerals such as biotite and cordierite caused by strong heat conduction out of the granite also give an image of the structure. Based on the spacings of acoustic emission data, images of the structural surface are extracted statistically. The degree of uncertainty is evaluated. The isograds of the metamorphic mineral distributions are reproduced by a regional heat conduction model.

The chloride and CO₂ chemistry at the Wairakei geothermal field, New Zealand has been modelled using an extended version of the geothermal simulator TOUGH2 which solves the equations for the transport of reacting chemical species in multi-phase fluids. Reactions involving the speciation of aqueous CO₂ to H₂CO₃ and HCO₃^-, are included in the model. Because CO₂ speciation in water is pH dependent, a reaction involving the most important weak acid buffer at Wairakei (H₄SiO₄) has also been included. A ‘Henry’s Law’ reaction expresses the equilibrium between the aqueous and vapour components of CO₂. The chloride is treated as a conservative, non-reacting species which is present only in the liquid phase. Results from the model are compared with measured chloride and CO₂ data from Wairakei covering the period 1959 to 1987.

In July 1995 in the course of the Hot Dry Rock (HDR) site investigation studies in Soultz s.F. (France) multi rate hydraulic injection tests were conducted in the borehole GPK2. The downhole pressure records obtained from the lowermost depth domain between 3211 m and 3876 m demonstrate non-laminar hydraulic behavior. Such behavior was also observed earlier during a similar set of flow step tests in the GPKl borehole Soultz. Like the analysis of these earlier data sets, it could be shown that the pressure records from July 1995 are corresponding to empirical flow laws established for non-laminar hydraulic regimes. In this study a numerical model is described which is being developed for the analysis of non-laminar flow in fractures. Similar models have already been applied to production and injection tests at GPK1. The results show that the observed transient pressure record is well predicted by such a non-linear flow law. Conventional laminar flow models cannot reproduce these curves. An evaluation of the parameters resulting from both, steady state and transient analysis leads to assumptions on the geometry of the main fracture system. Our calculations show that surface areas above 0.05 km² and apertures in the order of 0.4 mm results …

Kamojang Geothermal Field is one of the best geothermal field in the world, explored since 1918. The field lies 33 km south-east Bandung, West Java. It is located in the centre of a volcanic chain which has progressively grown from WSW to ENE. Three tectonic activities have created current Kamojang structures. Firstly, the circular collapse of Pangkalan, 2 km in diameter whch occupies the central part of the Kamojang field; secondly, NE -SW flults of tensional and lateral origin, are parallel to the magmatic axis; and last, 5 km wide graben is a major expression of NW-SE tensional faults. The faults, having N60 strike in the southeastern part of the field have been identified as a very important structures related to the main target of reservoir Kamojang field. Even if the faults and fractures have been altered in the upper part of the surface and form non permeable seals, the bottom sections may still be highly permeable. Therefore for development drilling one must consider the deep structures instead of just shallow expressions and alteration. Geological correlations between the several wells drilled up to date shows evidence that the structures correspond to the surface features as described above. Case study of …

Since 1985, NEDO has advanced a]Hot Dry Rock project in Hijiori, Japan. Circulation tests have been performed in FY1991 (in a shallow reservoir), and in FY1995 (in both shallow and deep reservoirs). In 1991 circulation test, the result was that 78% fluid recovery at an injection rate of 60 tons/hour and production temperatures of 150 °C - 190 °C . However no detailed analysis of flow conditions was given. Therefore, a simplified HDR model has been proposed to understand the Hijion HDR reservoir. We have analyzed the 1991 circulation test using the model. This study is very important for analyzing the circulation test in both of shallow and deep reservoir which was conducted in 1995. This paper summarizes the 1991 circulation test at the Hijiori HDR test site, and estimation of the reservoir fluid storage by using "unrecovered" flow from the new conceptual idea of HDR reservoir model.