A tank investigation has been conducted on a 1/8-size powered dynamic model of the Grumman JRF-5 airplane equipped with twin hydro-skis. The results of tests using two types of skis are presented: one had vertical sides joining the top surface to the chine; the other had the top surface faired to the chine to eliminate the vertical sides. Both configurations had satisfactory longitudinal stability although the model had a slightly greater stable elevator range available when the skis without the vertical sides were attached. Free model tests indicated no instability present when one ski emerged before the other. Considerable excess thrust was available at all speeds with either type of skis. A hump gross load-resistance ratio of 3.37 was obtained with the skis with the vertical sides and 3.53 with the other skis. Landing behavior in smooth water with yaw up to 15deg and roll up to 15deg in opposite directions was satisfactory with either type of skis.

Report presenting an experimental investigation of the pressures induced on a flat plate by a propulsive jet exhausting from sonic and supersonic nozzles at a free-stream Mach number of 1.80. Measurements of the pressure distribution on a flat-plate wing were made at zero angle of attack for four different locations of the jet exhaust nozzle beneath the wing. Results regarding the jet-off pressure coefficients, jet-on pressure coefficients, and incremental pressure coefficients are provided.

Report presenting testing of a model of an airplane configuration with thin, highly tapered, 45 degree sweptback surfaces at a range of Mach numbers to obtain the lateral stability characteristics of the configuration. Results regarding the time history, trim characteristics, lateral-force derivative, vector plots, and downwash and sidewash are provided. At Mach number 1.3, the model experienced a violent combined lateral-longitudinal motion and large angles of sideslip and attack with large rolling velocities.

"Wind-tunnel tests of a full-scale model of the Republic XP-91 airplane were conducted to determine the longitudinal and lateral characteristics of the wing alone and the wing-fuselage combination, the characteristics of the aileron, and the damping in roll of the wing alone. Various high-lift devices were investigated including trailing-edge split flaps and partial- and full-span leading-edge slats and Krueger-type nose flaps. Results of this investigation showed that a very significant gain in maximum lift could be achieved through use of the proper leading-edge device" (p. 1).

From Summary: "Two improvements have been made in the method developed in NACA Reports nos. 487 and 591 for the estimation of the inflow velocity required to overcome a given decelerating torque in an autogiro rotor. At low tip-speed ratios, where the assumptions necessary for the analytical integrations of the earlier papers are valid, the expressions therein derived are greatly simplified by combining and eliminating terms with a view of minimizing the numerical computations required. At high tip-speed ratios, by means of charts based on graphical integrations, errors inherent in the assumptions associated with the analytical method are largely eliminated."

This report presents test results of experiments on the vibration-response characteristics of airplane structures on the ground and in flight. It also gives details regarding the construction and operation of vibration instruments developed by the National Advisory Committee for Aeronautics.

"This paper deals with the analysis of 2-spar cantilever wings in torsion, taking cognizance of the fact that the spars are not independent, but are interconnected by ribs and other structural members. The principles of interaction are briefly explained, showing that the mutual relief action occurring depends on the "pure torsional stiffness" of the wing cross section. Various practical methods of analysis are outlined" (p. 45).

In this report it is shown that the shear, axial force, and moment at one point in a simple ring subjected to any loading condition can be given by three independent equations involving certain integrals that must be evaluated regardless of the method of analysis used. It is also shown how symmetry of the ring alone or of the ring and the loading about 1 or 2 axes makes it possible to simplify the three equations and greatly reduces the number of integrals that must be evaluated. Application of the general equations presented in this report to practical problems in the stress analysis of rings makes it possible to shorten, simplify, and systematize the calculations for both simple and braced rings. Three illustrative problems are included to demonstrate the application of the general equations to a simple ring with different loadings.

This report presents the results of wind tunnel tests on a Robinson-type anemometer. The investigation covered force measurements on individual cups, as well as static and dynamic torque measurements and calibrations on complete cup wheels. In the tests on individual cups 5 cup forms were used and in the measurements on complete cup wheels 4 cup wheels with 3 arm lengths for each cup wheel were tested. All the results are presented in graphical form.

This report presents the results of an investigation to study the effect of water vapor upon the spatial speed of flame in equivalent mixtures of carbon monoxide and oxygen at various total pressures from 100 to 780 mm.hg. These results show that, within this pressure range, an increase in flame speed is produced by increasing the mole fraction of water vapor at least as far as saturation at 25 degrees c., and that the rate of this increase is greater the higher the pressure. It is evident that water vapor plays an important part in the explosive oxidation of carbon monoxide; the need for further experimental evidence as to the nature of its action is indicated.

This investigation is a detailed description of the soap-bubble, or constant-pressure, method as applied to the explosive oxidation of carbon monoxide. A series of values of the speed of flame in space in various mixtures of CO and O2 containing a constant percentage of water vapor was obtained by the constant-volume method. These results served as a guide in the perfection of the soap-bubble method.

This report gives the results of an investigation conducted in the NACA full-scale wind tunnel on a small parasol monoplane equipped with three different split trailing-edge wing flaps. The object of the investigation was to determine and correlate data on the characteristics of the airplane and flaps as affected by variation in flap chord, flap deflection, and flap location along the wing chord. The results give the lift, the drag, and the pitching moment characteristics of the airplane, and the flap forces and moments, the pressure distribution over the flaps and wing at one section, and the downwash characteristics of the flap and wing combinations.

The object of the investigation presented in this report was to determine the effects of increasing the air charge and scavenging the clearance volume of a 4-stroke-cycle compression-ignition engine having a vertical-disk form combustion chamber. Boosting the inlet-air pressure with normal valve timing increased the indicated engine power in proportion to the additional air inducted and resulted in smoother engine operation with less combustion shock. Scavenging the clearance volume by using a valve overlap of 145 degrees and an inlet-air boost pressure of approximately 2 1/2 inches of mercury produced a net increase in performance for clear exhaust operation of 33 percent over that obtained with normal valve timing and the same boost pressure. The improved combustion characteristics result in lower specific fuel consumption, and a clearer exhaust.

This report presents the results of wind tunnel tests on various auxiliary airfoils having three different airfoil sections and several different chord lengths in combination with a Clark Y model wing in a sufficient number of relative positions to determine the optimum with regard to certain criterions of aerodynamic performance. The airfoil sections included a symmetrical profile, one of medium camber, and a highly cambered one. The chord sizes of the auxiliary airfoils ranged from 7.5 to 25 percent of the chord of the main wing, and the span was equal to that of the main wing.

"This report is the second of a series presenting the results of strength tests of thin-walled duralumin cylinders and truncated cones of circular and elliptic section. It contains the results obtained from compression tests on 45 thin-walled duralumin cylinders of circular section with ends clamped to rigid bulkheads. In addition to the tests on duralumin cylinders, there are included the results of numerous tests on rubber, celluloid, steel, and brass cylinders obtained from various sources" (p. 585).

"The investigation of the effect of mass distribution on the spinning of airplanes initiated with tests on the NY-1 airplane has been continued by tests on another airplane in order to increase the scope of the information and to observe particularly the behavior of an airplane that shows considerable change in sideslip angle for its various conditions of spinning. The XN2Y-1 naval training biplane was used for the present tests in which changes of ballast along the longitudinal and lateral axes and changes of aileron, stabilizer, and elevator settings were made. The effects of these changes on the steady spin were measured in flight' (p. 185).

Models of the Hermes A-3B missile were tested in the Ames supersonic free-flight wind tunnel to determine the static-longitudinal-stability characteristics at a Mach number of 5.0 and a Reynolds number based on body length of 10 million. The results indicated that the model center of pressure was 45.3 percent of the body length aft of the nose and the lift-curve slope based on body frontal area was 0.064 per degree. Estimates indicated that the effect on these characteristics of aeroelastic twisting of the model fins was small but important if a precise location of center of pressure is required. A comparison of the test results with predictions based on available theory showed that the theory was useful only for rough estimates, The drag coefficient at zero lift, based on body frontal area, was found to be 0.155.

Tests were conducted in order to determine how the characteristics of a propeller are affected by cutting off the tips. The diameter of a standard 10-foot metal propeller was changed successively to 9 feet 6 inches, 9 feet 0 inches, 8 feet 6 inches, and 8 feet 0 inches. Each propeller thus formed was tested at four pitch settings using an open cockpit fuselage and a D-12 engine. A small loss in propulsive efficiency is indicated. Examples are given showing the application of the results to practical problems.

"This report is the first in a series in which it is intended to compare the relative merits of all ordinary and some special forms of ailerons and other lateral control devices in regard to their effect on lateral controllability, lateral stability, and airplane performance. The comparisons are based on wind-tunnel test data, all the control devices being fitted to model wings having the same span, area, and airfoil section, and being subjected to the same series of force and rotation tests. The results are given for five different aileron movements: one with equal up-and-down deflection, one with average and one with extreme differential motion, one with upward deflection only, and one with the ailerons arranged to float with respect to the wing" (p. 357).

This report presents the results of an investigation of the rolling and yawing moments due to ailerons of various chords and spans on two airfoils having the Clark Y and U. S. A. 27 wing sections. Some attention is devoted to a study of the effect of scale on rolling and yawing moments and to the effect of slightly rounding the wing tips. The results apply to level flight with the wing chord set at an angle of attack of +4 degrees and to conditions of zero pitch, zero yaw, and zero roll of the airplane. It is planned later to extend the investigation to other attitudes for monoplane and biplane combinations. The work was conducted in the 10 foot wind tunnel of the Bureau of Standards on models of 60-inch span and 10-inch chord. (author).

"Additional results on the static longitudinal and lateral stability characteristics of a 0.05-scale model of the Convair F2Y-1 water-based fighter airplane were obtained in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.50 to 0.92. The maximum angle-of-attack range (obtained at the lower Mach numbers) was from -2 degrees to 25 degrees. The sideslip-angle range investigated was from -4 degrees to 12 degrees" (p. 1).

Report presenting the static-thrust characteristics of the NACA 8.75-(5)(05)-037 dual-rotation propeller with six and eight blades as obtained on the static test stand in the course of an investigation set up primarily for studying blade vibratory stresses. Force data were obtained for a blade-angle range measured at the 0.75 radial station on the front propeller. Results regarding the effect of tip Mach number, effect of number of blades, and effect of blade angle are provided.

Report presenting aerodynamic-heating data obtained on a modified-fineness-ratio-5.0 Von Karman nose shape at free-stream Mach numbers up to 10.4 with a rocket-propelled model. Transient skin temperatures were measured on the nose, and a maximum temperature of 1,663 degrees R was measured after maximum Mach number was obtained.