A statistics-based model is being developed to predict the laser-damage-limited lifetime of UV optical components on the NIF laser. In order to provide data for the model, laser damage experiments were performed on the Beamlet laser system at LLNL. An early prototype NIF focus lens was exposed to twenty 35 1 nm pulses at an average fluence of 5 J/cm{sup 2}, 3ns. Using a high resolution optic inspection system a total of 353 damage sites was detected within the 1160 cm{sup 2} beam aperture. Through inspections of the lens before, after and, in some cases, during the campaign, pulse to pulse damage growth rates were measured for damage initiating both on the surface and at bulk inclusions. Growth rates as high as 79 {micro}m/pulse (surface diameter) were observed for damage initiating at pre-existing scratches in the surface. For most damage sites on the optic, both surface and bulk, the damage growth rate was approximately l0{micro}m/pulse. The lens was also used in Beamlet for a subsequent 1053 {micro}m/526 {micro}m campaign. The 352 {micro}m-initiated damage continued to grow during that campaign although at generally lower growth rate.

This report documents the systems and component requirements, design approaches, and performance and design characteristics for the 5-kwe system.

This document provides an evaluation and recommendations for radiological workplace air monitoring and response to ventilation failure for the Critical Mass Laboratory, 209-E Building. The Critical Mass Laboratory, part of the 209-E Building, was designed to provide a heavily shielded room where plutonium and uranium liquid solutions could be brought into various critical configurations under readily controlled and monitored conditions. The facility is contained within a one-story L-shaped concrete block and reinforced concrete building. One wing houses offices, a control room, shops, and a common area while the other wing includes an equipment room, the change room, work areas, and the two-story Critical Assembly Room (CAR). Three of the rooms contain radiologically contaminated equipment and materials.

This is a Report of a study that has been made Nak cooled reactor containing 199 ZrH-UO2 fuel elements to determine thermal-hydraulic characteristics of the core bundle, It contains nominal operating power of the reactor is 300kwt with the Nak existing from the core at 1200 F.

The Gordon Research Conference on Organometallic Chemistry was held at Salve Regina University, Newport, Rhode Island, July 22-27, 2001. The conference had 133 participants. The attendees represented the spectrum of endeavor in this field, coming from academia, industry, and government laboratories, and included US and foreign scientists, senior researchers, young investigators, and students. Emphasis was place on current unpublished research and discussion of the future target areas in this field. There was a conscious effort to stimulate lively discussion about the key issues in the field today. Time for formal presentations was limited in the interest of group discussions; poster sessions were held.

Topics covered in this GRC include high-resolution spectroscopy, coherent electronic energy transport in biology, excited state theory and dynamics, excitonics, electronic spectroscopy of cold and ultracold molecules, and the spectroscopy of nanostructures. Several sessions will highlight innovative techniques such as time-resolved x-ray spectroscopy, frequency combs, and liquid microjet photoelectron spectroscopy that have forged stimulating new connections between gas-phase and condensed-phase work.

The mechanical behavior of materials with small dimension(s) is of both fundamental scientific interest and technological relevance. The size effects and novel properties that arise from changes in deformation mechanism have important implications for modern technologies such as thin films for microelectronics and MEMS devices, thermal and tribological coatings, materials for energy production and advanced batteries, etc. The overarching goal of the 2012 Gordon Research Conference on "Thin Film and Small Scale Mechanical Behavior" is to discuss recent studies and future opportunities regarding elastic, plastic and time-dependent deformation, as well as degradation and failure mechanisms such as fatigue, fracture and wear. Specific topics of interest include, but are not limited to: fundamental studies of physical mechanisms governing small-scale mechanical behavior; advances in test techniques for materials at small length scales, such as nanotribology and high-temperature nanoindentation; in-situ mechanical testing and characterization; nanomechanics of battery materials, such as swelling-induced phenomena and chemomechanical behavior; flexible electronics; mechanical properties of graphene and carbon-based materials; mechanical behavior of small-scale biological structures and biomimetic materials. Both experimental and computational work will be included in the oral and poster presentations at this Conference.

The current status of the 2mrad crossing angle layout for the ILC is reviewed. The scheme developed in the UK and France is described and the performance discussed for a TeV machine. Secondly, the scheme developed at SLAC and BNL is then studied and modified for a TeV machine. We find that both schemes can handle the higher energy beam with modifications, and share many common features.

This Acceptance Test Plan (ATP) will document the satisfactory operation of the corrosion probe cabinets destined for installation on tanks 241-AN-102 and 241-AN-107. This ATP will be performed by the manufacturer on each cabinet prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion monitoring cabinets to be installed on tanks 241-AN-102 and 241-AN-107. One cabinet will be installed on each tank. Each cabinet will contain corrosion monitoring hardware to be connected to existing corrosion probes already installed in each tank. The test will consist of a continuity test of the cabinet wiring from the end of cable to be connected to corrosion probe, through the appropriate intrinsic safety barriers and out to the 15 pin D-shell connectors to be connected to the corrosion monitoring instrument. Additional testing will be performed using a constant current and voltage source provided by the corrosion monitoring hardware manufacturer to verify proper operation of corrosion monitoring instrumentation (input a known signal and see if the instrumentation records the proper value).

High resolution spectroscopy experiments with visible adaptive optics (AO) telescopes at Starfire Optical Range and Mt. Wilson have demonstrated that spectral resolution can be routinely improved by a factor of - 10 over the seeing-limited case with no extra light losses at visible wavelengths. With large CCDs now available, a very wide wavelength range can be covered in a single exposure. In the near future, most large ground-based telescopes will be equipped with powerful A0 systems. Most of these systems are aimed primarily at diffraction-limited operation in the near IR. An exciting new opportunity will thus open up for high resolution IR spectroscopy. Immersion echelle gratings with much coarser grooves being developed by us at LLNL will play a critical role in achieving high spectral resolution with a compact and low cost IR cryogenically cooled spectrograph and simultaneous large wavelength coverage on relatively small IR detectors. We have constructed a new A0 optimized spectrograph at Steward Observatory to provide R = 200,000 in the optical, which is being commissioned at the Starfire Optical Range 3.5m telescope. We have completed the optical design of the LLNL IR Immersion Spectrograph (LISPEC) to take advantage of improved silicon etching technology. Key words: adaptive …

This paper shows an analysis of the applicability of an adsorption system for electric vehicle (EV) air conditioning. Adsorption systems are designed and optimized to provide the required cooling for four combinations of vehicle characteristics and driving cycles. The resulting adsorption systems are compared with vapor compression air conditioners that can satisfy the cooling load. The objective function is the overall system weight, which includes the cooling system weight and the weight of the battery necessary to provide energy for air conditioner operation. The system with the minimum overall weight is considered to be the best, because a lower weight results in an increased vehicle range. The results indicate that, for the conditions analyzed in this paper, vapor compression air conditioners are superior to adsorption systems not only because they are lighter, but also because they have a higher COP and are more compact.

This document details information provided in support of AECOP Task Assignment No. 5, ``Conversion of Np-237 to Pu-238.`` Conversion efficiency of each production reactor for a range of product purities and for the anticipated range of available flux levels is given.

Hot rolling is a problem involving large deformations during the process of turning an ingot into a thin sheet. As a result of the large deformations inherent in the process, significant amounts of energy are put into the ingot mechanically, most of which results in heat generation. Therefore, in order to predict the results of rolling both the mechanical and the thermal factors must accurately represent the real conditions. The factors which must be properly tuned include interface friction, mass scaling to decrease computation times, heat transfer at the interface, convective heat transfer from the ingot, and convective heat transfer from the roll. Since these parameters are generally not measurable the correct values must be derived by tuning the parameters so that solutions match some other measurable result. The interface friction will be tuned using an ALE3D input deck which has been set up to output the torque applied to the roll during the pass. The friction coefficient will be adjusted so that the computed torque matches the measured value. The various heat transfer coefficients are dependent on each other, and are tuned based on measured roll surface temperatures, ingot exit temperatures, and the energy input through the mechanical deformation …

Horizontal flying wire measurements give beam profiles from which information about the beam momentum distribution and betatron distribution can be extracted. When calculating these beam characteristics in the past, for the matter of simplicity, the beam has been assumed Gaussian. For beam profiles which may not be Gaussian, an algorithm to obtain the general beam momentum distribution is developed using the Fourier transform to the beam profiles. Since the profile is the convolution of the momentum distribution and the betatron distribution, using a Fourier transform method makes calculations easier. 6 figs.

The interplay of the effects of geometry and collective motion on d-{alpha} correlation functions is investigated for central Xe+Au collisions at E/A=50 MeV. The data cannot be explained with out collective motion, which could be partly along the beam axis. A semi-quantitative description of the data can be obtained using a Monte -Carlo model, where thermal emission is superimposed on collective motion. Both the emission volume and the competition between the thermal and collective motion influence significantly the shape of the correlation function, motivating new strategies for extending intensity interferometry studies to massive particles.

This paper considers an approach for representing nuclear data that is qualitatively different from the approach currently adopted by the nuclear science community. Specifically, they examine a representation in which complicated data is described through collections of distinct and self contained simple data structures. This structure-based representation is compared with the ENDF and ENDL formats, which can be roughly characterized as dictionary-based representations. A pilot data representation for replacing the format currently used at LLNL is presented. Examples are given as is a discussion of promises and shortcomings associated with moving from traditional dictionary-based formats to a structure-rich or class-like representation.

This paper discusses the merits of differing strategies that the Department of Energy might care to adopt for developing a broader consensus within the United States on whether the US should proceed with a major program on actinide burning and if so, in what manner.

This paper shows an analysis of the applicability of an adsorption system for electric vehicle (EV) air conditioning. Adsorption systems are designed and optimized to provide the required cooling for four combinations of vehicle characteristics and driving cycles. The resulting adsorption systems are compared with vapor compression air conditioners that can satisfy the cooling load. The objective function is the overall system weight, which includes the cooling system weight and the weight of the battery necessary to provide energy for air conditioner operation. The system with the minimum overall weight is considered to be the best. The results show the optimum values of all the variables, as well as temperatures and amounts adsorbed, for the adsorption and desorption processes. The results indicate that, for the conditions analyzed in this paper, vapor compression air conditioners are superior to adsorption systems, not only because they are lighter, but also because they have a higher COP and are more compact.

Our objectives are to develop a new integrative physiological-morphological model of the wheat crop that will behave realistically in high-CO[sub 2] environments, and to update the ALFALFA model to match the wheat model's photosynthetic structures and microclimates.

Our objectives are to develop a new integrative physiological-morphological model of the wheat crop that will behave realistically in high-CO{sub 2} environments, and to update the ALFALFA model to match the wheat model`s photosynthetic structures and microclimates.

In this paper we discuss the application of a new diagnostic tool for analysis of flame simulations. This methodology is based on following specific chemical elements, e.g., carbon or nitrogen, as they move through the system. From this perspective an ''atom'' is a component of a molecule that is being transported through the simulation domain by advection and diffusion. Reactions cause the atom to shift from one species to another with the subsequent transport of the atom determined by the movement of the new species.

The Single Heater Test (SHT) is the first of three in-situ thermal tests included in the site characterization program for the potential nuclear waste monitored geologic repository at Yucca Mountain. The heating phase of the SHT started in August 1996 and was concluded in May 1997 after 9 months of heating. Cooling continued until January 1998, at which time post-test characterization of the test block commenced. Numerous thermal, hydrological, mechanical, and chemical sensors monitored the coupled processes in the unsaturated fractured rock mass around the heater (CRWMS M&O 1999). The objective of this calculation is to benchmark a numerical simulation of the rock mass thermal behavior against the extensive data set that is available from the thermal test. The scope is limited to three-dimensional (3-D) numerical simulations of the computational domain of the Single Heater Test and surrounding rock mass. This calculation supports the waste package thermal design methodology, and is developed by Waste Package Department (WPD) under Office of Civilian Radioactive Waste Management (OCRWM) procedure AP-3.12Q, Revision 0, ICN 3, BSCN 1, Calculations.

Although there were the ususl fluctuations in background at certain of the monitoring stations, the contamination levels recorded do not differ significantly from those of the previous year except that there appears to be a slight trend downward. Data are tabulated. This downward trend can be attributed to a curtailment of operations at the Laboratory, the gradual implementation of the containment program, and a curtailment in world-wide weapons testing. Tall-out data are included. Two personnel exposures were recorded which have been reported elsewhere. One emPloyee received a relatively high exposure to the left hand which consisted primarily of soft radiation. A second employee apparently has accumulated a sizeable fraction of a permissible body burden of Pu/sup 239/. The number of unusual occurrences increased over the previous year. However, in general, these events posed only routine problems and it is probable that the noted increase in such occurrences is due primarily to a more complete reporting system which was inaugurated early in the year. (auth)

Oil based aerosol ``Smoke`` commonly used for testing the efficiency and penetration of High Efficiency Particulate Air filters (HEPA) and HEPA systems can produce flammability hazards that may not have been previously considered. A combustion incident involving an aerosol generator has caused an investigation into the hazards of the aerosol used to test HEPA systems at Hanford.