A 0.4 mm submillimeter-wave, phase-modulated polarimeter/interferometer is used for simultaneous time-dependent measurement of line-averaged electron density and poloidal field-induced Faraday rotation along chords of the plasma column in ISX-B tokamak. Heterodyna detection and hollow dielectric waveguide are utilized to achieve the high sensitivity required for the multichord equipment.

We discuss recent developments in III-V multijunction solar cells, focusing on adding a fourth junction to the Ga0.5In0.5P/GaAs/Ga0.75In0.25As inverted three-junction cell. This cell, grown inverted on GaAs so that the lattice-mismatched Ga0.75In0.25As third junction is the last one grown, has demonstrated 38% efficiency, and 40% is likely in the near future. To achieve still further gains, a lower-bandgap GaxIn1-xAs fourth junction could be added to the three-junction structure for a four-junction cell whose efficiency could exceed 45% under concentration. Here, we present the initial development of the GaxIn1-xAs fourth junction. Junctions of various bandgaps ranging from 0.88 to 0.73 eV were grown, in order to study the effect of the different amounts of lattice mismatch. At a bandgap of 0.88 eV, junctions were obtained with very encouraging {approx}80% quantum efficiency, 57% fill factor, and 0.36 eV open-circuit voltage. The device performance degrades with decreasing bandgap (i.e., increasing lattice mismatch). We model the four-junction device efficiency vs. fourth junction bandgap to show that an 0.7-eV fourth-junction bandgap, while optimal if it could be achieved in practice, is not necessary; an 0.9-eV bandgap would still permit significant gains in multijunction cell efficiency while being easier to achieve than the lower-bandgap junction.

Charged particle exclusive data for high multiplicity U on U events are reported. Analyses are based on comparison with Cugnon's intranuclear cascade model, and the explosion-evaporation simulation of Fai and Randrup. The azimuthal structure of the observed events shows evidence of collective flow. The widely used flow angle methodology proves to be relatively insensitive to collective effects under the conditions of the present experiment. An isotropic pattern of ejectile emission is not reached at maximum multiplicity. 18 refs., 4 figs.

None

Techniques and results of the measurement of the beta-decay rate of the first excited state of /sup 16/N to the ground state of /sup 16/O are reported. Energy levels involved in the decay are shown, and the /sup 16/N 0/sup -/ beta decay branching ration is given. (WHK)

This report is a descriptive summary of the simulation of a free- electron laser Oscillator at Jefferson Lab Lasing in the Vacuum Ultraviolet

The Advanced Light Source (ALS), a dedicated synchrotron radiation facility optimized to generate soft x-ray and vacuum ultraviole (XUV) light using magnetic insertion devices, was proposed by the Lawrence Berkeley Laboratory in 1982. It consists of a 1.3-GeV injection system, an electron storage ring optimized at 1.3 GeV (with the capability of 1.9-GeV operation), and a number of photon beamlines emanating from twelve 6-meter-long straight sections, as shown in Fig. 1. In addition, 24 bending-magnet ports will be avialable for development. The ALS was conceived as a research tool whose range and power would stimulate fundamentally new research in fields from biology to materials science (1-4). The conceptual design and associated cost estimate for the ALS have been completed and reviewed by the US Department of Energy (DOE), but preliminary design activities have not yet begun. The focus in this paper is on the history of the ALS as an example of how a technical construction project was conceived, designed, proposed, and validated within the framwork of a national laboratory funded largely by the DOE.

Sintering behavior of mullite-containing powders was studied over a range of chemical compositions (Al{sub 2}O{sub 3}/SiO{sub 2} ratio). Densification measurements were made for both liquid phase-containing and solid state systems. Small amounts of liquid phase were observed to have a significant effect on densification rate. A linear relationship was obtained between the percent of theoretical density and the logarithm of time for compositions in the range 73-75 wt% Al{sub 2}O{sub 3}. Currently available models for intermediate stage sintering kinetics were considered to be inadequate for these systems. Grain boundary transport 0r diffusion appeared to be the primary mechanism of densification.

At Fermilab, 9-cell 1.3 GHz superconducting RF (SRF) cavities are prepared, qualified, and assembled into cryomodules (CMs) for Project X, an International Linear Collider (ILC), or other future projects. The 1.3 GHz SRF cavity program includes targeted R&D on 1-cell 1.3 GHz cavities for cavity performance improvement. Production cavity qualification includes cavity inspection, surface processing, clean assembly, and one or more cryogenic low-power CW qualification tests which typically include performance diagnostics. Qualified cavities are welded into helium vessels and are cryogenically tested with pulsed high-power. Well performing cavities are assembled into cryomodules for pulsed high-power testing in a cryomodule test facility, and possible installation into a beamline. The overall goals of the 1.3 GHz SRF cavity program, supporting facilities, and accomplishments are described.

Research on the acetylene compound 1,4-diphenylbutadiyne is an effort to develop an air-operative tritium gas scavenger. T/sub 2/ adds to the acetylene bond of the organic in the presence of a metal catalyst. The catalyst also stimulates the oxidation reaction as well. The butadiyne compound has shown good reaction efficiency at 300 ppM T/sub 2/ in static dry air. At this concentration 75% of the scavenged tritium was in the organic. This work has expanded to the investigation of liquid acetylenes, metal acetylene complexes, organometallics and acetylene based alcohols. The best of these compounds has gettered 100% of 10 to 500 ppM T/sub 2/ for both static and dynamic air flow conditions.

A system for fast shaving extraction at 1.5 GeV/c is implemented to extract the circulating beam in five turns. A numerical simulation is first carried out to determine the emittance and the rf structure of the extracted beam. This is followed by several machine study sessions which establish the optimal extraction configuration, confirm the emittance, and modify the transport line for low energy beam. Finally, a one-week run for the Neutrino Oscillation experiment demonstrates that the system is very stable and capable of delivering 7.5 x 10/sup 12/ p/sec with 70% extraction efficiency and 95% transport efficiency.

To demonstrate the feasibility of superconducting RF technology for a high energy e{sup +}/e{sup {minus}} collider, a research and development program has begun with collaborators from Europe, Asia, and North America. The immediate goal of the R&D program is to build and operate a 50 meter-long linac at DESY with 1.3 GHz superconducting RF cavities at a temperature of 1.8 K - 2.0 K and an accelerating gradient of 15 MV/meter. The refrigeration for the test system at DESY initially will have a capacity of about 100 W at 1.8 K, distributed among three test cryostats. In a second step, refrigeration will be upgraded to 200 W at 1.8 K in order to supply the 50 meter test linac. This paper describes the cryogenics of this test system.

The accepted hypothesis is that training quenches are caused by heat generation when conductors move under Lorentz force. Afterwards no conductor motion will occur until a higher field and greater Lorentz force acts. If superior heat transfer and/or greater temperature margin is provided by operating at lower bath temperature, one might expect that the heat generated by conductor motion will not cause a runaway temperature increase, or quench. To test this hypothesis, the central dipole field in SSC model magnets was ramped at 1.8 K to 7.1 tesla without the magnets' quenching. The bath was then raised to 4.4 K and the magnets quenched at their short sample limits of 6.6 tesla or higher. Comparison with similar magnets trained in He I at 4.4 K is made and the significance of the non-quench training on system operation is discussed.

In this paper we derive one space dimensional, reduced systems of equations (1-D closure models) for viscoelastic free jets. We begin with the three-dimensional system of conservation laws and a Maxwell-Jeffreys constitutive law for an incompressible viscoelastic fluid. First, we exhibit exact truncations to a finite, closed system of 1-D equations based on classical velocity assumptions of von Karman. Next, we demonstrate that the 3-D free surface boundary conditions overconstrain these truncated systems, so that only a very limited class of solutions exist. We then proceed to derive approximate 1-D closure theories through a slender jet asymptotic scaling, combined with appropriate definitions of velocity, pressure and stress unknowns. Our nonaxisymmetric 1-D slender jet models incorporate the physical effects of inertia, viscoelasticity (viscosity, relaxation and retardation), gravity, surface tension, and properties of the ambient fluid, and include shear stresses and time dependence. Previous special 1-D slender jet models correspond to the lowest order equations in the present asymptotic theory by an a posteriori suppression to leading order of some of these effects, and a reduction to axisymmetry. Solutions of the lowest order system of equations in this asymptotic analysis are presented: For the special cases of elliptical inviscid and Newtonian free …

A one-D hybrid has been developed to study the start-up of the FRM via neutral-beam injection. The code uses a multi-group numerical model originally developed by J. Willenberg to describe fusion product dynamics in a solenoidal plasma. Earlier we described such a model for use in determining self-consistent ion currents and magnetic fields in FRM start-up. However, consideration of electron dynamics during start-up indicate that the electron current will oppose the injected ion current and may even foil the attempt to achieve reversal. For this reason, we have combined the multi-group ion (model) with a fluid treatment for electron dynamics to form the hybrid code FROST (Field Reversed One-dimensional STart-up). The details of this merger, along with sample results of operation of FROST, are given.

We consider the steady state operation of wall-cooled, fixed-bed tubular reactors. In these reactors the temperature rise ..delta..T must normally be limited to small fractions of the adiabatic temperature rise ..delta..T/sub ad/, both to avoid runaway and maintain product selectivity. Yet ..delta..T/..delta..T/sub ad/ << 1 can only occur if eta = t/sub dif//t/sub reac/ << 1, where t/sub dif/ is the timescale on which heat escapes the reactor by ''diffusing'' to the cooled walls, and t/sub reac/ is the timescale over which the reaction occurs. So here we use asymptotic methods based on eta << 1 to analyze the 2-d reactor equations, and find the radial concentration and temperature profiles to leading order in eta. We then obtain a 1-d model of the reactor by substituting these asymptotically correct profiles into the reactor equations and averaging over r. This model, the ..cap alpha..-model, is identical to the standard (Beek and Singer) 1-d model, except that the reactor's overall heat transfer coefficient U is a decreasing function of the temperature rise ..delta..T. This occurs because as ..delta..T increases, the reaction becomes increasingly concentrated near r = 0, causing a decreased heat transfer efficiency through the reactor's walls. By comparing it with …

We use the heavy quark effective theory to investigate the form factors that describe the semileptonic decays lambda⁺_c -> lambda e⁺ nu, to order 1/m_c. We find that a total of four form factors are needed to this order, in contrast with two form factors to leading order, and six form factors in the most general case. We point out some relationships that arise among the general form factors.

This paper describes electrical design criteria and first operational results a 140 kV, 1 MW average, 11 MW peak, zero-voltage-switching 20 kHz polyphase bridge, boost converter/modulator for klystron pulse application. The DC-DC converter derives the buss voltages from a standard 13.8 kV to 2300 Y substation cast-core transformer. Energy storage and filtering is provided by self-clearing metallized hazy polypropylene traction capacitors. Three ''H-Bridge'' Insulated Gate Bipolar Transistor (IGBT) switching networks are used to generate the polyphase 20 kHz transformer primary drive waveforms. The 20 kHz drive waveforms are chirped the appropriate duration to generate the desired klystron pulse width. PWM (pulse width modulation) of the individual 20 kHz pulses is utilized to provide regulated output waveforms with adaptive feedforward and feedback techniques. The boost transformer design utilizes amorphous nanocrystalline material that provides the required low core loss at design flux levels and switching frequencies. Resonant shunt-peaking is used on the transformer secondary to boost output voltage and resonate transformer leakage inductance. With the appropriate transformer leakage inductance and peaking capacitance, zero-voltage-switching of the IGBT's is attained, minimizing switching losses. A review of these design parameters and the first results of the performance characteristics will be presented.

This conference paper describes the GaInAsN cells that are measured to retain 933% and 894% of their original efficiency after exposure to 5 X 1014 and 1 X 1015 cm-2 1-MeV electrons, respectively. The rate of degradation is not correlated with the performance at beginning of life (BOL). The depletion width remains essentially unchanged, increasing by&lt; 1%. Temperature-coefficient data for GaInAsN cells are also presented. These numbers are used to project the efficiency of GaInAsN-containing multijunction cells. The GaInAsN junction is not currently predicted to increase the efficiencies of the multijunction cells. Nevertheless, GaInAsN-containing multijunction cell efficiencies are predicted to be comparable to those of the conventional structures, and even small improvements in the GaInAsN cell may lead to higher multijunction cell efficiencies, especially for high-radiation applications and when cell operating temperature is low.

A system has been developed at Jefferson Lab for measuring transverse position of very low current beams delivered to the Experimental Hall B of the Continuous Electron Beam Accelerator Facility (CEBAF). At the heart of the system is a position sensitive cavity operating at 1497 MHz. The cavity utilizes a unique design which achieves a high sensitivity to beam position at a relatively low cavity Q. The cavity output RF signal is processed using a down-converter and a commercial lock-in amplifier operating at 100 kHz. The system interfaces with a VME based EPICS control system using the IEEE, 488 bus. The main features of the system are simple and robust design, and wide dynamic range capable of handling beam currents from 1 nA to 1000 nA with an expected resolution better than 100 {mu}m. This paper outlines the design of the system.

A two-stage beam transport for polarized protons has been constructed and operated at the Argonne ZGS. The first stage delivers vertically polarized protons (N-type) to an elastic scattering polarimeter consisting of a 10 cm long LH/sub 2/ target and two moveable sets of forward and recoil scintillation counters. The unscattered protons transported through the beam's second stage are focused onto the polarized proton target PPT-III; this target utilizes a 2.5 T R and A magnet to produce target polarizations in the horizontal plane, either in the beam direction (L-type) or transverse to it (S-type). The second stage of the beam is equipped with a combination of superconducting solenoids and dipole magnets; thus the beam polarization can also be rotated to point in the L or S direction. The entire system has been operated successfully over the momentum range 1.0 to 11.75 GeV/c with NS, LS, SS, and LL beam target spin directions.

None

The use of the electromagnetic method for geothermal reservoir exploration and delineation was studied. A number of techniques were developed to provide high quality field data. The remaining problem of interpreting these data in regions of complex geologic structure was overcome by the development of a numerical solution based on the hybrid technique, making use of both the finite element and the integral equation techniques. The major improvement is in the computing speed. (ACR)

This paper discusses the following on quantum gravity: 2 + 1 gravity as a Chern-Simons theory; quantization; dynamics; the Braid group; and the emergence of space and time. 16 refs., 3 figs. (LSP)