We show that bonded hydrogen in a-Si:H is readily exchanged by atomic deuterium when exposed to a deuterium plasma discharge. The effective diffusion coefficient for the D,H exchange 10/sup -14/ cm/sup 2//sec at 160/sup 0/C, is comparable to that of interstitial hydrogen in c-Si.

Repository-oriented leaching experiments involving Savannah River Laboratory (SRL) 165 type glass under a {gamma}-radiation field (1 = 0.2 x 10{sup 4} R/h) have been performed by the Nevada Nuclear Waste Storage Investigations (NNWSI) project. In this communication, we discuss glass surface analyses obtained by SEM, nuclear resonance profiling, and SIMS together with leachate solution data in relation to a mechanism that couples diffusion, hydrolysis (etching and gelation), and precipitation to qualitatively describe the release of different glass components to the leachant solutions. The release of mobile (e.g., Li) and partly mobile (e.g., B) species is controlled primarily by interdiffusion with water species across the interdiffusion zone. Glass components that are immobile in the interdiffusion zone are released to the solution by etching. For prediction of long-term steady-state concentrations of glass components with low solubility, the relative rates of release from the glass and secondary mineral precipitation must be taken into account.

The objective of this program is to develop a synthesis gas conversion catalyst with improved selectivity to gasoline or diesel range fuel via application of a micelle technique for preparing novel supported catalysts with specific size ruthenium particles. The major emphasis is to investigate hydrocarbon cutoff principle and to apply it for developing selective catalysts. We previously reported that cutoff is not effected with 40--60 {Angstrom} and 20--40 {Angstrom} ruthenium particles on {gamma}-Al{sub 2}O{sub 3}. We recently tested a catalyst with <20 {Angstrom} ruthenium particles. Well dispersed ruthenium in that catalyst extensively agglomerated to larger particles even during the course of a short test despite the high H{sub 2}:CO ratio used. Therefore, we could not conclude whether cutoff is effected with <20 {Angstrom} ruthenium particles. We are going to continue to evaluate the effect of operational conditions and also evaluate the effect of modifiers on ruthenium agglomeration. A catalyst with <20 {Angstrom} ruthenium particles will be evaluated to investigate occurrence of cutoff, after no agglomeration conditions are identified. We are now proposing to conduct, parallel to the main approach, a second research approach which will aim at developing a ruthenium catalyst with substantially lower light ends selectivity while maintaining at …

The objective of this program is to develop a synthesis gas conversion catalyst selective to gasoline or diesel range fuel via application of a micelle technique for preparing specific site supported ruthenium particles. The current emphasis is to investigate hydrocarbon cutoff principle and to apply it for developing selective catalysts. During this quarter, micelle technique was further improved and 1 ruthenium particle:l reverse micelle limit was approached by careful control of catalyst synthesis conditions. Accordingly, it became possible to synthesize supported particles that closely meet the size and composition targets originally set. This improved technique was applied to synthesis of chemically modified ruthenium catalysts. Some of the chemically modified ruthenium catalysts will be evaluated later in the program. We previously reported that 40--60 {Angstrom} ruthenium particles prepared on {gamma}-alumina do not result in hydrocarbon cutoff. We could not determine then whether smaller ruthenium particles result in hydrocarbon cutoff because these particles agglomerated via ruthenium carbonyl formation during the course of a 6--10 day test. We have recently evaluated a catalyst with 20--40 {Angstrom} ruthenium particles prepared on {gamma}-alumina by carefully analyzing products initially made during the test prior to substantial ruthenium agglomeration. We concluded that cutoff is not effected by …

The objective of this program is to develop a synthesis gas conversion catalyst with higher selectivity to liquid fuels, while maintaining catalytic activity and stability at least equivalent relative to state-of-the-art precipitated iron catalysts. During this quarter, the emphasis in the program has been the investigation of the hydrocarbon cutoff hypothesis with supported ruthenium catalysts. An alumina-supported catalyst with smaller than 20{Angstrom} ruthenium particles was tested under conditions of maximal water gas shift activity. During this test more than 90% of the water made in the Fischer-Tropsch synthesis reaction was converted to H{sub 2}. However, the extent of ruthenium metal agglomeration was not reduced. Accordingly, it was not possible to conclude whether hydrocarbon cutoff occurs with smaller than 20{Angstrom} ruthenium particles on {gamma}-alumina. A ruthenium catalyst prepared on Y-type zeolite had 20{Angstrom} or smaller ruthenium particles according to STEM examination and a 15{Angstrom} average ruthenium metal particle size according to EXAFS examination. The ruthenium metal particle size was stable during the test with this catalyst. The hydrocarbon product distribution was Anderson-Schulz-Flory with no cutoff up to a carbon number of 160. A well-dispersed titania-supported ruthenium catalyst is going to be evaluated during the next quarter in order to determine whether …

The objective of this program is to develop a synthesis gas conversion catalyst with higher selectivity to liquid fuels, while maintaining catalytic activity and stability at least equivalent relative to state-of-the-art precipitated iron catalysts. Hydrocarbon cutoff hypothesis and developmental needs for a ruthenium catalyst with low light ends selectivity were investigated during this quarter. Hydrocarbon product distribution was Anderson-Schulz-Flory up to a carbon number of 250 and cutoff did not occur with a titania-supported catalyst containing ruthenium particles smaller than 20{Angstrom}. It was found that an alumina-supported catalyst with 1% (by weight) ruthenium in the form of 50{Angstrom} to 100{Angstrom} metal particles was initially about half as active (by catalyst volume) and made one quarter of the amount of C{sub 1}{minus}C{sub 4} light end products relative to the Sasol precipitated iron catalyst.

Results of a TEM investigation of the microstructural changes produced by the room temperature implantation of energetic Kr/sup +/ ions into a glassy Ti-Cr thin film are reported. As in other metals, the Kr precipitates as solid crystallites. The precipitation of crystalline Kr is accompanied by ultrafine crystallization of the metal host around each Kr crystal. With increasing fluence, the Kr precipitates grow to a critical size at which they melt, and the adjacent fine metal crystals disappear. A new TEM imaging technique is described briefly which utilizes the small angle electron scattering fine structure and which in principle is capable of revealing all fine particles simultaneously.

One of the questions that must be answered in assessing the potential of pulsed microwave beams as directed energy weapons is, ''What is the maximum pulse energy (and/or peak power) that can be delivered from a source to a target.'' Atmospheric breakdown caused by the electromagnetic fields of the pulse sets one limit on energy propagation, and the breakdown threshold was the subject of fairly extensive investigation a number of years ago. The evolution of microwave source technology has extended the parameter range over which propagation needs to be understood, and additional issues that have not previously been investigated experimentally have assumed a new importance. A new generation of experiments is underway, planned, or proposed to investigate these issues. 13 refs.

In 4f compounds, there is a two-peaked structure associated with 4f photoemission spectroscopy, while most 5f compounds yield a single broad triangular-shaped 5f intensity. Evidence is presented from measurements on ternary alloys that show that at least part of the extra-5f intensity is due to the hitherto missing main peak (or d-screened f-hole peak) just as in the 4f systems. The remaining intensity is consistent with a band structure DOS. (The compounds used were URh/sub 3/B/sub x/, UPd/sub x/Rh/sub 3-x/, ThBe/sub 13/, UIr/sub 3/, and UBe/sub 13/.) (DLC)

The roles of energetic displacement cascades are ubiquitous in the fields of radiation damage and ion beam modifications of materials. These roles can be described on two time scales. For the first, which lasts approx. =10/sup -11/ s, small cascade volumes are characterized by large supersaturations of point defects and energy densities in excess of some tenths of eV's per atom. During this period, the system can be driven far from equilibrium with significant rearrangement of target atoms and the production of Frenkel pairs. Studies of ion beam mixing in conjunction with molecular dynamics computer simulations, have contributed largely toward understanding these dynamic cascade processes. At later times, the microstructure of the material evolves as cascades begin to overlap, or at elevated temperatures, point defects migrate away from their nascent cascades. It is shown how the primary state of damage in cascades influences this microstructural development. Examples involving radiation enhanced diffusion and ion-induced amorphization are discussed. 40 refs.

A rod consolidation demonstration with irradiated pressurized water reactor fuel was recently conducted by personnel from Nuclear Assurance Corporation and West Valley Nuclear Services Company at the West Valley Demonstration Project in West Valley, New York. The rod consolidation demonstration involved pulling all of the fuel rods from six fuel Assemblies. In general, the rod pulling proceeded smoothly. The highest compaction ratio attained was 1:8:1. Among the total of 1074 fuel rods were some known degraded rods (they had collapsed cladding, a result of in-reactor fuel densification), but no rods were broken or dropped during the demonstration. One aim was to gather information on the effect of rod consolidation operations on the integrity of the fuel rods during subsequent handling and storage. Another goal was to collect information on the condition and handling of intact, damaged, and failed fuel that has been in storage for an extended period. 9 refs., 8 figs., 1 tab.

The applicability, availability, and effectiveness of gas flow meters are assessed as a means for verifying the mass flows of pure UF/sub 6/ streams diluted with a carrier gas. The initial survey identified the orifice, pitot tube, thermal, vortex shedding, and vortex precession (swirl) meters as promising for the intended use. Subsequent assessments of these flow meters revealed that two - the orifice meter and the pitot tube meter - are the best choices for the proposed applications: the first is recommended for low velocity gas, small diameter piping; the latter, for high velocity gas, large diameter piping. Final selection of the gas flow meters should be based on test loop evaluations in which the proposed meters are subjected to gas flows, temperatures, and pressures representative of those expected in service. Known instruments are evaluated that may be applicable to the measurement of uranium or UF/sub 6/ concentration in a UF/sub 6/ - H/sub 2/ process stream at an aerodynamic enrichment plant. Of the six procedures evaluated, four have been used for process monitoring in a UF/sub 6/ environment: gas mass spectrometry, infrared-ultraviolet-visible spectrophotometry, gas chromatography, and acoustic gas analysis. The remaining two procedures, laser fluorimetry and atomic absorption spectroscopy, …

The sodium pumps for a liquid metal fast breeder reactor must be designed for exceptionally high reliability and long life. The principal adverse factor which tends to limit the primary pump life is cavitation which becomes potentially severe under off-design flow conditions caused by the requirement of two loop operations which resulted in a large operating flow range. This problem prompted an extensive study which included experimental investigations of scaled down and full size pumps. The investigations involved visual observations, acoustic signature recordings, and physical characteristic measurements of the model and full size impellers. The blade configuration of the model was modified several times. After each modification intensive testing was conducted with feedback to established design criteria. The results obtained from the final configuration showed excellent cavitation performance. This configuration was then machined on the full scale impeller and tested. The results confirmed acceptable performance in the entire range of operating conditions. This paper describes the test facilities erected for this study, discusses the experimental techniques employed, and presents the experimental techniques employed, and presents a sample of the experimental results.

Safety assessments and environmental impact statements for nuclear fuel cycle facilities require an estimate of potential airborne releases caused by accidents. Aerosols generated by accidents are being investigated by Pacific Northwest Laboratory to develop methods for estimating source terms from these accidents. Experiments were run by spilling viscous solutions and slurries to determine the mass and particle-size distribution of the material made airborne. In all cases, 1 L of solution was spilled from a height of 3 m. Aqueous solutions of sucrose (0 to 56%) gave a range of viscosities from 1.3 to 46 cp. The percent of spill mass made airborne from the spills of these solutions ranged from 0.001 to 0.0001. The mass of particles made airborne decreased as solution viscosity increased. Slurry loading ranged from 25 to 51% total solids. The maximum source airborne (0.0046 wt %) occurred with the slurry that had the lightest loading of soluble solids. The viscosity of the carrying solution also had an impact on the source term from spilling slurries. The effect of surface tension on the source term was examined in two experiments. Surface tension was halved in these spills by adding a surfactant. The maximum weight percent airborne from …

The infrared, optical and x-ray continua from radio quiet active galactic nuclei (AGN) are explained by a compact non-thermal source surrounding a thermal ultraviolet emitter, presumably the accretion disk around a supermassive black hole. The ultraviolet source is observed as the ''big blue bump.'' The flat (..cap alpha.. approx. = .7) hard x-ray spectrum results from the scattering of thermal ultraviolet photons by the flat, low energy end of an electron distribution ''broken'' by Compton losses; the infrared through soft x-ray continuum is the synchrotron radiation of the steep, high energy end of the electron distribution. Quantitative fits to specific AGN result in models which satisfy the variability constraints but require electron (re)acceleration throughout the source. 11 refs., 1 fig.

In this paper the wakefields for the Stanford Linear Accelerator Center (SLAC) accelerating structure are first discussed, and then some considerations dealing with the longitudinal wakefields are described. The main focus is on the effects of the transverse wakefield on the beam, including the case when there is an energy variation along the bunch. The use of an energy spread to inhibit emittance growth in a linac, indeed to damp the oscillations of the core of the bunch to below the unperturbed betatron oscillations, (in a process that is similar to Landau Damping) is qualitatively detailed. The example of the SLC, including errors, is also in detail.

The SERI Microalgae Culture Collection provides a repository for strains identified or developed for mass culture biomass production and makes these strains readily available to the research community. The strains in the collection have been selected for their potential in biomass fuel applications, and many produce significant quantities of cellular storage lipids. All of the newly added strains have been recently isolated by SERI and its subcontractors in organized screening programs. Many have been tested in outdoor mass culture systems, and several have demonstrated excellent performance as biomass producers. The strains added to the collection this year have been isolated from inland saline waters and marine waters. We believe that the strains in this collection can provide a source of extremely useful organisms, both for laboratory experimentation and for mass culture research. Most of the strains are currently nonaxenic. Again this year, cultures will be shipped free of charge to interested researchers. An important function of the culture collection catalog, in addition to listing the available strains, is to provide culture and performance data for each of the organisms. By collecting a summary of the requirements and characteristics of these organisms, we hope to allow requestors of cultures to begin …

Recent developments in high reliability components for linear induction accelerators (LIA) make possible the use of these devices as economical power drives for very high gradient linear colliders. A particularly attractive realization of this ''two-beam accelerator'' approach is to configure the LIA as a monolithic relativistic klystron operating at 10 to 12 GHz with induction cells providing periodic reacceleration of the high current beam. Based upon a recent engineering design of a state-of-the-art, 10- to 20-MeV LIA at Lawrence Livermore National Laboratory, this paper presents an algorithm for scaling the cost of the relativistic klystron to the parameter regime of interest for the next generation high energy physics machines. The algorithm allows optimization of the collider luminosity with respect to cost by varying the characteristics (pulse length, drive current, repetition rate, etc.) of the klystron. It also allows us to explore cost sensitivities as a guide to research strategies for developing advanced accelerator technologies.

A well characterized binary mixture of normal (protonated) and perdeuterated monodisperse 1,2 polybutenes has been studied by small-angle neutron scattering (SANS). For scattering wavevectors q greater than the inverse radius-of-gyration R/sub g//sup -1/, the SANS intensity is quantitatively predicted by the random phase approximation (RPA) theory of deGennes over all measured values of the segment-segment interaction parameter Chi. In the region (Chi s-Chi)Chi s/sup -1/ > 0.5 the interaction parameter determined using the RPA theory for q > R/sub g//sup -1/ is greater than that calculated from the zero-angle intensity based on an Ornstein-Zernike plot, where Chi s represents the limit of single phase stability. These findings indicate a correlation between the critical fluctuation length xi and R/sub g/ which is not accounted for by the RPA theory.

This project deals with the seasonal snow on Alaska`s Arctic Slope. It is concentrated on snow of the R{sub 4}D project area. However, an important aspect of this study is to relate the snow cover of this area with the rest of the Arctic Slope. The goals include determination of the amount of precipitation which comes as snow, the wind transport of this snow and its depositional pattern as influenced by drifting, the physical properties of the snow, the physical processes which operate in it, the proportions of it which go into evaporation, infiltration and runoff, and the biological role of the snow cover.

We present predictions for the rapidity and transverse momentum distributions for inclusive production of bottom quarks at SSC energies, pp ..-->.. bX. Our computations are based on the simplest, lowest-order QCD mechanisms. To estimate uncertainties, we use three different choices for structure functions, G(x,Q), as well as different choices for the evolution scale Q.

A goal of the LLNL Laser Pantography (LP) program has been demonstrating processes in which a computer-steered and computer-modulated laser beam directly deposits or removes material onto or from a substrate such as a silicon wafer. Substantial advantages could accrue from a fully developed set of such processes, including: lower cost for prototyping and low volume manufacturing, faster fabrication, on-line repair, and customized computers. 7 refs., 10 figs.

A calculational thermodynamic equilibrium analysis of the compatibility of ceramic-ceramic composites and a nonequilibrium assessment based on the literature of their use in proposed multimegawatt space nuclear power systems was performed. The five candidate composites included Al/sub 2/O/sub 3/-reinforced Al/sub 2/O/sub 3/, SiC-whisker-toughened Al/sub 2/O/sub 3/, SiC-whisker-toughened Si/sub 3/N/sub 4/, SiC-fiber-reinforced ZrC, and carbon-fiber-reinforced ZrC. The reactor concepts included Brayton cycle (continuous and burst mode) and Rankine cycle. It was determined that Al/sub 2/O/sub 3/-reinforced Al/sub 2/O/sub 3/ and carbon-fiber-reinforced ZrC are compatible in the Brayton-cycle continuous-mode system and that Al/sub 2/O/sub 3/-reinforced Al/sub 2/O/sub 3/, SiC-fiber-reinforced ZrC, and carbon-fiber-reinforced ZrC are compatible in the Rankine-cycle system. None of the candidate ceramic composite systems was likely to be sufficiently stable under Brayton-cycle burst-mode conditions.

The results obtained in a series of criticality experiments performed as part of a joint program on criticality data development between the United States Department of Energy and the Power Reactor and Nuclear Fuel Development Corporation of Japan are presented in this report along with a complete description of the experiments. The experiments involved lattices of Fast Test Reactor (FTR) fuel pins in an organic moderator mixture similar to that used in the solvent extraction stage of fuel reprocessing. The experiments are designed to provide data for direct comparison with previously performed experimental measurements with water moderated lattices of FTR fuel pins. The same lattice arrangements and FTR fuel pin types are used in these organic moderated experimental assemblies as were used in the water moderated experiments. The organic moderator is a mixture of 38 wt % tributylphosphate in a normal paraffin hydrocarbon mixture of C{sub 11}H{sub 24} to C{sub 15}H{sub 32} molecules. Critical sizes of 1054.8, 599.2, 301.8, 199.5 and 165.3 fuel pins were obtained respectively for organic moderated lattices having 0.761 cm, 0.968 cm, 1.242 cm, 1.537 cm and 1.935 cm square lattice pitches as compared to 1046.9, 571.9, 293.9, 199.7 and 165.1 fuel pins for the same …