As a result of testing, it was determined that control of the rate of quenching and the avoidance of accelerated aging by heating are the only means of modifying duralumin itself so as to minimize the intercrystalline form of corrosive attack. It is so simple a means that it should be adopted even though it may not completely prevent, but only reduce, this form of corrosive attack. By so doing, the need for protection of the surface is less urgent.

Although the corrosion resistance of sheet duralumin can be greatly improved by suitable heat treatment, protection of the surface is still necessary if long life under varied service conditions is to be insured. The coatings used for this purpose may be grouped into three classes: the varnish type of coating, the oxide type produced by a chemical treatment of the surface, and metallic coatings, of which aluminum appears to be the most promising. Since the necessary weather exposure tests are not complete, some of the conclusions regarding the value of various surface coatings are necessarily tentative.

The tests described in this report constitute a preliminary investigation of airfoil boundary layer control, as carried out in the atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory, from February to August, 1927. Tests were made on a U.S.A. 27 airfoil section with various slot shapes and combinations, and at various amounts of pressure or suction on the slots. The lift of airfoils can be increased by removing or by accelerating the boundary layer. Removing the boundary layer by suction is more economical than to accelerate it by jet action. Gauze-covered suction slots apparently give the best results. When not in operation, all suction slots tested had a detrimental effect upon the aerodynamic characteristics of the airfoil which was not apparent with the backward-opening pressure slots. Thick, blunt-nose airfoils would seem to give best results with boundary layer control.

An investigation on the cowling of radial air-cooled engines was conducted in the 20-foot Propeller Research Tunnel at Langley Field. Cooling and drag tests were made with each form of cowling. The propulsive efficiency was found to be practically the same with all forms of cowling.

The tests described in this paper afford a direct comparison of the efficiency and smoothness of flow obtained with propeller fan and multiblade centrifugal fan drives in the same wind tunnel. The propeller fan was found to be superior to the centrifugal fan in that the efficiency was about twice as great, and the flow much smoother.

Since aircraft design is tending toward all-metal construction, the strong heat-treatable light aluminum alloy, duralumin (a generic name for a class of heat-treatable alloys containing Cu, Mg, Mn, and Si), is finding increasing application. Doubt has been expressed concerning the reliability and permanence of these materials. Information is given on the effect of corrosion on the tensile properties of 14-gauge sheet duralumin, heat treated by quenching in hot water after being heated for 15 minutes in a fused nitrate bath at 500 to 510 C. Intercrystalline corrosion and practical aspects of intercrystalline embrittlement are discussed with respect to duralumin.

The permanence, with respect to corrosion, of light aluminum alloy sheets of the duralumin type, that is, heat-treatable alloys containing Cu, Mg, Mn, and Si is discussed. Alloys of this type are subject to surface corrosion and corrosion of the interior by intercrystalline paths. Results are given of accelerated corrosion tests, tensile tests, the effect on corrosion of various alloying elements and heat treatments, electrical resistance measurements, and X-ray examinations.

Tests were conducted to investigate the possibility of a serious accident arising from unintentional contact with the water in substantially horizontal flight at high speed. Referring to vector diagrams on Figure 2, it will be seen that a very dangerous condition may arise if the float be allowed to come in contact with the water at high speeds as, for example, when flying at high speed just above the water. The initial diving moment due to suction and drag combined may be great enough to cause the seaplane to nose under before the pilot is able to control the motion.

"Biplane cellules using the N.A.C.A.-M6 airfoil section have been tested in the variable density wind tunnel of the National Advisory Committee for Aeronautics. Three cellules, differing only in the amount of stagger, were tested at two air densities, corresponding to pressures of one atmosphere and of twenty atmospheres. The range of angle of attack was from -2 degrees to +48 degrees. The effect of stagger on the lift and drag, and on the shielding effect of the upper wing by the lower at high angles of attack was determined" (p. 1).

"A peculiar phenomena in seaplane landing is observed and reported. The seaplane having executed a normal fast landing at low incidence, a forward movement of the control stick effected an unusual condition in that the seaplane left the water suddenly in an abnormal attitude. The observations describing this phenomena are offered as a warning against possible accident and as a conjectural cause of seaplane landing accidents of a certain kind" (p. 1).

A brief description is given of different groups of high chromium steels (rustless iron and stainless steels) according to their composition and more generally accepted names. The welding procedure for a given group will be much the same regardless of the slight variations in chemical composition which may exist within a certain group. Information is given for the tensile properties (yield point and ultimate strength) of metal sheets and welds before and after annealing on coupons one and one-half inches wide.

This report records observations and recommendations resulting from an inspection trip to representative aircraft manufacturing establishments and repair stations. This inspection was made for the Navy Department and was specifically in reference to gluing practice at the various places visited. The period of the visits was between November 23, 1926 and February 16, 1927.

"The drag of a Sperry Messenger airplane with the wings removed, and also the drag of its various component parts, was measured in the 20-foot air stream of the N.A.C.A. propeller research tunnel at air speeds from 50 to 100 m.p.h. It was found that the three-cylinder radial air-cooled engine nearly doubled the drag of the bare fuselage, and the drag of the landing gear was about the same as that of the fuselage and engine combined" (p. 1).

A special protractor was designed and built with a view towards supplying a simple, inexpensive, practical, portable instrument for making measurements to detect propeller warpage under practically all conditions, without the use of auxiliary equipment, and without having to remove the propeller from the airplane. A detailed description is given of the protractor. Techniques for measuring are described. Directions are given on how to use the protractor to set detachable blade-type propellers on an airplane.

In order to experimentally study the conditions leading to ice formation on aircraft surfaces, an aircraft was equipped with small auxiliary surfaces and aerodynamic shapes similar to struts, wires, Pitot heads, etc. This airplane was flown at an altitude where a temperature of 32 F was encountered, at such times as cloud formations could be found at the coincident altitude. Here it was discovered that ice formed rapidly in regard to quantity, character, shape, and rapidity of formation.

Force tests on a systematic series of wing systems over a range of angle of attack from minus forty-five degrees to plus ninety degrees are covered in this report. The investigation was made on monoplane and biplane wing models to determine the effects of variations of tip shape, aspect ratio, flap setting, stagger, gap, decalage, sweepback, and airfoil profile.

"The assumption is made that a skeleton or cutaway center section is desirable for forward vision and to determine the effect of such mutilation upon performance the following work was done. The airplane used was a Vought VE-7 and in addition to the cutaway center section a system of end plates or fins was installed. Various conditions and combinations were investigated in level flight and in climb" (p. 1).

This note describes tests of the drag due to a Wright "Whirlwind" (J-5) radial air-cooled engine mounted on a cabin type airplane. The tests were made in the 20-foot Propeller Research Tunnel of the National Advisory Committee for Aeronautics. The drag was obtained with three different types of exhaust stacks: Short individual stacks, a circular cross section collector ring, and a streamline cross section collector ring.

"In order to study the effect of the fuselage, landing gear, and engine on the air flow through the propeller, a survey was made in the plane of the Sperry Messenger propeller with the propeller removed. The tests were made in the 20-foot air stream of the propeller research tunnel of the National Advisory Committee for Aeronautics at Langley Field, Virginia. The variation of the velocity with distance from the center in the propeller plane was found to be appreciable and well worth consideration in the design of propellers" (p. 1).

A series of experiments made in the wind tunnel of the Daniel Guggenheim School of Aeronautics, New York University, on the effect of tip shields on a horizontal tail surface are described and discussed. It was found that some aerodynamic gain can be obtained by the use of tip shields though it is considered doubtful whether their use would be practical.

"This note describes a simple and inexpensive method for determining the deflection of propeller blades under operating loads. Both the centrifugal force and air force loads are applied statically as a number of concentrated loads by means of weights and wires. Two methods of attaching the wires to the propeller blades have been tested, both giving approximately the same deflections. The method is considered useful for studying the deflections of propellers of different shapes under various operating conditions" (p. 1).

The purpose of this report is to correlate, bring up to date, and put under a single cover all the information thought to be essential to an understanding of the formulas regarding bearing strength of wood under steel aircraft bolts and washers and other factors influencing fitting design.

This report is concerned with the importance of the flat-top lift curve as a factor contributing to safety and control at low speed. An analysis of existing airfoil data indicated definite relations between the shape of the lift curve and certain section dimensions. The shape of the lift curve at maximum lift appears to be of sufficient importance to justify additional investigation with the view of developing a section with satisfactory efficiency and moment characteristics.

These tables are intended to provide a standard method and to facilitate the calculation of the quantity of "Standard Helium" in high pressure containers. The research data and the formulas used in the preparation of the tables were furnished by the Research Laboratory of Physical Chemistry, of the Massachusetts Institute of Technology.