From Summary: "An accurate determination of the end-gas condition was attempted by applying a refined method of analysis to experimental results. The results are compared with those obtained in Technical Report no. 655. The experimental technique employed afforded excellent control over the engine variables and unusual cyclic reproducibility. This, in conjunction with the new analysis, made possible the determination of the state of the end-gas at any instant to a fair degree of precision. Results showed that for any given maximum pressure the maximum permissible end-gas temperature increased as the fuel-air ratio was increased. The tendency to detonate was slightly reduced by an increase in residual gas content resulting from an increase in exhaust backpressure with inlet pressure constant."

Note presenting a description of a large number of corrugated diaphragms of beryllium copper, phosphor bronze, and Z-nickel with geometrically similar outlines but various diameters and thicknesses were formed by hydraulic pressing. The apparatus and technique used in the manufacture, testing, and heat treatment are described. Results regarding pressure-deflection curves, load limit, effect of center reinforcing, snap-action diaphragms, deflection traverse, thickness variations, and concentrated central loads are provided.

Errors arising from yawed flow were also determined up to 20 degrees angle of attack. In axial flow, the Prandtl pitot tube begins at w/a approx. = 0.8 to give an incorrect static pressure reading, while it records the tank pressure correctly, as anticipated, up to sonic velocity. Owing to the compressibility of the air, the Prandtl pitot tube manifests compression shocks when the air speed approaches velocity of sound. This affects the pressure reading of the instrument. Because of the increasing importance of high speed in aviation, this compressibility effect is investigated in detail.

The conditions which must be met at the slipstream boundary are developed, after which it is shown with the aid of the reflection method how these limiting conditions may be complied with in the case of an airfoil in a propeller slipstream in horizontal flow as well as for the propeller in yaw and with allowance for the slipstream rotation. In connection herewith, it is shown how the effective angles of attack and the circulation distribution with due regard to slipstream effect can be predicted and what inferences may be drawn therefrom for the distribution of lift, drag, and pitching moment.

"Engine and airplane performance data have been gathered from various sources and analyzed to determine indications of the most economical methods of flight operation from a consideration of fuel expenditure. The analysis includes the influence of such facts as fuel-air ratio, engine speed, engine knock, altitude, cylinder cooling, spark timing, and limits of cruising brake mean effective pressure. The results indicate that the cheapest power is obtained with approximately correct mixture at low engine speed and highest permissible manifold pressure" (p. 1).

The most conspicuous of the features of the enlarged N.A.C.A. tank are derived directly from those of the original tank and owe their present form not only to the reasons for their first use but also to the experience obtained with them. As in the original tank, there are: 1) A basin of great length (new 2,880 feet); 2) Rails made of structural H beams, without machining; 3) A towing carriage of very high speed (now 80 mph maximum); 4) Rubber tires on all the wheels, pneumatic on the running wheels and solid on the guide wheels.

"An investigation has been completed on several methods for the prevention and removal of ice on an airplane windshield. Tests were made on the use of electric heating, hot-air heating, and an alcohol-dispensing, rotating wiper blade. The results showed that vision through the airplane windshield could be maintained during severe icing conditions by the use of heat" (p. 1).

"The strength of representative types of flush-riveted joints has been determined by testing 865 single-shearing, double-shearing, and tensile specimens representing 7 types of rivet and 18 types of joint. The results, presented in graphic form, show the stress at failure, type of failure, and d/t ratio. In general, dimpled joints were appreciably stronger than countersunk or protruding-head joints, but their strength was greatly influenced by constructional details" (p. 467).

Monthly report documenting orders, opinions, and other legal statements issued by the Office of the Attorney General in Texas.

"A method has been developed for making photoelastic analyses of three-dimensional stress systems by utilizing the polarization phenomena associated with the scattering of light. By this method, the maximum shear and the directions of the three principal stresses at any point within a model can be determined, and the two principal stresses at a free-bounding surface can be separately evaluated. Polarized light is projected into the model through a slit so that it illuminates a plane section" (p. 1).

"Pressure-distribution tests of an N.A.C.A. 0009 airfoil with a 50-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made in the N.A.C.A. 4- by 6- foot vertical tunnel. The tests supplied aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab" (p. 1).

"Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and the yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degree pitch; 0 degree, 5 degree, and 10 degree yaw; and with split flaps covering 25, 50, 75, and 100 percent of the wing span and deflected 60 degrees. The results are given in the form of load distributions and as calculated moment coefficients" (p. 1).

"The pressure distribution on the fuselage of a midwing airplane model was measured in the NACA 8-foot high speed wind tunnel at speeds from 140 to 440 miles per hour for lift coefficients ranging from -0.2 to 1.0. The primary purpose of the tests was to provide data showing the air pressures on various parts of the fuselage for use in structural design. The data may also be used for the design of scoops and vents. The results show that the highest negative pressures occurred near the wing and were more dependent on the wing than on the fuselage" (p. 1).

The physical phenomena involved in the icing of aircraft have been analyzed and measured. Recommendations on warning devices are made as well as the different types of ice and glazing that can occur on airplanes are examined and discussed.

"Tidewater and weather-exposure tests on various aluminum alloys, magnesium alloys, and stainless steels are now being conducted by the National Bureau of Standards. Exposures were begun in June 1938 and, according to present plans, are to continue over a 3-year period. The methods of exposure and the materials being investigated are described and the more important results obtained up to the conclusion of the first year's exposure are reported" (p. 1).

"The relationship between stress and strain, and between stress and permanent set, for 18:8 alloy as affected by prior plastic deformation is discussed. Hysteresis and creep and their effects on the stress-strain and stress-set curves are also considered, as well as the influence of duration of the rest interval after cold work and the influence of plastic deformation on proof stresses, on the modulus of elasticity at zero stress, and on the curvature of the stress-strain line. A constant (c sub 1) is suggested to represent the variation of the modulus of elasticity with stress" (p. 539).

Data complied regarding wells and other water resources, including water quality analysis, measurements, and other relevant information.

Data complied regarding wells and other water resources, including water quality analysis, measurements, and other relevant information.

"An investigation of the interference associated with tail surfaces added to wing-fuselage combinations was included in the interference program in progress in the NACA variable-density tunnel. The results indicate that, in aerodynamically clean combinations, the increment of the high-speed drag can be estimated from section characteristics within useful limits of accuracy. The interference appears mainly as effects on the downwash angle and as losses in the tail effectiveness and varies with the geometry of the combination" (p. 689).

This report discusses the efforts being made to remove the source of danger to passengers arising from the fracturing of silicate glass and some of the alternatives presented include: single-layer safety glass, multi-layer safety glass, transparent plastic resins.

"Rate-of-discharge curves that show the discharge characteristics of an injection system having a very short fuel passage are presented. The rate of discharge closely follows the rate of displacement of the injection-pump plunger for open nozzles in which the maximum calculated pressures at the orifice do not exceed a certain value, which is dependent on the particular injection pump. With small orifices and high pump speeds, the rate of discharge does not follow the rate of plunger displacement because the higher discharge pressure results in increased leakage with corresponding decrease in discharge rate" (p. 1).

This report describes experiments made for the purpose of ascertaining the effective width of circularly curved sheet under pure flexural stress. A relation for the effective width of curved sheets is established. Experiments were made with circular cylinders compressed in longitudinal direction. The sheets were rigidly built in at the sides parallel to the axis of the cylinder.

This report contains a description of new methods of fabrication, new equipment, and special tools, with a view to supplying data for design from economical points of view, as well as to stimulate the interest of other factories in improved shop methods. Some of the topics include the method and tools for changing the sectional shape of light-alloy and steel tubes, skin riveting, automatic strip insertion for drawing-sheet sections, silent beating tools, beam strap milling machines, drilling and countersinking tools for mounting standard parts, and tools for creasing thin sheets.

"A study was made of the factors affecting the pressure available for ground cooling in front of a cowling. Most of the results presented were obtained with a set-up that was about one-third full scale. A number of isolated tests on four full-scale airplanes were made to determine the general applicability of the model results. The full-scale tests indicated that the model results may be applied qualitatively to full-scale design and quantitatively as a first approximation of the front pressure available for ground cooling" (p. 1).