The majority of two-phase flow problems involving equations of state are solved by use of point-wise utilization steam table values. In this manner, problems involving the use of the various flow equations of continuity, momentum and energy are generally forced into iterative solutions. Considerable effort towards the development of an analytical expression for the state equation seems indicated so as to simplify the analysis of two-phase problems, particularly apparent in the analysis of systems undergoing phase transformation as demonstrated by the significant difference between simple theory and experimental critical flow determinations. The assumption of homogeneous, equilibrium mixture is indicated as a first attack upon the problem.

Results are summarized on theoretical considerations of the excited states of the Ca isotopes, experimental studies of the level structure of Ca42 and Ca44, studies of the production of circularly polarized bremsstrahlung by beta rays, the Moller scattering spectrometer, and the Moller scattering coincidence experiment.

The purpose of the test was to check the extraction crane rails in the area of the reactor pit for level and parallelism. The west extraction crane rail exceeded the allowed tolerance of 1/32 inch at only one location. The elevation of the north bumper was out of tolerance by 1/64 inch. The east extraction crane rail was consistently lower than the west rail by as much as 8/64 inch. The east rail was parallel with the west rail within allowable tolerances over the length tested except at one location where the transit was located, approximately 41 feet from the north bumper.

The purpose of the test was to determine the radiation levels inside the concrete enclosures but outside the reactor plant containers after shutdown following plant power operation. Radiation levels at the survey points in the 1-AC and 10BD Boiler Chambers Enclosures and in the Reactor Container Enclosure indicated that no significant radiation hazards were present approximately 25 minutes after all rods had been inserted. The radiation levels approximately 4 minutes after shutdown at the survey points in the Auxiliary Chamber Enclosure indicated that several points were above background, the highest test level being obtained in contact with the East Auxiliary Chamber container drain pipe.

Abstract: Critical experiment studies were performed, varying the parameters U235, B10 and metal to water ratio, in the SM-2 7 x 7 core configuration with 38 stationary elements and seven control rods of the SM-1 (APPR-1) type. An experimental mock-up of the SM-1 was assembled using the basic SM-2 fuel plates. Excellent agreement between the SM-1 boron loading, determined by chemical analysis, and the SM-1 mock-up boron loading, for equivalent bank positions, was noted. Several SM-2 mock-ups, cold clean and midlife, were assembled and studied with regard to reflector effects, flow divider effects, relative control rod array worths, critical rod configurations, and relative power distributions. The results of these experiments indicate as satisfactory a U235 loading of 36.4 Kg and a B10 loading of 63.4 grams for the SM-2. Attention is drawn to numerous power peaks present in the active core. The open seven control rod array has a slight reactivity advantage over the closed seven array and consequent minor disadvantage with respect to "stuck rod" criteria.

The original goal of this investigation was to compare the thermodynamic characteristics of the gases in and behind the shock fronts in gases at initial pressures in the millimeter range and to compare these characteristics in the geometries of single and double discharges. The shock fronts were not visible, so it was not possible, at these pressures, to get visual data from the shock front itself. The parameters giving the properties of the gases were faces. Measurements made with an image converter camera (which is still in the development stage) agree well with these made with a photomultiplier tube. Differences are observed between the front velocities in the cases studied. These are of the order of 3 to 15 per cent. Considering the nature of the shot to shot fluctuations in the discharges and the inductance variation between the single and double discharges represent a physical difference. The mathematical treatment which says that two equal strength colliding with a wall behaves, has not been shown to be inadequate by this investigation. It was hoped that a stronger confirmation could be fien to the theory, but the accuracy of the data does not warrant it.

The first series of tests in the KER-REP-1 loop proved that a fission product contaminated loop could be decontaminated to a safe level for contact maintenance. Since a good decontamination process was available, there was much that could be improved about this process. Further testing of this process and several variations of other processes have been scheduled. The evaluation of these processes includes specific decontamination factors, process corrosion, and loop activity reduction factors (loop decontamination factors).

The purpose of the test was to determine if failed blanket elements exist in other regions of the core beside F-2. FEDAL sampling ports that have indicted the greatest deviation as determined in a statistical analysis performed on a number of traverses in the FEDAL system will be tested. Data obtained from the start up runs of the FEDAL sample port Nos. 11, 31, 36 and 37 of Monitor 2 and port Nos. 14, 46, 11, 49 and 7 of Monitor 1 gave no indications of a blanket element failure. At each power increase, the radiation increase was normal with no signs of bursts or peaks of radiation which would indication the failure of a blanket fuel element.

This review lists some of the salient features of semiconductor particle counters and cannot claim to contain an exhaustive listing of all the work in the field. Performance results on the surface-barrier counters as developed at California Institute of Technology are included as typical for this type of counter, though comparable results have been obtained elsewhere.

The PWR Plant was operated at approximately 60 MW net electrical output for a total of 1000 EFPH from February 3, 1959 to March 28, 1959. During this period, while performing DL-S-225, there were two planned shutdowns, no safety shutdowns or safety insertions and one flux title. The performance of the plant was satisfactory during the period of the test.

The utilization of gloves wherein heavy element additives have been included is a significant means of reducing exposure to hands and, consequently, increasing allowable working time in operations which require direct contact with low energy isotopes - such as plutonium. The number of such gloves available has been limited considerably by the feasibility of fabrication and the practicality of application. The following study was made on two basic gloves - the first, a heavy zinc-neoprene coated glove and the second, a lead loaded neoprene glove available in two thicknesses. Included in the study was a standard 30 gauge neoprene glove.

The purpose of the test was to determine the internal temperature of the valve position detector for the 1A reactor inlet hydraulic valve with the plant at normal pressure and temperature and at power. The normal operating temperatures for the valve position detector on the 1A reactor inlet hydraulic valve range from a minimum of 287 F to a maximum of 294.7 F.

The diffusion coefficient was calculated for the diffusion of Xe through Nb and found to be 0.064 exp (-18,600/RT).

In this technical report, firstly, the transfer function of a non-regenerative, base-driven transistor circuit is derived by applying the linear equivalent circuit method. The results are experimentally verified. Secondly, the idea of the inverse-gain-bandwidth is introduced as the criterion of the dynamic design. Thirdly, the stability factor is explained. Finally, it is shown that a system constructed by various types of transistor switching circuits is reduced to a long train of unit chains formed by delay units and wave-shapers, and the maximum allowable number of delay units in a unit chain is discussed. The results given here are consistent with the design procedures for transistor switching circuits established in the Digital Computer Laboratory, i.e., the emitter-follower logical circuits associated with restorers and flip flops.

The purpose of the test was to determine the ability of the Control Air System to provide the necessary quantity and quality of clean, dry air to keep the rod drive mechanism stator and position indicator housings at about 3 PSIG in order to avoid low stator resistances resulting from condensation during plant cooldown. The Control Air System is capable of providing the quality of air specified in AEC letter SBO:JWF:100 dated November 17, 1958 of less than 44 grains of moisture per lb. of air in the control air line nearest the reactor chamber.

The purpose of the test was to determine the operating conditions of the rod drive mechanisms so that operating personnel may be informed concerning malfunctioning mechanisms. The results the this test favorably agree with previous results. The operating characteristics of the rod drive mechanisms checked in this test have not changed appreciably.

The basic scheme for processing power reactor fuels at Hanford includes the removal of inert endfittings ("hardware") from the active sections of the fuels. Within Hanford Laboratories, research and development studies have been in progress on various types of saws which might be used for hardware cutoff. In the initial phase of the program, high-speed saws were investigated; more recently, studies on low speed saws have been conducted. This report summarizes the high speed saw studies and includes information on abrasive wheels, diamond wheels and metal "friction" blades which cut by actually melting metal ahead of the saw blade. At the completion of the low speed saw testing program currently in progress, basic saw types will be compared and the saw type to be included in the reprocessing complex will be selected.

The purpose of the test was to determine the temperature and pressure coefficients of reactivity at zero power. Data was obtained during this test which indicates a new temperature coefficient and a pressure coefficient corrected to station operating conditions of 500 F and 1785 PSIG.

The purpose of the test was to determine the level of the radiation field in the Turbine Plant during a significant power run. The initial power level survey had an average radiation level of 0.02 mr/hr. this survey showed and average radiation level of 0.03, which was considered background level. this radiation level was far below the maximum allowable level of 2 mr/hyr. No Neutrons were detected.

On July 31, 1959, an autoclave ruptured while being used for thermal cycling studies of Plutonium Recycle Test Reactor (PRTR) plutonium-aluminum fuel elements. Since stand-in materials were being used in this test, no contamination was involved. This accident could lead to inference of greater hazards associated with PRTR fuel designs than had previously been postulated. An ad hoc technical investigation committee was appointed by the Manager Reactor and Fuels Research and Development, to study the autoclave failure. The committee was charged with developing a sound technical explanation of the accident and/or recommending experimental programs to test hypotheses of the physical and chemical processes leading to the rupture of the autoclave.

Zircaloy-2 has a strong tendency to absorb oxygen and nitrogen at elevated temperatures. These gas impurities are extremely harmful, causing brittleness and loss of corrosion resistance. The production of ductile corrosion-resistant welds by present methods required shielding of the weld metal by an inert gas atmosphere or by a vacuum. The alternative to an inert gas atmosphere or a vacuum is reduction of the welding time to a few milliseconds of time to prevent gas absorption.

A study of the basic problems associated with the use of electrical propulsion systems for space travel has been carried out at the Lawrence Radiation Laboratory. The emphasis is on large systems capable of manned flight.

Introduction. As has been shown by Post, the total power required to produce a strong, steady-state magnetic field is strongly dependent upon the temperature at which the electrical conductor of the magnet operates. The power required for operation at very low temperature can, in some cases, be much less than that required for ambient temperature operation. The power required for low temperature operation depends on many system characteristics which include the metal chosen for the electrical conductor, the purity of this metal, and efficiency of the refrigeration equipment. This paper shows the relative power requirement, as a function of temperature, of a magnet with a particular shape and with a field strength of 100,000 gauss. Data is shown for three electrical conductors: copper, aluminum, and sodium.

Abstract: "Tungsten-rich alloys, developed for use at temperatures up to 2000F, exhibit ductility, fabricability and joinability not found in commercially-available materials. An envelope type of microstructure was produced in compositions containing at least 90 wt% tungsten by liquid-phase sintering of cold-pressed powders in hydrogen. At room temperature the alloys could be rolled extensively, and tensile elongations up to 25% were noted. Strength properties of a W-Ni-Fe base were improved by small quaternary additions. The ultimate tensile strength of a 90W-4.8Ni-3.2Fe-2Ru alloy was 46,700 psi at 2000F, compared to 30,000 - 35,000 psi for unalloyed tungsten or W-Ni-Fe; the 100-hour stress-rupture strength at 1600F was 15,000 psi. Excellent joints were produced by spot welding and localized induction heating. The oxidation resistance of unprotected 90 wt% tungsten compositions was not significantly affected by alloying."