Abstract: An alluminum-clad low-enrichment, uranium-alloy fuel element of flat plate configuration has been proposed for the Organic Moderated Reactor (OMR).

Introduction: A low-capacity, low-decontamination plant can be built, as part of a power reactor complex, to avoid long distance transfer of fuel to a high-capacity aqueous processing plant. Activation of such a complex, with the processing plant adjacent to the reactor it serves, could decrease the cost of the integrated fuel cycle. The study of this concept is a major objective of the Processing Refabrication Experiment (PRE).

From introduction: The Commission's underlying objective of this program is to conduct sufficient engineering and development work to determine the most feasible and economical methods of producing nuclear super-heated steam from a boiling water reactor.

Abstract: During the course of power run 14 on the Sodium Reactor Experiment (SRE) at low power, the temperature difference among various fuel channels was found to be undesirably high. Normal operating practices did not succeed in reducing this temperature difference to acceptable values and on July 26, 1959, the run was terminated.

This report summarizes the hazards associated with the operation of the Lynchburg Test Reactor (LTR) critical experiments. The LTR critical experiment program is outlined and the design of the experiment is described. The experiments will provide basic data to check two-dimensional calculational methods and provide information needed in the design of the LTR.

Technical report. From Abstract: "An ion exchange process was demonstrated for the recovery of Pu238 from irradiated neptunium oxide. Three cycles of anion exchange proved adequate for the removal of fission products and for the separation of the neptunium and plutonium from each other."

Technical report. From Abstract: "Ultrasonic energy appropriately applied to the die or container of a laboratory-type direct extrusion press effected a marked increase in the free extrusion rate of lead and aluminum billets at a constant extrusion rate. the same results were obtained in extrusion cladding steel tubes with aluminum. Rate increases were generally 100 per cent or greater, and decreases in force were usually within the range of 10 to 20 per cent. Furthermore, the shape and slope of the extrusion curves were altered. The effect appeared to be attributable to a reduction of both die friction and container wall friction under ultrasonic influence."

Technical report. From Abstract: "Rate data are presented for the oxidation of neptunium (V) by vanadium (V) in nitric acid." From Summary: "Rates of oxidation of neptunium (V) were determined by a solvent extraction technique based on the difference in distribution coefficients for neptunium (V) and neptunium (VI)."

Abstract: Critical experiment studies were performed, varying the parameters U235, B10 and metal to water ratio, in the SM-2 7 x 7 core configuration with 38 stationary elements and seven control rods of the SM-1 (APPR-1) type. An experimental mock-up of the SM-1 was assembled using the basic SM-2 fuel plates. Excellent agreement between the SM-1 boron loading, determined by chemical analysis, and the SM-1 mock-up boron loading, for equivalent bank positions, was noted. Several SM-2 mock-ups, cold clean and midlife, were assembled and studied with regard to reflector effects, flow divider effects, relative control rod array worths, critical rod configurations, and relative power distributions. The results of these experiments indicate as satisfactory a U235 loading of 36.4 Kg and a B10 loading of 63.4 grams for the SM-2. Attention is drawn to numerous power peaks present in the active core. The open seven control rod array has a slight reactivity advantage over the closed seven array and consequent minor disadvantage with respect to "stuck rod" criteria.

Development of more reliable, lower cost components for high temperature liquid metal-cooled reactor plants.

Report documenting ongoing research and development carried out by the Instrumentation and Controls Division of the Oak Ridge National Laboratory.

Report containing information regarding the design of the Tory II-A nuclear ramjet engine, and descriptions of its locale, test program, and possible hazards.

The PWR Plant was operated at approximately 60 MW net electrical output for a total of 1000 EFPH from February 3, 1959 to March 28, 1959. During this period, while performing DL-S-225, there were two planned shutdowns, no safety shutdowns or safety insertions and one flux title. The performance of the plant was satisfactory during the period of the test.

The purpose of the survey was to determine the radiation levels in the 1 D Boiler Chamber during plant operation. The conclusion of this survey is that the radiation level in the 1 D Boiler Compartment with the 1A, 1B, and 1C Main Coolant loops in service at approximately 100 per cent power ranged from .03 MR/HR to 6.0 MR/HR.

The purpose of the survey was to determine the radiation level in the Turbine Generator Services Building, around the Fuel Handling Canal, in the limited access areas of the reactor plant containers and on the boiler container roofs during plant operation. The test was performed with the plant at approximately 100 per cent power with three loops (1A, 1B, and 1C) in service. The radiation levels of the areas surveyed with a few exceptions were essentially background (.03 MR/HR). These exceptions were the Auxiliary Chamber and the limited access areas between the containers. The highest radiation level obtained in the survey was >2500 MR/HR at the reactor chamber walkway.

The purpose of the test was to determine the direction and magnitude of any drift in the temperature sensing elements and the receiver-indicating units for the primary loop and pressurizer resistance thermometers. To obtain intercalibration data for various temperature sensing elements in the primary coolant system. To obtain data on the difference between the calculated signal generated by the BF-3 counters, considering the known rate of decay of the PO-BE source, and the measured values. Determination of temperature sensing element and instrumentation drifts could not be made due to a lack of comparative data. Five temperature intercalibrations were performed using the calibrating Tc resistance thermometers as a standard. The data obtained from the nuclear instrumentation was too erratic to form any conclusions.

The purpose of the test was to determine the direction and magnitude of any drift in the temperature sensing elements and the receiver-indicating units for the primary loop and pressurizer resistance thermometers. To obtain intercalibration data for various temperature sensing elements in the primary coolant system. To obtain data on the difference between the calculated signal generated by the BF-3 counters, considering the known rate of decay of the PO-BE source, and the measured values. Of the 62 core thermocouples observed 19 were either reading less than 400 F or were reading in excess of 20 F from the calibrating thermometer temperatures. In each case the thermocouple was considered defective. The remainder were within 2 per cent of the calibrating thermometers. The primary loop (Norwood Indicators) resistance thermometers all read with 0.2 percent of the calibrating thermometers. No conclusion could be made for the pressurizer temperature instruments or the boiler Tb resistance thermometers, except that the 1A boiler temperature varied 10 F to 20 F from the 1Band 1C boiler temperatures. A laboratory calibration of this instrument will be made. The data obtained from the source range nuclear instrumentation was too erratic to form any conclusion. No drift evaluation on …

The purpose of the test was to determine the responses of the plant when subjected to load transients exceeding the design magnitudes, and to determine the maximum load changes, positive or negative, that the plant can sustain. The reactor plant responded satisfactorily to all load transients. The only limits exceed were the pressurizer high and low level alarm points. The magnitude of the transients and the time required for the plant to return to equilibrium was dependent upon the size of the the load change. The pressurizer spray was effective in reducing reactor coolant pressure positive surges; however, this resulted in larger negative surges than when the spray valve was closed.

The purpose of the test was to determine the temperature and pressure coefficients of reactivity at zero power. Data was obtained during this test which indicates a new temperature coefficient and a pressure coefficient corrected to station operating conditions of 500 F and 1785 PSIG.

The purpose of the test was to determine the level of the radiation field in the Turbine Plant during a significant power run. The initial power level survey had an average radiation level of 0.02 mr/hr. this survey showed and average radiation level of 0.03, which was considered background level. this radiation level was far below the maximum allowable level of 2 mr/hyr. No Neutrons were detected.

The purpose of the test was to determine the ability of the Control Air System to provide the necessary quantity and quality of clean, dry air to keep the rod drive mechanism stator and position indicator housings at about 3 PSIG in order to avoid low stator resistances resulting from condensation during plant cooldown. The Control Air System is capable of providing the quality of air specified in AEC letter SBO:JWF:100 dated November 17, 1958 of less than 44 grains of moisture per lb. of air in the control air line nearest the reactor chamber.

In this technical report, firstly, the transfer function of a non-regenerative, base-driven transistor circuit is derived by applying the linear equivalent circuit method. The results are experimentally verified. Secondly, the idea of the inverse-gain-bandwidth is introduced as the criterion of the dynamic design. Thirdly, the stability factor is explained. Finally, it is shown that a system constructed by various types of transistor switching circuits is reduced to a long train of unit chains formed by delay units and wave-shapers, and the maximum allowable number of delay units in a unit chain is discussed. The results given here are consistent with the design procedures for transistor switching circuits established in the Digital Computer Laboratory, i.e., the emitter-follower logical circuits associated with restorers and flip flops.

In this paper we are concerned with the potentials and electrical currents flowing at an interface between two phases as a result of chemical reactions which promote selective ion migration. Although our immediate concern is an explanation of the available results on smelting, a sufficiently broad understand requires that we go far beyond this limited results and bring together the findings from many related fields. We first must consider the diffusion of particles across an interface, which for convenience we will speak of as a membrane since convection currents usually stir both phases except for a thin boundary layer.

The purpose of the test was to determine the internal temperature of the valve position detector for the 1A reactor inlet hydraulic valve with the plant at normal pressure and temperature and at power. The normal operating temperatures for the valve position detector on the 1A reactor inlet hydraulic valve range from a minimum of 287 F to a maximum of 294.7 F.