An investigation was conducted on a 35 deg swept-wing fighter airplane to determine the effects of several blunt-trailing-edge modifications to the wing and tail on the high-speed stability and control characteristics and tracking performance. The results indicated significant improvement in the pitch-up characteristics for the blunt-aileron configuration at Mach numbers around 0.90. As a result of increased effectiveness of the blunt-trailing-edge aileron, the roll-off, customarily experienced with the unmodified airplane in wings-level flight between Mach numbers of about 0.9 and 1.0 was eliminated, The results also indicated that the increased effectiveness of the blunt aileron more than offset the large associated aileron hinge moment, resulting in significant improvement in the rolling performance at Mach numbers between 0.85 and 1.0. It appeared from these results that the tracking performance with the blunt-aileron configuration in the pitch-up and buffeting flight region at high Mach numbers was considerably improved over that of the unmodified airplane; however, the tracking errors of 8 to 15 mils were definitely unsatisfactory. A drag increment of about O.OOl5 due to the blunt ailerons was noted at Mach numbers to about 0.85. The drag increment was 0 at Mach numbers above 0.90.

Report presenting an investigation at Mach numbers of 1.61 and 2.01 to determine the pressure distributions for a series of 20 controls on a 60 degree delta wing. Tests occurred at a range of angles of attack and control deflections. Results regarding basic pressure distributions, comparison of experimental and theoretical results, and experimental comparisons are provided.

Report presenting formulas for propellers for the rate of change of side-force coefficient with angle of yaw and for the rate of change of pitching-moment coefficient with angle of yaw. Charts of side-force derivatives are given for two propellers of different plan forms.

Report presenting an investigation to determine the effect of the amount of oil flow to the piston on the ring-sticking characteristics of a piston and ring assembly and on the engine oil consumption. Results regarding the blow-by, lubrication, oil consumption, and method of supplying oil are provided.

Report discussing the characteristics of the jet-motor air-intake duct system for a pursuit-type airplane with modifications to the duct system. Details of its effects on the Mach number, high pressure recovery, drag, and simplicity of the system are provided. Problems regarding the flow condition through the ducts and some potential modifications to prevent further issues are also described.

Report presenting testing of a representative bomber nacelle on a low-drag wing in the NACA two-dimensional tunnel. The adverse or interference effects of the nacelle on the low-drag wing were small.

Report presenting an investigation of the use of aerodynamic and mechanical devices for improving the response of guided missiles. An analysis indicates that the use of free-floating flaps and spring-mounted control surfaces should be able to increase maneuverability to the point that electronic automatic stabilization and gain-adjusting devices can be eliminated.

Report presenting testing in the high-speed wind tunnel to determine the drag characteristics of several types of radial-engine nacelle on a low-drag airfoil. The drag coefficients of nacelles incorporating cowling-nose shapes shown by previous tests to be efficient and afterbodies of adequate length were about the same magnitude as commonly obtained for comparable installations on conventional wings. Results regarding the reduction of data, effect of nacelles on lift, and pressures at wing-nacelle juncture are provided.

From Summary: "A method is outlined for determining in flight the weight rate of air flow to the engine equipped with a Bendix-Stromberg injection-type carburetor. The method has the advantage that no additional equipment need be inserted in the charge-air system and only a few simple measurements are necessary. The analysis of an air-box calibration of the carburetor to be used in interpreting the flight measurements is shown by an example."

Report presenting tests of a three-barrel pressure carburetor to determine the effect of nonuniformity of the air flow in the intake duct on the metering of the carburetor. Measurements were made in the air side of the metering system and in the carburetor barrels for a variety of flow distributions. Results regarding the metering pressure, altitude compensation, effect of throttle on the metering characteristics, and flow of air around the bends are provided

Report discussing a mock-up injection impeller created to investigate the hydraulic characteristics and limitations of the NACA injection impeller currently in use. Information about the form and magnitude of critical factors of fuel-transfer leakage and peripheral fuel distribution is provided as well as the effects of design variations of components on hydraulic characteristics. Several revisions in portions of the impeller are suggested to improve its fuel-transfer, fuel-pumping, and fuel-equalizing characteristics.

Report presenting an investigation conducted with trimethyl borate azeotrope and pentaborane fuels in a turbojet combustor. The primary purposes of the study were to determine the effect of boron oxide deposits on the turbine-nozzle area, combustor pressure loss, temperature distribution, and combustion efficiency. Three distinct boron deposit patterns were noted in the investigation.

"A method is developed for calculating the performance of a dual-rotating propeller from the section characteristics of the blade elements. The method is applied to an eight-blade dual-rotating propeller and the computed results are compared with low-speed wind-tunnel tests of the same propeller in both the tractor and pusher positions. The computations are found to agree within the experimental accuracy of the measurements" (p. 1).

Report presenting an investigation of the blades of an experimental two-blade jet-driven helicopter when subject to a condition of near resonance between the frequencies of the first elastic bending mode of the blades and third harmonic component of the aerodynamic loading that results in high bending strains in normal flight conditions. Various changes in design configuration on the blade bending strains were explored. Results regarding the preliminary studies, effects of variation in flight conditions and blade configuration, and harmonic analysis are provided.

Report presenting a partly linearized solution of plastic deformation of a rotating disk based on the deformation theory of plasticity and considering finite strains. The method can be used to investigate the general plastic behavior of a rotating disk.

"A theoretical discussion of the application of blade boundary-layer control to increase the efficiency and the stage pressure ratio and to improve off-design performance of turbomachines is presented. A method based on the potential flow of a compressible fluid is developed for designing suction, or ejection, slotted blades having a prescribed velocity distribution along the blade and in the slot. The effect of the boundary layer on the design of the slot and the effect of ejecting gas at stagnation pressures and temperatures different from free-stream values are discussed" (p. 1).

From Summary: "Values of the downwash of a horseshoe vortex in compressible flow are presented in the form of charts and tables. The use of the charts and tables in the calculations of the downwash of wings of arbitrary plan form is discussed. The results of a few calculations are compared with experimental results."

Report presenting an investigation to determine the floating characteristics of full-length plain and horn-balanced rudders during rotary tests at spinning attitudes on a scale model of a typical low-wing personal-owner airplane. The investigation included the determination of the effects of the horizontal tail and the wing on the rudder floating characteristics.

Report presenting data for turbulent-velocity-fluctuation components and mean-velocity distributions measured in the subsonic jet issuing from a pipe in which a fully developed turbulent flow was established. Axial and radial components of the fluctuation velocities were examined as functions of Reynolds number and position in the jet.

"The present report covers a series of torsional tests on stiffened D-tubes of alclad 24S-T3 aluminum alloy having a cross section similar to the NACA 0012 airfoil section and a closing web at 30 percent of the chord. The stiffeners consisted of ribs and stringers. An average-strength chart has been developed for this type of structure that takes into account the skin thickness, rib spacing, and stringer spacing. This chart may also be used for unstiffened D-tubes" (p. 1).

Note presenting an account of explicit solutions in terms of Mathieu functions of the problem of two-dimensional subsonic compressible flow past oscillating airfoils. The results are applied to the calculation of three-dimensional corrections for the two-dimensional theory and the effect of the incorporation of the three-dimensional effects on the Mathieu function solution of the two-dimensional problem is shown.

Note presenting an analysis of the problem of two-dimensional flow behind a curved stationary shock wave. The method assumes a given shock-wave shape, which automatically determines certain initial conditions on flow variables, and flow-pattern, including any body shape, follows from initial conditions.

Report presenting an investigation in the high-speed 7- by 10-foot tunnel to determine some effects of tail height and wing plan form on the static longitudinal stability characteristics of a complete, small-scale model at high subsonic speeds. It had both a low-tail and high-tail position. Results regarding the lift and drag characteristics and longitudinal stability characteristics are provided.

Report presenting a description of a new blade series designed to operate at near choking inlet Mach numbers and to have near maximum critical Mach numbers by employing high aerodynamic loading of the profiles in the leading-edge region. Results regarding aerodynamic characteristics and prediction of high-speed performance are provided.