"Some aileron load characteristics for three thin wings varying in sweep have been presented for Mach numbers from 0.80 to 1.05. For the transonic Mach number range, shock effects exert a large influence on the loading, but the exact location of each shock for a specific wing design cannot be cataloged at the present time. It is shown, however, that the aileron loading, although greater in magnitude than at subsonic speeds, nevertheless varies in as uniform a fashion as at subsonic speeds" (p. 1).

Report presenting an investigation to determine the possibility of using simplified procedures for the estimation of control loads at supersonic speeds. The results indicated that relatively simple procedures are possible for the estimation of loadings on flap-type controls at supersonic speeds for cases when no flow separation occurs ahead of the hinge line.

Report presenting a wind-tunnel investigation at subsonic Mach numbers up to 0.9 to measure the root-mean-square variation of the normal forces on 27 NACA airfoil sections. The effects of thickness-chord ratio, camber, location of minimum pressure, and leading-edge radius were investigated.

From Introduction: "The intermediate subsonic speed range is considered and the liquid-metal turbine-propeller cycle discussed in this report. In this report, compressor pressure ratio, heat-exchanger air-inlet Mach number, and turbine-inlet temperature were optimized for maximum engine net thrust per engine-plus-heat exchanger weight (minimum airplane gross weight) for a range of heat-exchanger effective wall temperature."

Report presenting a wind-tunnel investigation to explore the merits of split and chord-extension flaps on a 45 degree sweptback wing. Testing occurred at low speed on a semispan model equipped with split flaps of 60 and 90-percent span and a full-span chord-extension flap. Results regarding split flaps, chord-extension flap, and resultant lift coefficients after balancing pitching-moment coefficients are provided.

Report presenting an investigation of the two-dimensional aerodynamic characteristics of several NACA airfoil sections at four Reynolds numbers. Results regarding the minimum drag, maximum lift, lift-curve slope, and angle of zero lift and pitching moment are provided.

From Introduction: "The intermediate subsonic speed range is considered and the liquid-metal turbine-propeller cycle discussed in this report. In this report, compressor pressure ratio, heat-exchanger air-inlet Mach number, and turbine-inlet temperature were optimized for maximum engine net thrust per engine-plus-heat-exchanger weight (minimum airplane gross weight) for a range of heat-exchanger effective wall temperature."

Report presenting preliminary results of one phase of a control-motion study program using data obtained from 276 maneuvers performed using a McDonnell F2H-2 jet fighter airplane during normal squadron operational training. Results regarding classification of maneuvers, airspeed, load factors, sideslip angle, and maximum pitching-, rolling-, and yawing-angular-acceleration variations with indicated airspeed are provided.

"The solution of Von Karman's fundamental equations for large deflections of plates is presented for the case of a simply supported rectangular plate under combined edge compression and lateral loading. Numerical solutions are given for square plates and for rectangular plates with a width-span ratio of 3:1. The effective widths under edge compression are compared with effective widths according to Von Karman, Bengston, Marguerre, and Cox and with experimental results by Ramberg, Mcpherson, and Levy" (p. 1).

"Values of the circulation function have been obtained for dual-rotating propellers. Numerical values are given for four, eight, and twelve-blade dual-rotating propellers and for advance ratios from 2 to about 6. In addition, the circulation function has been determine for single-rotating propellers for the higher values of the advance ratio. The mass coefficient, another quantity of significance in propeller theory, has been introduced" (p. 35).

Report presents the results of an investigation conducted to determine the effectiveness of liquid-cooling films on the inner surfaces of tubes containing flowing hot air. Experiments were made in 2- and 4-inch-diameter straight metal tubes with air flows at temperatures from 600 degrees to 2000 degrees F. and diameter Reynolds numbers from 2.2 to 14 x 10(5). The film coolant, water, was injected around the circumference at a single axial position on the tubes at flow rates from 0.02 to .24 pound per second per foot of tube circumference (0.8 to 12 percent of the air flow). Liquid-coolant films were established and maintained around and along the tube wall in concurrent flow with the hot air. The results indicated that, in order to film cool a given surface area with as little coolant flow as possible, it may be necessary to limit the flow of coolant introduced at a single axial position and to introduce it at several axial positions. The flow rate of inert coolant required to maintain liquid-film cooling over a given area of tube surface can be estimated when the gas-flow conditions are known by means of a generalized plot of the film-cooling data.

Report presenting an investigation at Mach number 1.62 of a series of triangular wing and body combinations to determine the interference lift, drag, and pitching moment. Testing was conducted on seven flat-plate triangular wings of varying scale, four with a half-apex angle of 30 degrees and three with a half-apex angle of 45 degrees. Results regarding wing alone, wing in the presence of the body, basic quantities for interference evaluation, interference quantities, and contributions of both types of quantities are provided.

Report presenting an investigation of the effects of streamwise gaps between wing and body on the lift and pitching moments of a moderately slender wing-body combination at Mach number 1.4 and compared with available theoretical results. The investigation included tests in which the angle of attack is varied with the all-movable wing at zero deflection and also tests at which the angle of wing deflection is varied with the body at zero angle of attack.

Report presenting some work done to meet the requirements of missile control designers for more powerful controls and for lower hinge moments. Some testing regarding all-movable wings and reducing hinge moments is described.

Report presenting longitudinal and lateral-directional frequency responses determined from transient flight data excited by control pulses for a large flexible swept-wing airplane over a wide range of flight conditions. The effects of structural modes on the frequency response at various locations on the airplane are shown. Results regarding the low-frequency response, longitudinal transfer-function coefficients, lateral response, lateral-directional transfer-function coefficients, experimental technique, and high-frequency responses are provided.

Memorandum presenting an investigation of the possibility of correlating airfoil section data with measured pressure distributions over a 45 degree sweptback wing in the Mach number range from 0.50 to 0.95 at a free-stream Reynolds number of approximately 2 million. The wing had an aspect ratio of 5.5, a taper ratio of 0.53, NACA 64A010 sections normal to the quarter-chord line, and was mounted on a slender body of revolution. Results regarding correlation of chordwise pressure distributions, correlation of magnitudes of section loads, and wing-body characteristics are provided.

"Experimental results on the effect of the length-diameter ratio of the orifice on the spray characteristics, together with a brief analysis of the factors affecting these characteristics, are presented in this report. The length-diameter ratios tested ranged from 0.5 to 10; the orifice diameters from 0.008 to 0.040 inch; and the injection pressures from 2,000 to 8,000 pounds per square inch. The density of the air into which the fuel was discharged was varied from 0.38 to 1.35 pounds per cubic foot" (p. 79).