This report gives the results of the tests of seven 2 by 12 foot airfoils (Clark Y, smooth and corrugated, Gottingen 398, N.A.C.A. M-6, and N.A.C.A. 84). The tests were made in the propeller research tunnel of the National Advisory Committee for Aeronautics at Reynolds numbers up to 2,000,000. The Clark Y airfoil was tested with three degrees of surface smoothness. Corrugating the surface causes a flattening of the lift curve at the burble point and an increase in drag at small flying angles.

The data given in this report covers the explosive limits of hydrocarbon fuels. Incidental to the purpose of the investigation here reported, the explosive limits will be found to be expressed for the condition of constant pressure, in the fundamental terms of concentrations (partial pressures) of fuel and oxygen.

"An investigation conducted to determine the factors which control the combustion in a high-speed compression-ignition engine is presented. Indicator cards were taken with the Farnboro indicator and analyzed according to the tangent method devised by Schweitzer. The analysis show that in a quiescent combustion chamber increasing the time lag of auto-ignition increases the maximum rate of combustion. Increasing the maximum rate of combustion increases the tendency for detonation to occur" (p. 63).

"Experimental results on the effect of the length-diameter ratio of the orifice on the spray characteristics, together with a brief analysis of the factors affecting these characteristics, are presented in this report. The length-diameter ratios tested ranged from 0.5 to 10; the orifice diameters from 0.008 to 0.040 inch; and the injection pressures from 2,000 to 8,000 pounds per square inch. The density of the air into which the fuel was discharged was varied from 0.38 to 1.35 pounds per cubic foot" (p. 79).

The object of this investigation was to determine the effect of increasing the carburetor pressures from 30 to 40 inches of mercury, at compression ratios from 3.5 to 7.5, on the power, on the maximum cylinder pressures, on the fuel consumption, and on the other performance characteristics of an engine. A roots-type aircraft-engine supercharger was used to maintain the desired carburetor pressure.

This report presents the results of an investigation to determine experimentally the instantaneous pressures at the discharge orifice of a common-rail fuel injection system in which the timing valve and cut-off valve were at some distance from the automatic fuel injection valve, and also to determine the methods by which the pressure fluctuations could be controlled. The results show that pressure wave phenomena occur between the high-pressure reservoir and the discharge orifice, but that these pressure waves can be controlled so as to be advantageous to the injection of the fuel. The results also give data applicable to the design of such an injection system for a high-speed compression-ignition engine.

The investigation described in this report was conducted for the purpose of comparing an oleo-rubber-disk and a rubber-cord landing gear, built for use on an F6C-4 airplane. The investigation consisted of drop tests under various loading conditions and flight tests on an F6C-4 airplane. In the drop tests the total work done on each gear and the work done on each of the shock-absorbing units were determined. For both drop tests and flight tests the maximum loads and accelerations were determined. The comparative results showed that the oleo gear was slightly superior in reducing the ordinary landing shocks, that it had a greater capacity for work, and that it was very superior in the reduction of the rebound. The results further showed that for drops comparable to very severe landings, the rubber-cord gear was potentially more effective as a shock-reducing mechanism. However, due to the construction of this chassis, which limited the maximum elongation of the cords, this gear was incapable of withstanding as severe tests as the oleo gear. The action of the oleo gear was greatly inferior to the action of an ideal gear. The maximum accelerations encountered during the flight tests for severe landings were 3.64g for …

"This reports presents the results of pressure distribution tests on a thick, tapered and twisted monoplane wing model. The investigation was conducted for the purpose of obtaining data on the aerodynamic characteristics of the new wing and to provide additional information suitable for use in the design of tapered cantilever wings. The tests included angles of attack up to 90 degrees. The span loading over the wing was approximately of elliptical shape, which gave rise to relatively small bending moments about the root" (p. 97).

"This investigation was made for the purpose of obtaining information on the maneuverability of the F6C-3 airplane. It is the first of a series of similar investigations to be conducted on a number of military airplanes for the purpose of comparing the abilities of these airplanes to maneuver, and also to establish a fund of quantitative data which may be used in formulating standards of comparison for rating the maneuverability of any airplane. A large part of this initial investigation was necessarily devoted to the development and trial of methods suitable for use in subsequent investigations of this nature" (p. 117).

This report presents the first part of a two part study made under this title. In this part the symmetrical inviscid flow about an empirical strut of high service merit is found by both the Rankine and the Joukowsky methods. The results can be made to agree as closely as wished. Theoretical stream surfaces as well as surfaces of constant speed and pressure in the fluid about the strut are found. The surface pressure computed from the two theories agrees well with the measured pressure on the fore part of the model but not so well on the after part. From the theoretical flow speed the surface friction is computed by an empirical formula. The drag integrated from the friction and measured pressure closely equals the whole measured drag. As the pressure drag and the whole drag are accurately determined, the friction formula also appears trustworthy for such fair shapes. (author).

"This investigation describes a visual method for making stroboscopic observations, through a large number of small windows, of the spread of flame throughout the combustion chamber of a gasoline engine. Data, secured by this method on a small engine burning gaseous fuels, are given to show the effects of mixture ratio, spark advance, engine speed, charge density, degree of dilution, compression ratio, and fuel composition on flame movement in the cylinder. Partial indicator diagrams showing pressure development during the combustion period are included" (p. 697).

"Apparatus for recording photographically the start, growth, and cut-off of oil sprays from injection valves has been developed at the Langley Memorial Aeronautical Laboratory. The apparatus consists of a high-tension transformer by means of which a bank of condensers is charged to a high voltage. The controlled discharge of these condensers in sequence, at a rate of several thousand per second, produces electric sparks of sufficient intensity to illuminate the moving spray for photographing. The sprays are injected from various types of valves into a chamber containing gases at pressures up to 600 pounds per square inch" (p. 361).

"This report combines the wind tunnel results of tests on four control surface models made in the two wind tunnels of the Navy Aerodynamic Laboratory, Washington Navy Yard, during the years of 1922 and 1924, and submitted for publication to the National Advisory Committee for Aeronautics May 7, 1927. The purpose of the tests was to compare, first, the lifts and the aerodynamic efficiencies of the control surfaces from which their relative effectiveness as tail planes could be determined; then the elevator hinge moments upon which their relative ease of operation depended. The lift and drag forces on the control surface models were obtained for various stabilizer angles and elevator settings in the 8 by 8 foot tunnel by the writer in 1922; the corresponding hinge moments were found in the 4 by 4 foot tunnel by Mr. R. M. Bear in 1924" (p. 429).

The laws of comparison of dynamically similar fluid motions are derived by three different methods based on the same principle and yielding the same or equivalent formulas. This report outlines the three current methods of comparing dynamically similar motions, more especially of fluids, initiated respectively by Newton, Stokes (or Helmholtz), and Rayleigh. These three methods, viz., the integral, the differential, and the dimensional, are enough alike to be studied profitably together. They are treated in succession then compared. (author).

"The rate of change in power of aircraft engines with altitude has been the subject of considerable discussion. Only a small amount of data from direct measurements of the power delivered by airplane engines during flight, however, has been published. This report presents the results of direct measurements of the power delivered by a Liberty 12 airplane engine taken with a hub dynamometer at standard altitudes from zero to 13,000 feet. Six flights were made with the engine installed in a modified DH-4 airplane" (p. 323).

"This report covers the results of an investigation carried on at the Bureau of Standards under a research authorization from, and with the financial assistance of, the National Advisory Committee for Aeronautics. The choice of a damping liquid for aircraft instruments is difficult owing to the range of temperature at which aircraft operate. Temperature changes affect the viscosity tremendously. The investigation was undertaken with the object of finding liquids of various viscosities otherwise suitable which had a minimum change in viscosity with temperature" (p. 405).

Report presents the design of radiators, spark plugs and test equipment used to test the performance of aeronautic engines at high altitudes.

The National Bureau of Standards tested a 300-horsepower Hispano-Suiza engine to determine the characteristic performance of the engine at various altitudes. The engine was operated at the ground, at 25,000 feet, and at intermediate altitudes, both at full loads similar to those that would be imposed upon the engine at various speeds by a propeller whose normal full-load speed was 1,800 r.p.m. Friction horsepower also was determined in order that the mechanical efficiency of the engine might be calculated.

From Summary: "The report includes a description of the commonly used types and some others, the underlying principle utilized in the design, and some design data. The inherent errors of the instrument, the methods of making laboratory tests, descriptions of the test apparatus, and data in considerable detail in the performance of commonly used instruments are presented. Standard instruments and, in cases where it appears to be of interest, those used as secondary standards are described."

An analysis of the longitudinal characteristics of swept wings which is based on available large-scale low-speed data and supplemented with low-scale data when feasible is presented. The emphasis has been placed on the differentiation of the characteristics by a differentiation between the basic flow phenomenon involved. Insofar as possible all large-scale data available as of August 15, 1951 have been summarized in tabular form for ready reference.

For a body consisting of a fineness-ratio-3 ogival nose tangent to a cylindrical afterbody 7.3 diameters long, pitot-pressure distributions in the flow field, pressure distributions over the body, and downwash distributions along a line through the vortex centers have been measured for angles of attack to 20 degrees. The Reynolds numbers, based on body diameter, were 0.15 x 10 to the 6th power and 0.44 x 10 to the 6th power. Comparisons of computed and measured vortex paths and downwash distributions are made. (author).

"The well-known methods of thin-airfoil theory have been extended to oblique or sweptback airfoils of finite aspect ratio moving at supersonic speeds. The cases considered thus far are symmetrical airfoils at zero lift having plan forms bounded by straight lines. Because of the conical form of the elementary flow fields, the results are comparable in simplicity to the results of the two-dimensional thin-airfoil theory for subsonic speeds" (p. 267).

"This paper presents a mathematical discussion of the laminar boundary layer, which was developed with a view of facilitating the investigation of those boundary layers in particular for which the phenomenon of separation occurs. The treatment starts with a slight modification of the form of the boundary layer equation first published by Von Mises. Two approximate solutions of this equation are found, one of which is exact at the outer edge of the boundary layer while the other is exact at the wall" (p. 541).

This report is the second of a series giving the results obtained in the 20-foot wind tunnel of the National Advisory Committee for Aeronautics on the interference drag and propulsive efficiency of nacelle-propeller-wing combinations. The first report gave the results of the test of a N.A.C.A. cowled air-cooled engine nacelle located in 21 positions with reference to a thick wing. The present report gives results of tests of a normal engine nacelle with several types of cowling and fairings in four of the positions with reference to the same wing. (author).