Report presenting the air-flow behavior over the wing of an XP-51 airplane including photographs of tufts attached to the wing surface and chordwise pressure distributions. A comparison of tuft studies from flight results are compared with results from wind-tunnel testing. Three types of flow were observed: steady flow, unsteady flow, and break-away flow are provided.

"The XF-12 airplane was designed by Republic Aviation Corporation to provide the Army Air Forces with a high performance, photo reconnaissance aircraft. A series of air-stream surveys were made n the vicinity of the empennage of a 1/8.33-scale powered model of the XF-12 airplane in the Langley 19-foot pressure tunnel. Surveys of the vortical-tail region were made through a range of yaw angles of plus or minus 20 degrees at a high and low angle of attack" (p. 1).

"Investigations were conducted in the Cleveland altitude wind tunnel to determine the performance and operational characteristics of the 19B-2, 19B-8, and 19XS-1 turbojet engines. One objective was to determine the effect of altitude, flight Mach number, and tail-pipe-nozzle area on the performance characteristics of the six-stage and ten-stage axial-flow compressors of the 19B-8 and 19XB-1 engines, respectively, The data were obtained over a range of simulated altitudes and flight Mach numbers" (p. 1).

The performance characteristics of the 19B-8 and 19XB-1 turbojet engines and the windmilling-drag characteristics of the 19B-6 engine were determined in the Cleveland altitude wind tunnel. The investigations were conducted on the 19B-8 engine at simulated altitudes from 5000 to 25,000 feet with various free-stream ram-pressure ratios and on the 19XB--1 engine at simulated altitudes from 5000 to 30,000 feet with approximately static free-stream conditions.

Note presenting an analysis that was undertaken as part of an investigation of low-density fibrous core materials for sandwich construction. This particular investigation found that honeycomb structure exhibit promise as core materials because of their high strength-weight ratios. A formula has been derived that considerably reduced the amount of testing necessary to evaluate the effectiveness of the materials.

From Introduction: "An investigation was made to determine the relative significance of the factors that affect the exhaust process; the effects that an exhaust-process change has on cylinder charging were given special attention. Differential equations of this nature have been developed by Kemble (reference 1) but the forms of these equations are such that general conclusions regarding the various factors affecting the exhaust process cannot be determined."

Report presenting the combustion efficiencies of 10 experimental jet-propulsion fuels that are approximately 200 degrees Fahrenheit cuts of five selected crudes available in large quantities in a turbojet engine combustor at altitude conditions.

The feasibility of measuring the vibration in the buckets of a gas turbine under service conditions of speed and temperature was determined by use of a high temperature wire strain gauge cemented to a modified supercharger turbine bucket. A high-temperature wire strain gauge and the auxiliary mechanical and electrical equipment developed for the investigation are described.

"In conjunction with assumptions concerning the proportion of time spent at various speeds, statistical gust data were used to determine gust load factors that could be exceeded a given number of times during the operational life of an airplane. The results indicated that present gust load factors might be considerably lowered in certain cases with a consequent decrease in structural weight. Modification of the present criterion, however, must await the accumulation of data not presently available" (p. 1).

From Summary: "Previous tests of blower-blade sections have been extended by a series of tests at 52.5 degrees stagger. The results of these tests have been combined with the earlier test results and are presented in new blade design charts which supersede those previously presented. An investigation in a test blower over a range of stagger from 44 degrees to 65 degrees has shown that for blades at a solidity of 1.0, the two-dimensional cascade data predict the turning angle to within 1/2 degrees."

From introduction: The fundamental purpose of the laboratory is to provide research and training facilities in nuclear and related studies which are not possible for the individual University.

Report presenting a method for calculating the drag, in a real compressible fluid and at subcritical Mach numbers, of airfoil sections at arbitrary life coefficients and of bodies of revolution at zero angle of attack. The values of drag coefficient are compared with values obtained for the same configurations by other methods. The differences between the results are found to lie withint he limits of accuracy of current experimental techniques.

Report presenting an investigation of surface static pressures over the outer and inner surfaces of the cockpit canopies on the Grumman F6F-3, Curtiss SB2C-4E, and Grumman F8F-1 airplanes in the full-scale tunnel. Results regarding the external pressure distribution and internal static pressure are provided.

Report presenting an analysis of wind-tunnel data on the hinge-moment characteristics of control-surface tabs. Results regarding the correlation of section data, correlation of finite-span data, and effect of Mach number are provided.

"While the gas turbine by itself has been applied in particular cases for power generation and is in a state of promising development in this field, it has already met with considerable success in two cases when used as an exhaust turbine in connection with a centrifugal compressor, namely, in the supercharging of combustion engines and in the Velox process, which is of particular application for furnaces. In the present paper the most important possibilities of combining a combustion engine with a gas turbine are considered. These "combination engines " are compared with the simple gas turbine on whose state of development a brief review will first be given" (p. 1).

Report presenting comparative drag measurements at zero lift at transonic speeds for two sharp-leading-edge airfoils using the NACA wing-flow method. One airfoil had a symmetrical circular-arc section and one had a symmetrical double-wedge section. The primary difference in the drag characteristics of the two airfoils at zero lift is the earlier drag rise of the double-wedge section.

Report presenting a comparison of the maximum amount of transverse righting moment at rest provided by auxiliary floats or stub wings for 25 seaplanes and the minimum righting moment required by certain design specifications. Large differences were found to exist between the specifications and 25 designs studied.

Report presenting comparisons of 24S-T aluminum-alloy flat compression panels with longitudinal Z-section stiffeners and panels with flat FS-1E magnesium-alloy sheet and longitudinal 24S-T aluminum-alloy Z-section stiffeners. The use of the composite magnesium-alloy, aluminum-alloy construction permits wider stiffener spacing with little to not loss in structural efficiency or stress for local buckling. Results regarding stiffener spacing, proportions, and consideration of the different material constructions are provided.

A theoretical analysis of the temperature distribution through the trailing portion of a blade near the coolant passages of liquid cooled gas turbines was made. The analysis was applied to obtain the hot spot temperatures at the trailing edge and influence of design variables. The effective gas temperature was varied from 2000 degrees to 5000 degrees F in each investigation.

Tests of a PB2Y-3 flying boat were made at the U.S. Naval Air Station, Patuxent River, Md., to determine its hydrodynamic trim limits of stability. Corresponding tests were also made of a 1/8-size powered dynamic model of the same flying boat in Langley tank no. 1. During the tank tests, the full-size testing procedure was reproduced as closely as possible in order to obtain data for a direct correlation of the results. As a nominal gross load of 66,000 pounds, the lower trim limits of the full-size and model were in good agreement above a speed of 80 feet per second. As the speed decreased below 80 feet per second, the difference between the model trim limits and full-scale trim limits gradually became larger. The upper trim limit of the model with flaps deflected 0 deg was higher than that of the full-size, but the difference was small over the speed range compared. At flap deflections greater than 0 deg, it was not possible to trim either the model of the airplane to the upper limit with the center of gravity at 28 percent of the mean aerodynamic chord. The decrease in the lower trim limits with increase in flap …

The following report briefly covers broad general features of the chemical studies to be used by the Atomic Energy Commission in considering future work on the chemical studies of phosphate rock and shale.

"This report gives theoretical discussion of the distribution of leads on rivets connecting a plate to a beam under transverse leads. Two methods of solution are given which are applicable to loads up to the limit of proportionality; in the first the rivets are treated as discrete members, and in the second they are replaced by a continuous system of jointing. A method of solution is also given which is applicable to the case when nonlinear deformations occur in the rivets and the plate, but not in the beam" (p. 1).

Report presenting tests to determine the effect of sweepback angle and aspect ratio on the drag at supersonic speeds of wings of NACA 65-009 airfoil section. The current report is part of a bigger investigation and includes results for aspect ratios of 3.8 and 5.0. Results regarding the drag coefficient and general effect of aspect ratio are provided.

Report discussing the results of flight tests to determine the drag at zero lift of a swept-back wing of inverse taper using an NACA 65-009 airfoil. The data was compared to untapered wings with a similar degree of sweepback. The tapered wing was found to have a lower drag coefficient than the 34-degree swept-back untapered wing but a higher drag coefficient than the 45-degree swept-back untapered wing.