Report discussing an investigation to determine the effects of aeroelasticity on the rolling effectiveness of a model of a McDonnell F3H-1 airplane wing. The plane was found to be subject to aeroelastic losses that varied with Mach number and altitude.

Report discussing a project to determine a high-energy fuel suitable for turbojet-powered aircraft. Components of the project include thermal and combustion properties, experiments with combustors using boron compounds, evaluation of boron fuels in full-scale turbojets with and without afterburners, and boron fuel use in ramjet flights. The most promising fuel found in the report is pentaborane.

Combustion chamber liners for gas turbines and experimental set-ups were tested for failure. A ceramic-lined test chamber was operated at fuel/air ratios up to 0.050. Thermal-shock evaluation indicated that a ceramic lining, which expands after firing, would crack but would not fall apart during operation. Refractoriness of the lining and the resistance to mechanical shock were adequate. In general, shell temperature reductions of approximately 400 deg F were effected by the use of this lining at fuel/air ratios of 0.016 and 0.050. The mechanism of failure of the ceramic lining was induced by sudden heating and cooling during operation.

Report presenting information about some of the fundamental concepts and lines of development that may be undertaken regarding helicopter stability. Some of the principles discussed include method of control, control lag, stability characteristics, control forces, and center of gravity. Some of the means for improvement discussed include use of a horizontal stabilizer, use of trim devices, use of power-operated controls, automatic controls, and choice and grouping of indicating instruments.

From Introduction: "Analyses that provide a basis for comparing the centrifugal-stress distributions inherent in jet-engine turbine blades of several designs currently in use were therefore made and are presented."

Report presenting an investigation into the effect of end plates and end-mounted struts on the lift-drag ratios of a hydrofoil at several speeds and Reynolds numbers that were all above the limiting speed of wave propagation. Information about the lift-drag ratio, effective aspect ratio, and comparison of the results versus theoretical calculations is included.

Report presenting a survey of various types of catapults in connection with the problem of accelerating a large car along a track to a speed of 150 miles per hour. A hydraulic jet catapult seems to be the best-suited for the purpose, and various types of design problems are examined.

Report presenting an investigation of wings of aspect ratios of 4, 3, and 2 with a plan-form taper ratio of 0.5 and a thickness taper ratio of 0.33 to determine their transonic longitudinal characteristics and effects of tapering thickness ratio. Results regarding the combined effects of aspect ratio and thickness ratio and effects of tapered thickness ratio are provided.

Report presenting an investigation to determine the aerodynamic characteristics of a cruciform 70 degree delta-wing missile configuration with 70 degree delta canard control surfaces at M = 1.41 in the 4- by 4-foot supersonic pressure tunnel. Modifications to the configuration included variation of the body length and canard area and the substitution of a series of very small span wings for the cruciform delta wings and canard controls.

Report presenting an investigation to determine the effects of aeroelasticity on the rolling effectiveness of an 8.06-percent-scale model of the McDonnell F3H-1 airplane wing. The investigation used rocket-propelled models in free flight over a range of Mach numbers. The results indicate that the airplane is subject to aeroelastic losses varying from about 7 percent at Mach number 0.5 to 46 percent at Mach number 0.90 at sea level.

"An investigation at medium to high subsonic speeds has been conducted in the Langley low-turbulence pressure tunnel to determine the static stability and control characteristics and to measure the fin normal forces and moments for a model of a wingless fin-controlled missile. With the horizontal-fin deflection limited to a maximum of 6 degrees, longitudinally stable and trimmed flight could not be maintained beyond an angle of attack of 17 degrees for a Mach number of 0.88 and beyond 20 degrees for a Mach number of 0.50 for any center-of-gravity location without the use of some auxiliary stability or control device such as jet vanes" (p. 1).

Report presenting detailed blade-element-performance plots for a high-flow transonic inlet rotor. Information provided includes the effects of Mach number, blade loading, and angle of attack on element performance is provided.

Report presenting an investigation to determine the control hinge-moment characteristics at two Mach numbers for a series of 18 controls, including the effects of various tabs and fences, on a 60 degree delta wing. Testing covered a range of angles of attack, control deflection, and tab deflection. Results regarding the basic variation of hinge-moment coefficients, tip controls, and trailing-edge controls are provided.

Report presenting an investigation at Mach numbers from 0.6 to 1.28 to determine the drag characteristics of a series of conical afterbodies with a cold sonic jet issuing from the base. Models investigated had boattail angles from 3 to 45 degrees, ratios of jet diameter to base diameter of 0.65 and 0.75, and values of the ratios of the base diameter to maximum diameter of 0.55, 0.70, and 0.85. Results regarding afterbody pressure distributions and afterbody drag are provided.

Memorandum presenting a determination of the static lateral stability of six delta wings at subsonic speeds. In addition, two of the wings with 82.5 degree and 75 degree sweep of the leading edge were oscillated in yaw about the 50-percent point of the root chord in order to determine the effects of frequency and amplitude on the combination lateral stability derivatives resulting from the motion. Results regarding the static characteristics and oscillatory characteristics are provided.

Report presenting NACA work through 1954 on a high-energy fuel suitable for turbojet-powered aircraft. The work includes thermal and combustion properties, experiments with combustors designed to use boron compounds, evaluation of boron fuels in full-scale turbojets with and without afterburners, and ramjet flights on boron fuels. Satisfactory combustion of pentabornae and high-concentration blends of pentaborane has been demonstrated in a turbojet, an afterburner, and a ram jet.