Rapid advances in computer software offer may opportunities for increasing efficiency and productivity; however, choosing the right software package and achieving its full potential can be a challenging task. Lubrication engineers faced with the selection and implementation of a computer system will find that they can increase their chance of success when they follow the nine steps outlined in this paper. These steps provide a solid framework for managing the project through its full life-cycle from initial conception until final retirement of the system. Lubrication Departments that already have computer systems in place can also benefit from these steps by picking up at the corresponding point in the system's life and following the remaining steps.

The High Energy Transport Code, HETC, was obtained from the Radiation Shielding Information Center (RSIC) at Oak Ridge National Laboratory and altered as necessary to run on a CDC 7600 using the LTSS software in use at LLNL. HETC was then used to obtain calculated estimates of energy deposited, for comparison with a series of benchmark experiments done by LLNL. These experiments used proton beams of various energies incident on well-defined composite targets in good geometry. In this report, two aspects of the comparison between calculated and experimental energy depositions from an 800 MeV proton beam are discussed. Both aspects involve the fact that workers at SAI had previously used their version of HETC to calculate this experiment and reported their comparison with the measured data. The first aspect addressed is that their calculated data and LLNL calculations do not agree, suggesting an error in the conversion process from the RSIC code. The second aspect is not independent of the first, but is of sufficient importance to merit separate emphasis. It is that the SAI calculations agree well with experiments at the detector plate located some distance from the shower plate, whereas the LLNL calculations show a clearcut discrepancy there …

A CAMAC Serial Highway Interface has been designed for the Local Control and Instrumentation System of the Mirror Fusion Test Facility. There are over 50 distinguishable systems in the facility, each of which consists of the LSI-11 computer, fiber optic communication links, and the CAMAC system. The LSI-11 computer includes a 32k memory, serial modem interface and the CAMAC Serial Highway Interface.

In the program of development of a water treatment for the 5 MW Raft River power plants' carbon steel heat rejection system, four carbon steel tubes were analyzed in this batch. The results of visual and scanning electron microscope examination of the tubes are presented. (MHR)

Beam fractions lost by collimation in a neutralizer duct are computed in x-x' phase space by using three examples of slab beam distributions under a broad range of duct dimensions, beam half-widths, and beam divergences. The results can be used to design compact neutralizers and to specify beam requirements. The computer code ILOST can be used under a broad range of beam conditions to compute the fraction lost by collimation.

A serial communications system based on the EIA RS232-C standard with modem control lines has been developed. The DLV11-E interface is used for this purpose. All handshaking is done with the modem control lines. This allows totally independent full duplex communication. The message format consists of eight bit data with odd parity and a sixteen bit checksum on the whole message. All communications are fully interrupt driven. A program was written to load a program into a remote LSI-11 using the serial line without bootstrap ROM.

Bare fused silica surfaces were prepared by subjecting the mechanically polished surface to a rastered cw CO/sub 2/ laser beam. Analysis shows that this processing causes: (a) removal of a uniform layer of fused silica; and (b) a probable re-fusing or healing of existing subsurface fractures. The fused silica removal rate is found to be a function of the laser intensity and scan rate. These surfaces are seen to have very low scatter and to be very smooth. In addition, they have exhibited entrance surface damage thresholds at 1.06 ..mu..m, and 1 nsec, which are substantially above those seen on the mechanically polished surface. When damage does occur, it tends to be at a few isolated points rather than the general uniform damage seen on the mechanicaly polished part. In addition to the damage results, we will discuss an observational technique used for viewing these surfaces which employs dark-field illumination.

Plasma physics and engineering models of tandem mirror devices operated with a high-field technology test-cell insert in the central cell, which have been incorporated recently in the TMRBAR tandem mirror reactor physics code, are described. The models include particle and energy balance in the test-cell region as well as the interactions between the test-cell particles and those flowing through the entire device. The code calculations yield consistent operating parameters for the test-cell, central cell, and end cell systems. A benchmark case for the MFTF-..cap alpha..+T configuration is presented which shows good agreement between the code results and previous calculations.

None

Cancer cells are endowed with diverse biological capabilities driven by myriad inherited and somatic genetic and epigenetic aberrations that commandeer key cancer-relevant pathways. Efforts to elucidate these aberrations began with Boveri's hypothesis of aberrant mitoses causing cancer and continue today with a suite of powerful high-resolution technologies that enable detailed catalogues of genomic aberrations and epigenomic modifications. Tomorrow will likely bring the complete atlas of reversible and irreversible alteration in individual cancers. The challenge now is to discern causal molecular abnormalities from genomic and epigenomic 'noise', to understand how the ensemble of these aberrations collaborate to drive cancer pathophysiology. Here, we highlight lessons learned from now classical examples of successful translation of genomic discoveries into clinical practice, lessons that may be used to guide and accelerate translation of emerging genomic insights into practical clinical endpoints that can impact on practice of cancer medicine.

This Geotechnical Analysis Report (GAR) presents and interprets the geotechnical data from the underground excavations at the Waste Isolation Pilot Plant (WIPP). The data, which are obtained as part of a regular monitoring program, are used to characterize conditions, to compare actual performance to the design assumptions, and to evaluate and forecast the performance of the underground excavations. GARs have been available to the public since 1983. During the Site and Preliminary Design Validation (SPDV) Program, the architect/engineer for the project produced these reports quarterly to document the geomechanical performance during and immediately after early excavations of the underground facility. Since the completion of the construction phase of the project in 1987, the management and operating contractor for the facility has prepared these reports annually. This report describes the performance and condition of selected areas from July 1, 2004, to June 30, 2005. It is divided into nine chapters. Chapter 1 provides background information on WIPP, its mission, and the purpose and scope of the Geomechanical Monitoring Program. Chapter 2 describes the local and regional geology of the WIPP site. Chapters 3 and 4 describe the geomechanical instrumentation in the shafts and shaft stations, present the data collected by that …

The genomes of many epithelial tumors exhibit extensive chromosomal rearrangements. All classes of genome rearrangements can be identified using End Sequencing Profiling (ESP), which relies on paired-end sequencing of cloned tumor genomes. In this study, brain, breast, ovary and prostate tumors along with three breast cancer cell lines were surveyed with ESP yielding the largest available collection of sequence-ready tumor genome breakpoints and providing evidence that some rearrangements may be recurrent. Sequencing and fluorescence in situ hybridization (FISH) confirmed translocations and complex tumor genome structures that include coamplification and packaging of disparate genomic loci with associated molecular heterogeneity. Comparison of the tumor genomes suggests recurrent rearrangements. Some are likely to be novel structural polymorphisms, whereas others may be bona fide somatic rearrangements. A recurrent fusion transcript in breast tumors and a constitutional fusion transcript resulting from a segmental duplication were identified. Analysis of end sequences for single nucleotide polymorphisms (SNPs) revealed candidate somatic mutations and an elevated rate of novel SNPs in an ovarian tumor. These results suggest that the genomes of many epithelial tumors may be far more dynamic and complex than previously appreciated and that genomic fusions including fusion transcripts and proteins may be common, possibly yielding tumor-specific …

Eight different polymer binders were formulated with bimodal distributions of 2,6-diamino-3,5-dinitropyrazine-1-oxide (LLM-105) in 5/95 weight ratio of polymer to explosive at the 25 gram level. The polymers evaluated included: Kel-F 800, Viton A, Oxy 461, Cytop A, Hyflon AD 60, Hytemp 5545, Technoflon PFR 91 and Technoflon P 459. LLM-105 had an average particle size of 35.6 {+-} 0.6 {micro}m. This material was ground in a ball mill for 24 h to achieve a particle size of 0.72 {+-} 0.02 {micro}m. Small angle light scattering measurements were used to obtain particle size distributions on both ground and unground LLM-105. Optical microscopy was used to characterize the morphology of the crystals. Bimodal mixes of approximately 75/25% coarse to fine LLM-105 were used in all formulations. Cylinders 1.27 cm diameter by 2.54 cm long were compression molded using 3 three-minute cycles at 105 C, except in the case of Cytop and Hyflon formulations which were molded at {approx}130 C. Densities varied between 94-98% of theoretical maximum. Stress strain measurements were made in compression at -30, ambient and 74 C at a strain rate of 0.0001 sec{sup -1}. As expected, the mechanical strength scaled with temperature depending on the glass transition temperature of …

The U.S. fusion energy program is focused on research with the potential for studying plasmas at thermonuclear temperatures, currently epitomized by the tokamak-based International Thermonuclear Experimental Reactor (ITER) but also continuing exploratory work on other plasma confinement concepts. Among the latter is the spheromak pursued on the SSPX facility at LLNL. Experiments in SSPX using electrostatic current drive by coaxial guns have now demonstrated stable spheromaks with good heat confinement, if the plasma is maintained near a Taylor state, but the anticipated high current amplification by gun injection has not yet been achieved. In future experiments and reactors, creating and maintaining a stable spheromak configuration at high magnetic field strength may require auxiliary current drive using neutral beams or RF power. Here we show that neutral beam current drive soon to be explored on SSPX could yield a compact spheromak reactor with current drive efficiency comparable to that of steady state tokamaks. Thus, while more will be learned about electrostatic current drive in coming months, results already achieved in SSPX could point to a productive parallel development path pursuing auxiliary current drive, consistent with plans to install neutral beams on SSPX in the near future. Among possible outcomes, spheromak research …

None

The Clostridial neurotoxins, botulinum and tetanus, gain entry into neuronal cells by protein recognition involving cell specific binding sites. The sialic or N-acetylneuraminic acid (NeuAc) residues of gangliosides attached to the surface of motor neurons are the suspected recognition and interaction points with Clostridial neurotoxins, although not necessarily the only ones. We have used electrospray ionization mass spectrometry (ESIMS) to examine formation of complexes between the tetanus toxin C fragment, or targeting domain, and carbohydrates containing NeuAc groups to determine how NeuAc residues contribute to ganglioside binding. ESI-MS was used to rapidly and efficiently measure dissociation constants for a number of related NeuAc-containing carbohydrates and NeuAc oligomers, information that has helped identify the structural features of gangliosides that determine their binding to tetanus toxin. The strength of the interactions between the C fragment and (NeuAc){sub n}, are consistent with the topography of the targeting domain of tetanus toxin and the nature of its carbohydrate binding sites. The results suggest that the targeting domain of tetanus toxin contains two binding sites that can accommodate NeuAc (or a dimer). This study also shows that NeuAc must play an important role in ganglioside binding and molecular recognition, a process critical for normal cell …

This 7th quarterly Technical Progress Report for the Lignite Fuel Enhancement Project summarizes activities from January 1st through March 31st of 2006. It also summarizes the subsequent purchasing activity, dryer/process construction, and testing. The Design Team began conferencing again as construction completed and the testing program began. Primary focus this quarter was construction/installation completion. Phase 1 extension recommendation, and subsequent new project estimate, Forms 424 and 4600 were accepted by DOE headquarters. DOE will complete the application and amended contract. All major mechanical equipment was run, checked out, and tested this quarter. All water, air, and coal flow loops were run and tested. The system was run on January 30th, shut down to adjust equipment timing in the control system on the 31st, and run to 75 ton//hour on February 1st. It ran for seven to eight hours per day until March 20th when ''pairs'' testing ( 24 hour running) began. ''Pairs'' involves comparative testing of unit performance with seven ''wet'' pulverizers versus six ''wet'' and one ''dry''. During the interim, more operators were brought up to speed on system operation and control was shifted to the main Unit No.2 Control Room. The system is run now from the Unit …

This report is a compilation of work done over the past ten years in support of phase stability studies of Alloy 22 for the Yucca Mountain Project and contains information previously published, reported, and referenced. Most sections are paraphrased here for the convenience of readers. Evaluation of the fabrication processes involved in the manufacture of waste containers is important as these processes can have an effect on the metallurgical structure of an alloy. Because material properties such as strength, toughness, aging kinetics and corrosion resistance are all dependent on the microstructure, it is important that prototypes be built and evaluated for processing effects on the performance of the material. Of particular importance are welds, which have an as-cast microstructure with chemical segregation and precipitation of complex phases resulting from the welding process. The work summarized in this report contains information on the effects of fabrication processes such as solution annealing, stress mitigation, heat-to-heat variability, and welding on the kinetics of precipitation, mechanical, and corrosion properties. For a waste package lifetime of thousands of years, it is impossible to test directly in the laboratory the behavior of Alloy 22 under expected repository conditions. The changes that may occur in these materials …

Groundwater beneath T-Area, a former laboratory and semiworks operation at the Department of Energy (DOE) Savannah River Site, is contaminated by chlorinated solvents (cVOCs). Since the contamination was detected in the 1980s, the cVOCs at T-Area have been treated by a combination of soil vapor extraction and groundwater pump and treat. The site has received approval to discontinue the active treatments and implement a full scale test of enhanced attenuation--an engineering and regulatory strategy that has recently been developed by DOE and the Interstate Technology and Regulatory Council. Enhanced attenuation uses active engineering solutions to alter the target site in such a way that the contaminant plume will passively stabilize and shrink and to document that the action will be effective, timely, and sustainable. The paradigm recognizes that attenuation remedies are fundamentally based on a mass balance. Thus, long-term plume dynamics can be altered either by reducing the contaminant loading from the source or by increasing the rate of natural attenuation processes within all, or part of, the plume volume. The combination of technologies that emerged for T-Area included: (1) neat (pure) vegetable oil deployment in the deep vadose zone in the former source area, (2) emulsified vegetable oil deployment …

The pressure dependence of the Raman shift of diamond for highly stressed anvils at the diamond-anvil sample interface has been measured for different culet shapes up to 180 GPa at ambient temperature. By using hydrogen samples, which constitute both a quasi-hydrostatic medium and a sensitive pressure sensor, some of the effects of culet and tip size have been determined. We propose that the divergent results in the literature can be partly ascribed to different anvil geometries. Experiments show increasing second order dependence of the diamond Raman shift with pressure for decreasing tip size. This is an important consideration when using the diamond anvils as a pressure sensor.

Using both the absolute and relative surrogate techniques, the {sup 236}U(n,f) cross section was deduced over an equivalent neutron energy range of 0 to 20 MeV. A 42 MeV {sup 3}He beam from the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory was used to perform a ({sup 3}He,{alpha}) pickup reaction on targets of {sup 235}U (J{sup {pi}}=7/2{sup -}) and {sup 238}U (J{sup {pi}}=0{sup +}) and the fission decay probabilities were determined. The {sup 235}U({sup 3}He,{alpha}f) and {sup 238}U({sup 3}He,{alpha}f) were surrogates for {sup 233}U(n,f) and {sup 236}U(n,f), respectively. The cross sections extracted using the Surrogate Method were compared to directly measured cross sections. The sensitivity of these cross sections to the J{sup {pi}}-population distributions was explored.

This Geotechnical Analysis Report (GAR) presents and interprets geotechnical data from the underground excavations at the Waste Isolation Pilot Plant (WIPP). The data, which are obtained as part of a regular monitoring program, are used to characterize conditions, to compare actual performance to the design assumptions, and to evaluate and forecast the performance of the underground excavations. GARs have been available to the public since 1983. During the Site and Preliminary Design Validation (SPDV) Program, the architect/engineer for the project produced these reports quarterly to document the geomechanical performance during and immediately after early excavations of the underground facility. Since completion of the construction phase of the project in 1987, the management and operating contractor for the facility has prepared these reports annually. This report describes the performance and condition of selected areas from July 1, 2005, to June 30, 2006. It is divided into nine chapters. Chapter 1 provides background information on WIPP, its mission, and the purpose and scope of the geomechanical monitoring program. Chapter 2 describes the local and regional geology of the WIPP site. Chapters 3 and 4 describe the geomechanical instrumentation in the shafts and shaft stations, present the data collected by that instrumentation, and …

It has been known for a hundred years that formaldehyde polymerizes to carbohydrate substances in alkaline media. Although the reaction has long attracted much attention, only recently has a detailed qualitative analysis of the products been carried out by chromatographic methods. We have started to re-examine this reaction by combining chromatography with radioactive tracer techniques in the hope of refining the quantitative aspects of the analysis. Our particular interest has been to develop methods for determining the relative proportions of ribose and ribulose in the mixtures of sugars formed in basic media, as well as under other polymerizing conditions. The finding of large amounts of these sugars might help to explain the occurrence of ribose as the only basic sugar in the fundamental replicating molecules--the nucleic acids. Formaldehyde is thought to have been present in the primitive reducing atmosphere which existed before life first appeared. The ribonucleic acids must have appeared in the constitution of reproducing systems at a very early stage in the development of living organisms. In this study, the polymerizations of formaldehyde were carried out in calcium hydroxide suspensions at 40{sup o}. Aliquots of the reaction mixtures were withdrawn at after various time intervals and the alkali …

Projection optical systems built for Extreme Ultraviolet Lithography (EUVL) demonstrated the ability to produce, support and position reflective optical surfaces for achieving transmitted wavefront errors of 1 nm or less. Principal challenges included optical interferometry, optical manufacturing processes, multi-layer coating technology and opto mechanics. Our group was responsible for designing, building and aligning two different projection optical systems: a full-field, 0.1 NA, four-mirror system for 70 nm features and a small-field, 0.3 NA, two-mirror system for 30 nm features. Other than physical size and configuration, the two systems were very similar in the way they were designed, built and aligned. A key difference exists in the optic mounts, driven primarily by constraints from the metrology equipment used by different optics manufacturers. As mechanical stability and deterministic position control of optics will continue to play an essential role in future systems, we focus our discussion on opto-mechanics and primarily the optic mounts.