From Introduction: "Presented in this paper are the results of an investigation of a semispan model of a delta wing with 60^o sweepback at the leading edge which was equipped with a large triangular control having an overhang balance mounted on a skewed hinge axis. The purpose of this investigation was to determine the aerodynamic characteristics of a delta wing with a control which was designed to provide aerodynamic balance at zero control deflection based on the span load distribution of reference 1."

From Introduction: "The wings were tested in combination with fuselage similar to the one used in the 7- by 10-foot wind-tunnel investigations. The results are reported herein and are compared with results for three similar model wings on the transonic bump (references 1, 2, and 3)."

Report presenting a direct-connect altitude test chamber investigation of the combustion performance of a 28-inch-diameter ramjet engine with a can-type center pilot burner. Combustion-chamber configurations with three different flame holders were investigated at a simulated flight Mach number of 2.0 and several different altitudes.

Memorandum presenting an analysis made to estimate the performance of a direct-air nuclear turbojet-powered airplane using a split-flow reactor and a separated-type shield. The analysis was for flight Mach numbers of 0.9 and 1.5 and covered a range of altitudes, reactor-wall temperatures, turbine-inlet temperatures, compressor pressure ratios, and airplane lift-drag ratios.

Memorandum presenting an analysis made to estimate the performance of a direct-air nuclear turbojet-powered airplane with a split-flow reactor and a separated-type shield. The analysis was for flight Mach numbers of 0.9 and 1.5 and covered a range of altitudes, reactor-wall temperatures, turbine-inlet temperatures, compressor pressure ratios, and airplane lift-drag ratios.

Report presenting an investigation to determine the stability and control characteristics of a vertically rising airplane model. Results of preliminary hovering flight tests are made in still air, away from the interference effects of the ground and side walls, and with normal airplane-type controls operating in the slipstream.

Report presenting an investigation of the effects of three centrally mounted wing-tip tanks on the aerodynamic characteristics of a cambered wing with an aspect ratio of 10 and 35 degrees of sweepback. Testing occurred over a range of Mach and Reynolds numbers and lift, drag, and pitching-moment were measured.

Report presenting a wind-tunnel investigation to determine the effects of a section modification on the aerodynamic characteristics of a wing with 35 degrees of sweepback. The wing was modified by increasing the leading-edge radius of the NACA 64A010 section and adding a small amount of camber to the forward portion of the chord. Lift, drag, pitching-moment, and trailing-edge-flap hinge-moment characteristics of the modified wing are compared with results from the original wing.

Report presenting a comparison of the lift, drag, and pitching-moment characteristics of several wings with 35 degrees of sweepback and various amounts of camber in wind-tunnel testing. Six semispan model wings were tested, three with an aspect ratio of 10 and three with an aspect ratio of 5. Results regarding model distortion under aerodynamic loads, effects of Reynolds number, effects of Mach number, and effects of camber are provided.

Memorandum presenting an investigation of a 2:1 area-ratio diffuser of length equal to the inlet diameter with several arrangements of simple rectangular vortex generators over a speed range up to an inlet Mach number of 0.5. The investigation was for an inlet boundary layer of 5 percent of the inlet diameter, a condition for which this diffuser had substantial separated areas with no vortex generators. Results regarding the diffuser with no vortex generators, counterrotating vortex generators, other arrangements investigated, and a comparison with results from previous diffuser research are provided.

Memorandum presenting pressure distributions on two wing-body combinations obtained at a Mach number of 1.9 to investigate the wing-body interference. A rectangular wing, a triangular wing, and a cylindrical body with an ogive nose were studied alone and in combination. The pressure distributions over the wing-body combination compared favorably with theoretical calculations based primarily on a generalization of the method of Nielsen and Matteson, except at the root section of the wings where the boundary layer of the body modified the flow.

"This report summarizes the effects of fuel volatility and engine design variables on the problem of starting gas-turbine engines at sea-level and altitude conditions. The starting operation for engines with tubular combustors is considered as three steps; namely, (1) ignition of a fuel-air mixture in the combustor, (2) propagation of flame through cross-fire tubes to all combustors, and (3) acceleration of the engine from windmilling or starting speed to the operating speed range. Pertinent data from laboratory researches, single-combustor studies, and full-scale engine investigations are presented on each phase of the starting problem" (p. 1).

Report presenting a flight investigation of a ground-launched supersonic twin ram-jet test vehicle using short flame-length burners. Results were obtained for a range of Mach numbers, altitudes, and fuel-air-ratios. Engine performance, gross thrust, fuel rate, total impulse, values of combustion efficiency and impulse, and overall combustion efficiency are also included.

Memorandum presenting an investigation conducted in the Lewis 8- by 6-foot supersonic wind tunnel to determine the force and pressure characteristics of an all-external compression inlet with a conical spike and a supersonic cowl lip. Measurements of lift, drag, pitching moment, and internal and external pressures were made at free-stream Mach numbers of 1.59, 1.79, and 1.99 for a range of mass-flow ratios and angles of attack to 10 degrees.

Report presenting an investigation of 16-inch-diameter ram-jet units under free-flight conditions to determine performance at high subsonic, transonic, and supersonic velocities. Full-scale units were released from the airplane at high altitudes and accelerated by the engine thrust and force of gravity. Results regarding the diffuser total-pressure recovery, drag, thrust coefficient, and combustion are provided.

Report presenting an investigation in the supersonic tunnel at Mach number 1.85 and angles of attack from 0 to 5 degrees to determine optimum design configurations for a convergent-divergent type of supersonic diffusers with a subsonic diffuser of 5 degrees included divergence angle. Total-pressure recoveries in excess of the theoretical recovery across a normal shock at a free-stream Mach number of 1.85 were obtained with a number of configurations.

An investigation was made of the spray characteristics of a jet-powered dynamic model of the Bureau of Aeronautics DR 56 flying-boat design with a vee tail. A limited investigation was made to determine the effect of the change in tail design on the take-off and landing behavior in smooth water and in waves 8 feet high (full size).

Report presenting testing of a wing-body combination with a plane triangular wing of aspect ratio 2 and NACA 0003-63 sections in streamwise planes at subsonic and supersonic Mach numbers. Lift, drag, and pitching moment are presented for a range of Mach and Reynolds numbers.

Report presenting a wing-body combination with a plane triangular wing of aspect ratio 2 and NACA 0005-63 sections in streamwise planes has been investigated at subsonic and supersonic Mach numbers. Lift, drag, and pitching moment are presented for a range of Mach and Reynolds numbers.

Report presenting an investigation of a wing-body combination with a plane triangular wing of aspect ratio 2 and NACA 0008-63 sections in streamwise planes at subsonic and supersonic Mach numbers. Lift, drag, and pitching moment are presented for a range of Mach and Reynolds numbers.

Report presenting an investigation of a wing-body combination with a plane triangular wing of aspect ratio 4 and NACA 0005-63 sections in streamwise planes at subsonic and supersonic Mach numbers. Lift, drag, and pitching moment are presented for a range of Mach and Reynolds numbers.

Report presenting a wing-body combination with a plane triangular wing of aspect ratio 2 with NACA 0005-63 thickness distribution in streamwise planes, which has been twisted and cambered for a trapezoidal span load distribution at subsonic and supersonic Mach numbers.

A wing-body combination having a plane triangular wing of aspect ratio 2 with NACA 0005-63 thickness distribution in streamwise planes, and twisted and cambered for a trapezoidal span load distribution has been investigated at both subsonic and supersonic Mach numbers. The lift, drag, and pitching moment of the model are presented for Mach numbers from 0.60 to 0.90 and 1.30 to 1.70 at a Reynolds number of 3.0 million. The variations of the characteristics with Reynolds number are also shown for several Mach numbers.

"A wing-body combination having a triangular wing of aspect ratio 4 with NACA 0005-63 thickness distribution in streamwise planes, and cambered and twisted for a trapezoidal span distribution has been investigated at both subsonic and supersonic Mach numbers. The lift, drag, and pitching moment of the model are presented for Mach numbers from 0.25 to 0.96 and 1.20 to 1.70 at a Reynolds number of 1.5 million. The variations of the characteristics with Reynolds number are also shown for several Mach numbers" (p. 1).