The calculation of shielding the thickness for plutonium is complicated by the many different energies represented in the gamma radiation emitted during decay of the plutonium isotopes. Dose rate predictions are also frequently confused by gamma from varying content of fission product impurities in the plutonium, as well as other gamma radiation induced through alpha and neutron particle absorption within the source material or its environment. After assumptions are made for these many factors the radiation data for shielding determination is still frequently inadequate because of wide variations in dose rates resulting from self-absorption. The degree if self-shielding is in turn dependent on nature of the plutonium compound, degree of compactness, weight, and over-all geometrical distribution of the source material. By preparing a variety of plutonium samples representing combinations of these varying factors, actual dose rates and gamma spectra, as obtained from them, can then be extrapolated for application to specific situations.

Continued process improvements in the separation plants provide an incentive for economics in waste storage costs by utilizing existing facilities to their maximum capability consistent with the radiological hazards involved. The major improvements have reduced waste volumes resulting in increased fission product concentration and energy potential. Analyses have been made to determine the effect of this change on the integrity of the existing structures.

The NPR design calls for carbon steel to be the major constituent in the reactor coolant piping system. The piping and its associated fittings will, in all likelihood, be exposed to atmospheric weather conditions during the period of reactor construction. This type of exposure causes rusting. From experience gained during the startup of KER Loop 1 it is expected that there will be initially high NPR coolant activity levels. The high activity during the startup of KER Loop 1 was partially caused by the activation of rust that was eroded from pipe walls. Prevention of rusting on the carbon steel prior to its introduction into the coolant system would reduce the initial activity levels.

Soil chemistry studies have been carried on at Hanford for a number of years in support of the disposal of low and intermediate level liquid wastes to the ground. Equilibrium type experiments were carried out to investigate the mechanisms of the reactions of Sr, Cs, and rare earth ions with soils (1, 3, 4, 5). Experiments were also conducted with simulated and actual wastes in soil columns and an empirical method was developed for prediction of radionuclide breakthrough from ground disposal facilities into ground water on the basis of short, laboratory soil columns and equilibrium experiments (6,7). In this method it is assumed that the shape and position of the breakthrough curve is the same under laboratory conditions as in the larger scale field case. It is also assumed that the "column volume" or amount of soil effectively used for fission product sorption is that directly under a disposal facility without considering any spreading of waste solutions. These assumptions are known to be on the conservative side, but the degree of conservativeness is not known.

From abstract: "Steady temperatures and thermal stresses are determined for long hexagonal tubes having round holes for the case of uniform internal heat generation and a fluid-cooled inside surface. Thermal stresses are also determined for thick plates pierced by holes on an equilateral triangular pattern and for hexagonal tubes having a hexagonal hole with rounded inside corners. Stresses in the end regions of tubes are also investigated."

A study of metallurgical problems resulting from variation in grain boundaries, bonding layers, and inclusions in metals and alloys has become increasingly important over the past several years. To keep pace with and aid in these studies, several new techniques have been developed in emission and X-ray spectroscopy. In X-ray, areas as smalls as one square micron can be studied by making them targets for a focused electron beam and observing the X-rays emitted (5,2). Such an instrument would be quite helpful at Hanford, but the high original cost is prohibitive.

Samples containing 5 to 10 mg of uranium were extracted with hexone (methyl isobutyl ketone) and titrated coulometrically in sulphate media. Relative standard deviations of 0.45% for samples containing 5 mg and 0.56% for 10 mg were determined by precision studies.

The initial and long-term nuclear characteristics of two internally cooled heterogeneous, graphite-moderated, two-region, molten-salt reactors have been studied. These reactors have doubling times of 22.5 years and 27.5 years. Methods of decreasing the doubling times by removing the Pa233 from the core and be increasing the specific power of the reactor are described.

The major portion of transfers and inventory in the Chemical Processing Department are dependent on volume measurement. Good volume measurements are therefore essential to good SS material control. Considerable attention has been given to the volume problem especially on primary transfer points. Document HW-57888 discusses the biasing effect pf temperature on manometer oil. HW- 57866 given the procedure for vessel calibration. Other undocumented correspondence has discussed recent calibrations and certain aspects of temperature considerations in the volume determinations. However, there is a need to document for future reference the consideration given temperature and provide at the same time information which covers the temperature angle on all volume methods used in the Chemical Processing Department.

The fire involved approximately 30 liters of isopropyl alcohol as a result of the ignition of about 16-18 liters of isopropyl alcohol and a slurry of thoria and ammonium nitrate in a 20-liter glass carboy. This material was undergoing a volume reduction by boiling in a floor-type metal hood with Plexiglas sides and 3 sliding door on the front of ordinary glass. The alcohol vapor was vents directly into the hood (Fig1.)

A series of critical experiments with blocks of 2% U235-enriched UF4-C25H52 has been initiated at the ORNL Critical Experiments Facility. Thus far assemblies with H:U235 atomic ratios of 195 and 294 have been built in parallelepipedal and simulated cylindrical geometries, both reflected and unreflected. From the results the minimum critical masses for reflected spheres have been determined to be 16.3 and 8.5 kg of U235 for fuel mixtures with H:U235 atomic ratios of 195 and 294, respectively. The minimum critical masses for unreflected spheres of these two fuel mixtures are 24.3 and 12.7 kg of U235, respectively.

This is the final report on the progress, "A Wide-Range Neutron Detector and Monitoring Instrument," ARF 1118-6. This report covers activities from May 8, 1958 to May 8, 1959. This report describes the basic design principles of a proportional counter that has been constructed whose cathode diameter increases towards one end.

The solids in Purex lww were first observed during flowsheet tests for recovery of fission products from plant wastes. Since the nature of this solid was not apparent from the flowsheet composition of lww, some work was performed to characterize this material. Although this work has been conducted over a period of about one year, it has been subordinate to the main one of testing flowsheets for fission product recovery. The solids have been observed in each of about six samples of plant lww that have been studied, and the centrifuged volume of solids has been about four percent in each case.

The following report describes the investigations of the microwave solution and the Astron solution, to produce high current electron beams.

Report detailing various Bremsstrahlung theories since 1945. Citations for different theories are included.

Report discussing low and high acceleration flight mechanics for interplanetary missions, as well as the energy limitation for electric propulsion systems powered by a nuclear energy source. From abstract: "An optimization procedure for low acceleration systems is given which leads to a simple relationship between mission requirements, payload fraction, power plant specific power, and exhaust velocity."

The following report describes two methods of extrusion cladding of uranium fuel plates that were investigated and evaluated.

"A ring circuit is a succession or two-port networks and at least one three-port network, each feeding the next at one port and the last feeding the first so that the sequence closes on itself leaving at least one input port. The input admittance is derived in terms ef various matrices describing the circuit for one- and two-input port rings."

Abstract: "The oxidation resistance of thin sheets of iron-28 w/o chromium-2.67 to 10.0 w/o alloys, nominally 0.004, 0.006, 0.008, 0.012, and 0.016 in. thick, was determined by exposure in static air for 100 hr at 2100 and 2300 F. A minimum of 3.67 and 9.37 w/o aluminum was necessary to prevent excessive oxidation of 0.004-in.-thick sheet material at 2100 and 2300 F, respectively. Correspondingly, specimens of lower aluminum content and greater thickness withstood the oxidation attack. Oxidation of iron-chromium-aluminum alloys appeared to be related to the diffusion of aluminum to surfaces of the sheet to form an adherent protective layer of Al2O3."

A general program has been written to plot curves on the Oracle curve plotter. The supplement includes changes to slow down some of the loops and minimize the possibility of read-around errors and changes to handle special cases.

During the development of in-reactor corrosion experiments three types of bomb designs have been developed for following quantitatively the consumption of oxygen in a bomb which is fabricated from the particular metal under test. The bombs are designed so as to be rocked continuously during their in-reactor exposure, consequently agitating the uranium salt solution contained in the bomb and permitting gentle movement of the solution past metal specimens and other corroding surfaces. The oxygen pressure is produced within the bomb at the beginning of the run either by the withdrawal of gas from an oxygen tank or by the decomposition of hydrogen peroxide added just prior to closure. Temperature measurements are obtained by mans of thermocouples placed in a well within the bomb body or, in the latest design, there will also be thermocouples staked at several points on the outer wall of the bomb. The assembly is inserted in an experimental access hole in the reactor, brought up to a predetermined operating temperature by means of an electric furnace in close contact with the bomb, and allowed to remain for the desired amount of exposure to reactor radiation. Periodic measurements of temperature and pressure are made and the bomb …

The operation of the HRT mockup was on 0.042m UO2SO4, 0.024m H2SO4, and 0.005m CuSO4 at 280 C and 1400 psi pressure. with the O2 content at near 500 ppm. The pump showed bearing wear and high corrosion. The letdown heat exchanger was removed from the mockup and sectioned. The metallographic examination revealed corrosion. Results of corrosion runs on Ti, zircaloy-2, and stainless steel are given.

A qualitative theory for cake formation in ThO2 slurries is presented. The sphere formation which occurs in "Standard" slurry can be explained on the same basis. The irregular and unpredictable yield strength is easily fitted into the theory. On the basis of this theory, the writer has been led to the conclusion that only colloidally stable slurries, or slurries with crystallites or comminution-resistant particles which are large enough to overcome colloidal effects (probably larger than 0.1u) can be used with assurance in the ThO2 reactor system. This conclusion holds for 300 gm/kg slurries as well as for more concentrated mixtures.

In analyzing stresses, deflections, and forces in piping and certain structural systems, it is useful to have a set of equations giving the deflections at any point of a curved beam in terms of the various loads acting on the beam. This technical report presents the deflection equations for a curved circular-arc beam of variable length. The cases treated include in-plane and out-of-plane bending due to forces and moments applied to the end of the beam in three principal directions, and uniformly distributed loads applied along the beam in these three directions. Deflections were calculated by the strain energy method using Castigliano's theorem.