Abstract: "The oxidation resistance of thin sheets of iron-28 w/o chromium-2.67 to 10.0 w/o alloys, nominally 0.004, 0.006, 0.008, 0.012, and 0.016 in. thick, was determined by exposure in static air for 100 hr at 2100 and 2300 F. A minimum of 3.67 and 9.37 w/o aluminum was necessary to prevent excessive oxidation of 0.004-in.-thick sheet material at 2100 and 2300 F, respectively. Correspondingly, specimens of lower aluminum content and greater thickness withstood the oxidation attack. Oxidation of iron-chromium-aluminum alloys appeared to be related to the diffusion of aluminum to surfaces of the sheet to form an adherent protective layer of Al2O3."

"This is a bibliography of journal articles relating to beryllium oxide. Sources consulted include; Chemical Abstracts, 1951-1955; Physics Abstracts, 1951-1955; Industrial Arts Index, 1955-Jan, 1957; and the library card catalog. Starred articles are available in the library.

A prototype sampler for obtaining samples of high radioactive UO2SO4 solution for use in the HRT is presented. It was successfully operated in conjunction with a low pressure water system and a high pressure, high temperature UO2SO4 system.

In order to test the effect of chromate ion on the corrosion of Zircaloy-2, a 0.04 m uranyl sulfate solution (enriched) containing added acid, copper sulfate and 557 ppm of Cr (VI) was autoclaved with rocking at 280 degrees C for about eight days in the HB-5 facility of the LITR. The average corrosion rate established by the rate of consumption of oxygen was 9.9 mpy at a power density of 4.9 w/ml. It is indicated by comparison with a previous corrosion study under LITR radiation that the presence of Cr (VI) had no significant effect on the radiation corrosion of Zircaloy-2 by enriched uranyl sulfate solutions. However, the data are not conclusive and may be interpreted as showing a low corrosion rate for a limited period (i.e. a short term inhibition) followed by correspondingly rapid corrosion.

A general program has been written to plot curves on the Oracle curve plotter. The supplement includes changes to slow down some of the loops and minimize the possibility of read-around errors and changes to handle special cases.

A qualitative theory for cake formation in ThO2 slurries is presented. The sphere formation which occurs in "Standard" slurry can be explained on the same basis. The irregular and unpredictable yield strength is easily fitted into the theory. On the basis of this theory, the writer has been led to the conclusion that only colloidally stable slurries, or slurries with crystallites or comminution-resistant particles which are large enough to overcome colloidal effects (probably larger than 0.1u) can be used with assurance in the ThO2 reactor system. This conclusion holds for 300 gm/kg slurries as well as for more concentrated mixtures.

In analyzing stresses, deflections, and forces in piping and certain structural systems, it is useful to have a set of equations giving the deflections at any point of a curved beam in terms of the various loads acting on the beam. This technical report presents the deflection equations for a curved circular-arc beam of variable length. The cases treated include in-plane and out-of-plane bending due to forces and moments applied to the end of the beam in three principal directions, and uniformly distributed loads applied along the beam in these three directions. Deflections were calculated by the strain energy method using Castigliano's theorem.

The operation of the HRT mockup was on 0.042m UO2SO4, 0.024m H2SO4, and 0.005m CuSO4 at 280 C and 1400 psi pressure. with the O2 content at near 500 ppm. The pump showed bearing wear and high corrosion. The letdown heat exchanger was removed from the mockup and sectioned. The metallographic examination revealed corrosion. Results of corrosion runs on Ti, zircaloy-2, and stainless steel are given.

During the development of in-reactor corrosion experiments three types of bomb designs have been developed for following quantitatively the consumption of oxygen in a bomb which is fabricated from the particular metal under test. The bombs are designed so as to be rocked continuously during their in-reactor exposure, consequently agitating the uranium salt solution contained in the bomb and permitting gentle movement of the solution past metal specimens and other corroding surfaces. The oxygen pressure is produced within the bomb at the beginning of the run either by the withdrawal of gas from an oxygen tank or by the decomposition of hydrogen peroxide added just prior to closure. Temperature measurements are obtained by mans of thermocouples placed in a well within the bomb body or, in the latest design, there will also be thermocouples staked at several points on the outer wall of the bomb. The assembly is inserted in an experimental access hole in the reactor, brought up to a predetermined operating temperature by means of an electric furnace in close contact with the bomb, and allowed to remain for the desired amount of exposure to reactor radiation. Periodic measurements of temperature and pressure are made and the bomb …