This Record of Technical Change provides updates to the technical information included in the ``Fluid Management Plan for the Project Shoal Area Off-sites Project,'' April 1999

The relevance of rf-sheath-plasma interactions to ICRF operation in TFTR has been studied. Screen-screen and screen-limiter rf sheaths have been identified and analyzed for the old and new Bay M geometries on TFIR, including sheath voltages driven by both feeders and the central antenna conductor. Calculations have been carried out to determine the effects of ICRF on edge transport (profile flattening by E {times} B convection), impurity influx ({delta}Z{sub eff}) and edge electron heating (FS glow phenomena) as a function of edge plasma parameters, rf power and antenna phasing. It was found that many of the experimentally observed ICRF-edge plasma interactions on TFIR are consistent with the predictions of rf sheath theory.

The authors present direct measurements of the Z{sup 0}-lepton coupling asymmetries, A{sub e}, A{sub {mu}}, and A{sub {tau}}. It is based on a data sample selected from 170 k Z{sup 0} decays collected by the SLD detector. The Z`s are produced by collisions of polarized e{sup {minus}} with unpolarized e{sup +} bunches at SLC. The couplings are extracted from the measurement of the left-right forward-backward asymmetry for each lepton species. The preliminary results (using information from all leptonic data for A{sub e}) are: A{sub e} = 0.148 {+-} 0.016, A{sub {mu}} = 0.102 {+-} 0.033 and A{sub {tau}} = 0.190 {+-} 0.034.

This paper introduces new octant-range, composite-type Gauss and mid-point rule angular quadrature formulas for neutron and photon transport computations. A generalization to octant-range quadratures is also introduced in order to allow for discontinuities at material interfaces for two- and three-dimensional transport problems which can be modeled with 60-degree triangular or hexagonal mesh subdivisions in the x-y plane.

Compressed Natural Gas (CNG) has favorable characteristics as a vehicular fuel, in terms of fuel economy as well as emissions. Using CNG as a fuel in a series hybrid vehicle has the potential of resulting in very high fuel economy (between 26 and 30 km/liter, 60 to 70 mpg) and very low emissions (substantially lower than Federal Tier II or CARB ULEV). This paper uses a vehicle evaluation code and an optimizer to find a set of vehicle parameters that result in optimum vehicle fuel economy. The vehicle evaluation code used in this analysis estimates vehicle power performance, including engine efficiency and power, generator efficiency, energy storage device efficiency and state-of-charge, and motor and transmission efficiencies. Eight vehicle parameters are selected as free variables for the optimization. The optimum vehicle must also meet two perfect requirements: accelerate to 97 km/h in less than 10 s, and climb an infinitely long hill with a 6% slope at 97 km/h with a 272 kg (600 lb.) payload. The optimizer used in this work was originally developed in the magnetic fusion energy program, and has been used to optimize complex systems, such as magnetic and inertial fusion devices, neutron sources, and mil guns. …

The overall project objective is to demonstrate the high efficiency of the Adams Counter-Current shale oil recovery process. The efficiency will first be demonstrated on a small scale, in the current phase, after which the demonstration will be extended to the operation of a small pilot plant. Thus the immediate project objective is to obtain data on oil shale retorting operations in a small batch rotary kiln that will be representative of operations in the proposed continuous process pilot plant. Although an oil shale batch sample is sealed in the batch kiln from the start until the end of the run, the process conditions for the batch are the same as the conditions that an element of oil shale would encounter in a continuous process kiln. Similar chemical and physical conditions (heating, mixing, pyrolysis, oxidation) exist in both systems.The two most important data objectives in this phase of the project are to demonstrate (1) that the heat recovery projected for this project is reasonable and (2) that an oil shale kiln will run well and not plug up due to sticking and agglomeration. The following was completed this quarter. (1) Twelve pyrolysis runs were made on five different oil shales. …

The authors propose an all-scintillating fiber detector for the purpose of outer tracking for the SDC. The objectives of this tracking system are to: (1) provide a first level trigger for {vert_bar}{eta}{vert_bar} < 2.3 with sharp p{sub T} threshold with the ability to resolve individual beam crossings; (2) provide pattern recognition capability and momentum resolution which complements and extends the capabilities of the inner silicon tracking system; (3) provide three dimensional linkage with outer detection systems including the shower maximum detector, muon detectors, and calorimetry; (4) provide robust tracking and track-triggering at the highest luminosities expected at the SSC. The many attractive features of a fiber tracker include good position resolution, low occupancy, low mass in the active volume, and excellent resistance to radiation damage. An additional important feature, especially at the SSC, is the intrinsically prompt response time of a scintillating fiber. This property is exploited in the construction of a level 1 trigger sensitive to individual beam crossings.

The overall project objective is to demonstrate the high efficiency of the Adams Counter-Current shale oil recovery process. The efficiency will first be demonstrated on a small scale, in the current phase, after which the demonstration will be extended to the operation of a small pilot plant. Thus the immediate project objective is to obtain data on oil shale retorting operations in a small batch rotary kiln that will be representative of operations in the proposed continuous process pilot plant. Although an oil shale batch sample is sealed in the batch kiln from the start until the end of the run, the process conditions for the batch are the same as the conditions that an element of oil shale would encounter in a continuous process kiln. Similar chemical and physical conditions (heating, mixing, pyrolysis, oxidation) exist in both systems.The two most important data objectives in this phase of the project are to demonstrate (1) that the heat recovery projected for this project is reasonable and (2) that an oil shale kiln will run well and not plug up due to sticking and agglomeration. The following was completed this quarter. (1) Twelve pyrolysis runs were made on five different oil shales. …

This work combines focused ion beam sputtering and ultra-precision machining for microfabrication of metal alloys and polymers. Specifically, micro-end mills are made by Ga ion beam sputtering of a cylindrical tool shank. Using an ion energy of 20keV, the focused beam defines the tool cutting edges that have submicrometer radii of curvature. We demonstrate 25 {micro}m diameter micromilling tools having 2, 4 and 5 cutting edges. These tools fabricate fine channels, 26-28 microns wide, in 6061 aluminum, brass, and polymethyl methacrylate. Micro-tools are structurally robust and operate for more than 5 hours without fracture.

Light ion beams may be the best option for an Inertial Fusion Energy (IFE) driver from the standpoint of ei%ciency, standoff, rep-rate operation and cost. This approach uses high-energy-density pulsed power to efficiently accelerate ions in one or two stages at fields of 0.5 to 1.0 GV/m to produce a medium energy (30 MeV), high-current (1 MA) beam of light ions, such as lithium. Ion beams provide the ability for medium distance transport (4 m) of the ions to the target, and standofl of the driver from high- yield implosions. Rep-rate operation of' high current ion sources has ako been demonstrated for industrial applications and couId be applied to IFE. Although (hese factors make light ions the best Iong-teml pulsed- power approach to IFE, light-ion research is being suspended this year in favor of a Z-pinch-driven approach which has the best opport lnity to most-rapidly achieve the U.S. Department of Energy sponsor's goal of high-yield fusion. This paper will summarize the status and most recent results of the light-ion beam program at Sandia National Laboratories (SNL), and document the prospects of light ions for future IFE driver development.

Automatic control of fine coal cleaning circuits has traditionally been limited by the lack of sensors for on-line ash analysis. Although several nuclear-based analyzers are available, none have seen widespread acceptance. This is largely due to the fact that nuclear sensors are expensive and tend to be influenced by changes in seam type and pyrite content. Recently, researchers at VPI&SU have developed an optical sensor for phosphate analysis. The sensor uses image processing technology to analyze video images of phosphate ore. It is currently being used by PCS Phosphate for off-fine analysis of dry flotation concentrate. The primary advantages of optical sensors over nuclear sensors are that they are significantly cheaper, are not subject to measurement variations due to changes in high atomic number minerals, are inherently safer and require no special radiation permitting. The purpose of this work is to apply the knowledge gained in the development of an optical phosphate analyzer to the development of an on-fine ash analyzer for fine coal slurries. During the past quarter, installation of the video-based ash analyzer at the Middle Fork plant site was completed. A method of measuring and automatically adjusting for small variations in the sensor illumination scheme was developed …

Automatic control of fine coal cleaning circuits has traditionally been limited by the lack of sensors for on-line ash analysis. Although several nuclear-based analyzers are available, none have seen widespread acceptance. This is largely due to the fact that nuclear sensors are expensive and tend to be influenced by changes in seam type and pyrite content. Recently, researchers at VPI&SU have developed an optical sensor for phosphate analysis. The sensor uses image processing technology to analyze video images of phosphate ore. It is currently being used by PCS Phosphate for off-line analysis of dry flotation concentrate. The primary advantages of optical sensors over nuclear sensors are that they are significantly cheaper, are not subject to measurement variations due to changes in high atomic number minerals, are inherently safer and require no special radiation permitting. The purpose of this work is to apply the knowledge gained in the development of an optical phosphate analyzer to the development of an on-line ash analyzer for fine coal slurries. During the past quarter, an industrially-hardened version of the video-based ash analyzer was designed and constructed. All components are now in place at the Middle Fork plant site awaiting the installation of a sample line …

This report evaluates the closure activities at the 105-DR Large Sodium Fire Facility. The closure activities discussed include: the closure activities for the structures, equipment, soil, and gravel scrubber; decontamination methods; materials made available for recycling or reuse; and waste management. The evaluation compares these activities to the regulatory requirements and closure plan requirements. The report concludes that the areas identified in the closure plan can be clean closed.

A small grant was added to an ongoing Navy program to extend the scope of ongoing work by development of a new laser instrument. The instrument, MSCAT (Miniature Scattering and Transmissometry) uses small angle scattering to obtain the needed multi-parameter information for measurement of particle size distribution and number density. During the short course of the grant, the instrument was built and tested in a field experiment off the coast of North Carolina. Useful data were obtained, and these have been presented at the Fall Meeting of the American Geophysical Union in 1994.

A number of auto companies have announced plans to have fuel cell powered vehicles on the road by the year 2004. The low-temperature polymer electrolyte fuel cells to be used in these vehicles require high quality hydrogen. Without a hydrogen-refueling infrastructure, these vehicles need to convert the available hydrocarbon fuels into a hydrogen-rich gas on-board the vehicle. Earlier analysis has shown that fuel processors based on partial oxidation reforming are well suited to meet the size and weight targets and the other performance-related needs of on-board fuel processors for light-duty fuel cell vehicles (1).

Using a diamond-anvil cell (DAC) phase transformation and room temperature Equation of State (EOS) for some actinides and lanthanides were studied to multimegabar (megabar = 100 GPa) pressures. Experimental data are compared with the theoretically predicted crystal structural changes and the pressure-volume relationships. There is a general agreement between theory and experiment for the structural changes in the lighter actinides, however in detail there are some discrepancies still. A generalized trend for the phase transformations in the lanthanides can be seen, which again has broad agreement with theory. We conclude that an accurate and robust theoretical base for predicting the phase transformations in the f-electron metals can be developed by incorporating the DAC data.

A consortium (Los Alamos, Sandia, OR, Livermore) have been collaborating under the GONII project to generate a synthetic seismic data base. Two deliverables were a common code that would run on the various site machines, and the use of these codes to generate parts of the final data base. The data base consists of a large number of shots applied to two geographic models developed by another part of GONII, the salt model and the overthrust model,s which were supplied as large files containing propagation velocity on a 3-D grid. Los Alamos was supplied with the source code of a seismic propagation code written by the French Petroleum Institute. A decision was made to port a subset of the code to Fortran on a node. Part of this contract was spent verifying/debugging the Fortran on a node code; a port of the code was made to run on the Cray. A total of 846 shots were run on the CM5. It was found that files on the SDA are not safe from corruption and the model velocity file may change.

In this paper, we present a broad comparison of studies for a selected set of parameters for different nuclear reactor types including the next generation. This serves as an overview of key parameters which provide a semi-quantitative decision basis for selecting nuclear strategies. Out of a number of advanced reactor designs of the LWR type, gas cooled type, and FBR type, currently on the drawing board, the Advanced Light Water Reactors (ALWR) seem to have some edge over other types of the next generation of reactors for the near-term application. This is based on a number of attributes related to the benefit of the vast operating experience with LWRs coupled with an estimated low risk profile, economics of scale, degree of utilization of passive systems, simplification in the plant design and layout, modular fabrication and manufacturing. 32 refs., 1 fig., 3 tabs.

Comparative experiments using high energy (10 MeV) electrons and test reactor neutrons have been undertaken to understand the role that primary damage state has on hardening (embrittlement) induced by irradiation at 300 C. Electrons produce displacement damage primarily by low energy atomic recoils, while fast neutrons produce displacements from considerably higher energy recoils. Comparison of changes resulting from neutron irradiation, in which nascent point defect clusters can form in dense cascades, with electron irradiation, where cascade formation is minimized, can provide insight into the role that the in-cascade point defect clusters have on the mechanisms of embrittlement. Tensile property changes induced by 10 MeV electrons or test reactor neutron irradiations of unalloyed iron and an Fe-O.9 wt.% Cu-1.0 wt.% Mn alloy were examined in the damage range of 9.0 x 10{sup {minus}5} dpa to 1.5 x 10{sup {minus}2} dpa. The results show the ternary alloy experienced substantially greater embrittlement in both the electron and neutron irradiate samples relative to unalloyed iron. Despite their disparate nature of defect production similar embrittlement trends with increasing radiation damage were observed for electrons and neutrons in both the ternary and unalloyed iron.

The authors present a compact, robust, solid-state blue light (490 nm) source capable of greater than 5 mW of output in a TEM{sub 00} mode. This device is an optically pumped, vertical external-cavity surface-emitting laser (VECSEL) with an intracavity frequency doubling crystal.

At the Fernald Environmental Restoration Management Corporation (FERMCO), our product is a clean site. We measure productivity by our progress in taking down buildings and dispositioning hazardous waste. To those ends, Quality and Safety work together to ensure that productivity is gained in the safest way possible. The Plant 7 deconstruction is an example of how this teamwork has increased productivity at the site.

The authors present an outlook for possible discovery of supersymmetry with broken R-parity at Run II of the Tevatron. They first present a review of the literature and an update of the experimental bounds. In turn they then discuss the following processes: (1) resonant slepton production followed by R{sub P} decay, (a) via LQD{sup c} and (b) via LLE{sup c}; (2) how to distinguish resonant slepton production from Z{prime} or W{prime} production; (3) resonant slepton production followed by the decay to neutralino LSP, which decays via LQD{sup c}; (4) resonant stop production followed by the decay to a chargino, which cascades to the neutralino LSP; (5) gluino pair production followed by the cascade decay to charm squarks which decay directly via L{sub 1}Q{sub 2}D{sub 1}{sup c}; (6) squark pair production followed by the cascade decay to the neutralino LSP which decays via L{sub 1}Q{sub 2}D{sub 1}{sup c}; (7) MSSM pair production followed by the cascade decay to the LSP which decays (a) via LLE{sup c}, (b) via LQD{sup c}, and (c) via U{sup c}D{sup c}D{sup c}, respectively; and (8) top quark and top squark decays in spontaneous R{sub P}.

A surface-micromachined two-degree-of-freedom system that was driven by parallel-plate actuation at antiresonance was demonstrated. The system consisted of an absorbing mass connected by folded springs to a drive mass. The system demonstrated substantial motion amplification at antiresonance. The absorber mass amplitudes were 0.8-0.85 pm at atmospheric pressure while the drive mass amplitudes were below 0.1 pm. Larger absorber mass amplitudes were not possible because of spring softening in the drive mass springs. Simple theory of the dual-mass oscillator has indicated that the absorber mass may be insensitive to limited variations in strain and damping. This needs experimental verification. Resonant and antiresonant frequencies were measured and compared to the designed values. Resonant frequency measurements were difficult to compare to the design calculations because of time-varying spring softening terms that were caused by the drive configuration. Antiresonant frequency measurements were close to the design value of 5.1 kHz. The antiresonant frequency was not dependent on spring softening. The measured absorber mass displacement at antiresonance was compared to computer simulated results. The measured value was significantly greater, possibly due to neglecting fringe fields in the force expression used in the simulation.

The objective of this project is to develop a comprehensive, interdisciplinary, quantitative characterization of a fluvial-deltaic reservoir which will allow realistic interwell and reservoir-scale modeling to be used for improved oil-field development in similar reservoirs world wide. The geological and petrophysical properties of the Cretaceous Ferron Sandstone in east-central Utah will be quantitatively determined. Both new and existing data will be integrated into a 3-D representation of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for interwell to regional-scale reservoir simulation. Results could improve reservoir management through proper infill and extension drilling strategies, reduce economic risks, increase recovery from existing oil fields, and provide more reliable reserve calculations. Transfer of the project results to the petroleum industry will be an integral component of the project. The technical progress is divided into several sections corresponding to subtasks outlined in the Regional Stratigraphy Task and the Case Studies Task of the original proposal. The primary objective of the Regional Stratigraphy Task is to provide a more detailed interpretation of the stratigraphy of the Ferron Sandstone outcrop belt from Last Chance Creek to Ferron Creek. The morphological framework established from the case studies will be used to generate …