None

The ternary semiconductor GaAs{sub 1{minus}x}N{sub x} with 0 < x < 0.3 can be grown epitaxially on GaAs and has a very large bowing coefficient. The alloy bandgap can be reduced to about 1.0 eV with about a 3% nitrogen addition. In this work, the authors measured the internal spectral response and recombination lifetime of a number of alloys using the ultra-high frequency photoconductive decay (UHFPCD) method. The data shows that the photoconductive excitation spectra of the GaAs{sub 0.97}N{sub 0.03} alloy shows a gradual increase in response through the absorption edge near E{sub g}. This contrasts with most direct bandgap semiconductors that show a steep onset of photoresponse at E{sub g}. The recombination lifetimes frequently are much longer than expected from radiative recombination and often exceeded 1.0{mu}s. The data were analyzed in terms of a band model that includes large potential fluctuations in the conduction band due to the random distribution of nitrogen atoms in the alloy.

The purpose of this protocol is to assist US Department of Energy (DOE) sites in releasing concrete for reuse. Current regulations allow the sites to release surface-contaminated materials if their radioactivity falls below certain levels and to possibly release materials with volumetric contamination or higher levels of surface contamination on a case-by-case basis. In all cases, an ALARA (as low as reasonably achievable) analysis that evaluates the risks of releasing volumetrically contaminated concrete or concrete with higher levels of surface contamination is required as a basis for proposing and setting new release limits that allow for reuse of the concrete material. To evaluate the dose impacts of reusing radioactively contaminated material, the measured radiation levels (pCi/g or disintegrations per minute [dpm]/100 cm{sup 2}) must be converted to the estimated dose (mrem/yr) that would be received by affected individuals. The dose depends on the amounts and types of isotopes present and the time, distance, and method of exposure (e.g., inhalation or external exposure). For each disposition alternative, the protocol provides a systematic method to evaluate the impact of the dose on the affected individuals. The cost impacts of reusing concrete also need to be evaluated. They too depend on the disposition …

This screening addresses the critical characteristics for food industry type cans and containers used for handling and storage of special nuclear materials at the Plutonium Finishing Plant (PFP). HNF-5460, Revision 0 specified a minimum tin plate of 0.50 Ib./base box. Since the food pack cans currently used and that have been tested have a listed tin plate of 0.20 lbs. per base box, Revision 1 reduced the tin plate to {ge} 0.20 Ib./base box (i.e., No. 20 tinned commercial steel or heavier). This revision lists Critical Characteristics for two (2) large filtered containers, and associated shielding over-packs. These new containers are called ''Nuclear Material Containers'' (NMCs). They are supplied in various sizes, which can be nested, one inside another. The PFP will use NMCs with volumes up to 8-quarts as needed to over-pack largely bulged containers.

Transversely polarized {Lambda} production in hard scattering processes is discussed in terms of a leading twist T-odd fragmentation function which describes the fragmentation of an unpolarized quark into a transversely polarized {Lambda}. We focus on the properties of this function and its relevance for the RHIC and HERMES experiments.

None

This report presents an assessment of the efficiency and power density limitations of thermophotovoltaic (TPV) energy conversion systems for both ideal (radiative-limited) and practical (defect-limited) systems. Thermodynamics is integrated into the unique process physics of TPV conversion, and used to define the intrinsic tradeoff between power density and efficiency. The results of the analysis reveal that the selection of diode bandgap sets a limit on achievable efficiency well below the traditional Carnot level. In addition it is shown that filter performance dominates diode performance in any practical TPV system and determines the optimum bandgap for a given radiator temperature. It is demonstrated that for a given radiator temperature, lower bandgap diodes enable both higher efficiency and power density when spectral control limitations are included. The goal of this work is to provide a better understanding of the basic system limitations that will enable successful long-term development of TPV energy conversion technology.

The modification of the optical characteristics of a laser beam by a plasma is a key issue in laser-plasma coupling. it is critical to understand how this takes place, if we are ever to understand the interaction processes in the plasma corona as well as the coupling at super-high intensities--as when laser pulses approach Petawatt intensities. Interpreting and understanding parametric instabilities in laser-produced plasmas has been a problem of increasing complexity. Improvements in diagnostic capabilities in experimental studies, as well as refinements in the modeling (using different numerical techniques), are showing a complex scenario: strong interplay among instabilities, modification of the plasma conditions caused by the instabilities, and modification to the initial distribution of laser intensity inside the plasma. Of particular interest are stimulated Brillouin scattering (SBS) and stimulated Raman scattering (SRS), instabilities which have been studied extensively during the past 20 years, both theoretically and experimentally. Until now, most studies--mainly driven by requirements associated with inertial confinement fusion (ICF)--have concentrated on backscattering instabilities. The role of forward instabilities has not received much attention, despite having the potentials for strongly modifying the overall laser-plasma interaction region. The objective of this project is to study numerically the nonlinear enhancement of large-angle, …

The purpose of the Financial Analysis for Phase 1 Privatization for the Tank Farm Contractor is to provide a third-party quantitative and qualitative cost and schedule risk analysis of HNF-1946. The purpose of this Financial Analysis for Phase 1 Privatization for the Tank Farm Contractor (TFC) is to document the results of the risk-based financial analysis of HNF-1946, Programmatic Baseline Summary for Phase 1 Privatization f o r the Tank Farm Contractor (Diediker 2000). This analysis was performed to evaluate how well the proposed baseline meets the U. S. Department of Energy, Office of River Protection (ORP) Letter OO-MSO-009, ''Contract NO. DE-AC06-99RL14047--The US Department of Energy, Office of River Protection (ORP) Mission Planning Guidance for Fiscal Year (FY) 2002--Revision 1'' (Short 2000). The letter requires a confidence level in the baseline schedule that is consistent with the Phase 1A readiness-to-proceed (RTP) assessment conducted in fiscal year (FY) 1998. Because the success of the project depends not only on the budget but also on the schedule, this risk analysis addresses both components of the baseline.

The following topics related to the treatment of cuttings, cavings and spallings releases to the surface environment in the 1996 performance assessment for the Waste Isolation Pilot Plant (WIPP) are presented: (1) mathematical description of models. (2) uncertainty and sensitivity analysis results arising from subjective (i.e., epistemic) uncertainty for individual releases, (3) construction of complementary cumulative distribution functions (CCDFs) arising from stochastic (i.e., aleatory) uncertainty, and (4) uncertainty and sensitivity analysis results for CCDFs. The presented results indicate that direct releases due to cuttings, cavings and spallings do not constitute a serious threat to the effectiveness of the WIPP as a disposal facility for transuranic waste. Even when the effects of uncertain analysis inputs are taken into account, the CCDFs for cuttings, cavings and spallings releases fall substantially to the left of the boundary line specified in the US Environmental Protection Agency standard for the geologic disposal of radioactive waste (40 CFR 191, 40 CFR 194).

The authors have fabricated high-efficiency thin-film CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} (CIGS)-based photovoltaic devices from solution-based electroplated (EP) and auto-plated (AP) precursors. As-deposited precursors are Cu-rich CIGS. Compositions were adjusted to CuIn{sub 1{minus}x}Ga{sub x}Se{sub 2} with additional In and Ga by physical vapor deposition (PVD) to the EP and AP precursor films. Auger analysis and grazing incident X-ray diffraction (GIXRD) were performed on devices prepared from EP and AP precursor films. The authors have also analyzed and compared EP, AP, and an PVD CIGS device by deep-level transient spectroscopy (DLTS).

None

This invention generally relates to the remote removal of pelletized samples from cylindrical containment capsules. V-blocks are used to receive the samples and provide guidance to push out rods. Stainless steel liners fit into the v-channels on the v-blocks which permits them to be remotely removed and replaced or cleaned to prevent cross contamination between capsules and samples. A capsule holder securely holds the capsule while allowing manual up/down and in/out movement to align each sample hole with the v-blocks. Both end sections contain identical v-blocks; one that guides the drive out screw and rods or manual push out rods and the other to receive the samples as they are driven out of the capsule.

The Human Resources Staffing Plan quantified the equivalent staffing needs required for the Tank Farm Contractor (TFC) and its subcontractors to execute the readiness to proceed baseline between FY 2000-2008. The TFC staffing needs were assessed along with the staffings needs of Fluor Hanford and the privatization contractor. The plan then addressed the staffing needs and recruitment strategies required to execute the baseline.

This report documents the C version of the MCAPM (Monte Carlo All Particle Method) generator and collision physics library of subroutines. The Monte Carlo data generator (gen2000) reads cross sections and distributions that describe in-flight reactions from a binary library and creates an internal data library. The collision routines (bang2000) use this internal library to perform the physics of interaction of particles with the background material. Particles modeled with MCAPM-C are neutrons, charged particles (p, d, t, {sup 3}He, and {alpha}), and {gamma}'s. MCAPM-C is written in (nearly) standard C, and versions exist for Sun Solaris, Compaq Unix, IBM AIX, SGI Irix, and Linux. The library and its data files are installed on LC's Compass, TC, Forest, Blue, and Sky machines. This report describes the contents and format of the library, physics assumptions made, and the interface to the library's subroutines.

This report presents the results of particle size analyses and calorimetry testing performed on selected single-pull sludge samples collected from the Hanford K East Basin between December 1998 and June 1999. The samples were collected as isolated cores predominantly from areas that had not been previously sampled (e.g., North Loadout Pit, Dummy Elevator Pit, Tech View Pit), or from areas in which the sludge composition had been altered since the last sampling (e.g., Weasel Pit). Particle size analyses were performed by washing wet sludge samples through a series of four sieves with openings of 250, 500, 1410, and 4000 {micro}m. The loaded sieves were weighed before and after drying to obtain wet and dry particle size distributions. Knowledge of the particle size distribution is needed to design and predict the performance of the systems that will be used to retrieve, transport, and recover sludge. Also, sieving provides an opportunity to observe the components in the sludge. For example, during sieving of the sludge sample from the North Loadout Pit, significant quantities of organic ion exchange beads were observed. The uranium metal content and the particle size of the uranium metal in the K Basin sludge will largely determine the chemical …

This document replaces HNF-1751, Revision 1. It incorporates updates to reflect changes in programmatic direction associated with the vitrification plant contract and associated DOE-ORP guidance. In addition it includes planning associated with failed/used melter and sample handling and disposition work scope. The document also includes format modifications and section numbering update consistent with CH2M HILL Hanford Group, Inc. procedures.

None

This document replaces HNF-1517, Rev 2 which is deleted. It incorporates updates to reflect changes in programmatic direction associated with the vitrification plant contract change and associated DOE/ORP guidance. In addition it incorporates the cancellation of Project W-465, Grout Facility, and the associated modifications to Project W-520, Immobilized High-Level Waste Disposal Facility. It also includes document format changes and section number modifications consistent with CH2M HILL Hanford Group, Inc. procedures.

None

Laser deposits fabricated from two different compositions of 304L stainless steel powder were characterized to determine the nature of the solidification and solid state transformations. One of the goals of this work was to determine to what extent novel microstructure consisting of single-phase austenite could be achieved with the thermal conditions of the LENS [Laser Engineered Net Shape] process. Although ferrite-free deposits were not obtained, structures with very low ferrite content were achieved. It appeared that, with slight changes in alloy composition, this goal could be met via two different solidification and transformation mechanisms.

None

None

The Sustained Spheromak Physics Experiment (SSPX) will examine the confinement properties of spheromak plasmas sustained by DC helicity injection. Understanding the plasma-surface interactions is an important component of the experimental program since the spheromak plasma is in close contact with a stabilizing wall (flux conserver) and is maintained by a high-current discharge in the coaxial injector region. Peak electron temperatures in the range of 400 eV are expected, so the copper plasma facing surfaces in SSPX have been coated with tungsten to minimize sputtering and plasma contamination. Here the authors report on the characterization and conditioning of these surfaces used for the initial studies of spheromak formation in SSPX. The high-pressure plasma-sprayed tungsten facing the SSPX plasma was characterized in-situ using beta-backscattering and ex-situ using laboratory measurements on similarly prepared samples. Measurements indicate that water can be desorbed effectively through baking while hydrocarbon/oxide removal using glow discharge and shot conditioning is slow due to the coating's high porosity.