Melter feed preparation processes, incorporating a final wash of the precipitate slurry feed to Defense Waste Processing Facility (DWPF) and a partial substitution of the SRAT formic acid requirement with nitric acid, should not produce peak hydrogen generation rates during Cold Chemical Runs (CCR's) and radioactive operation greater than their current, respective hydrogen design bases of 0.024 lb/hr and 1.5 lb/hr. A single SRAT bench-scale process simulation for CCR-s produced a DWPF equivalent peak hydrogen generation rate of 0.004 lb/hr. During radioactive operation, the peak hydrogen generation rate will be dependent on the extent DWPF deviates from the nominal precipitate hydrolysis and melter feed preparation process operating parameters. Two actual radioactive sludges were treated according to the new flowsheets. The peak hydrogen evolution rates were equivalent to 0.038 and 0.20 lb/hr (DWPF scale) respectively. Compared to the formic acid -- HAN hydrolysis flowsheets, these peak rates were reduced by a factor of 2.5 and 3.4 for Tank 15 and Tank 11 sludges, respectively.

We present the results of a measurement to understand the effects of transverse misplacement of the [sup 137]Cs source tube inside the cast Pb plates of the SDC EMC calorimeter. The PMT current from a scintillator was measured as the [sup 137]Cs source was displaced by varying thicknesses of Pb, as well as varying thicknesses of air gap. At a nominal depth of 2 mm in Pb, we find a change in scintillator output of about 25%/mm, and about 10%/mm of air gap. The data are compared to a simple calculation. By taking the sum of the scintillators on top and below a source tube, we estimate a source tube displacement of [plus minus]450[mu] will cause an error in the PMT output by 1%.

This document recommends an interim dilution strategy for the low nitrite precipitate hydrolysis process. A minimum carbon dioxide purge rate of 27 scan during feeding and for 15 minutes after feeding and a maximum precipitate slurry feed rate of 36 gpm are recommended. These recommendations provide an interim dilution strategy that will provide for the start of cold chemical runs and until additional offgas data is collected from the PHEF (Precipitate Hydrolysis Experimental Facility).

The present DWPF flowsheet calls for the chemical treatment of waste sludge with 90 wt% formic acid prior to the addition of the Precipitate Hydrolysis Aqueous (PHA) product. An alternative processing methodology, denoted the ``Nitric Acid Flowsheet``, has been proposed. In the application of this flowsheet, nitric acid would be used to neutralize sludge base components (hydroxides and carbonates) prior to the addition of late wash PHA. The late wash PHA will contain sufficient quantities of formic acid to adequately complete necessary reduction-oxidation (REDOX) reactions.

The present DWPF flowsheet calls for the chemical treatment of waste sludge with 90 wt% formic acid prior to the addition of the Precipitate Hydrolysis Aqueous (PHA) product. An alternative processing methodology, denoted the ``Nitric Acid Flowsheet``, has been proposed. In the application of this flowsheet, nitric acid would be used to neutralize sludge base components (hydroxides and carbonates) prior to the addition of late wash PHA. The late wash PHA will contain sufficient quantities of formic acid to adequately complete necessary reduction-oxidation (REDOX) reactions. The use of this flowsheet may result in a change in the nominal concentrations of two of the major REDOX reaction participants: formate (HCOO{sup minus}) and nitrate (NO{sub 3}{sup minus}).

Space Nuclear Reactor Systems, especially those used for propulsion, often have expected operation run times much shorter than those for land-based nuclear power plants. This produces substantially different radionuclide inventories to be considered in the safety analyses of space nuclear systems. This presentation describes an analysis utilizing ORIGEN2 and DKPOWER to provide comparisons among representative land-based and space systems. These comparisons enable early, conceptual considerations of safety issues and features in the preliminary design phases of operational systems, test facilities, and operations by identifying differences between the requirements for space systems and the established practice for land-based power systems. Early indications are that separation distance is much more effective as a safety measure for space nuclear systems than for power reactors because greater decay of the radionuclide activity occurs during the time to transport the inventory a given distance. In addition, the inventories of long-lived actinides are very low for space reactor systems.

The present DWPF flowsheet calls for the chemical treatment of waste sludge with 90 wt% formic acid prior to the addition of the Precipitate Hydrolysis Aqueous (PHA) product. An alternative processing methodology, denoted the Nitric Acid Flowsheet'', has been proposed. In the application of this flowsheet, nitric acid would be used to neutralize sludge base components (hydroxides and carbonates) prior to the addition of late wash PHA. The late wash PHA will contain sufficient quantities of formic acid to adequately complete necessary reduction-oxidation (REDOX) reactions. The use of this flowsheet may result in a change in the nominal concentrations of two of the major REDOX reaction participants: formate (HCOO[sup minus]) and nitrate (NO[sub 3][sup minus]).

The present DWPF flowsheet calls for the chemical treatment of waste sludge with 90 wt% formic acid prior to the addition of the Precipitate Hydrolysis Aqueous (PHA) product. An alternative processing methodology, denoted the Nitric Acid Flowsheet'', has been proposed. In the application of this flowsheet, nitric acid would be used to neutralize sludge base components (hydroxides and carbonates) prior to the addition of late wash PHA. The late wash PHA will contain sufficient quantities of formic acid to adequately complete necessary reduction-oxidation (REDOX) reactions.

The present DWPF flowsheet calls for the chemical treatment of waste sludge with 90 wt % formic acid prior to the addition of the Precipitate Hydrolysis Aqueous (PHA) product. An alternative processing methodology, denoted the Nitric Acid Flowsheet'', has been proposed. in the application of this flowsheet, nitric acid would be used to neutralize sludge base components (hydroxides and carbonates) prior to the addition of late wash PHA. The late wash PHA will contain sufficient quantities of formic acid to adequately complete necessary reduction-oxidation (REDOX) reactions.

This document recommends an interim dilution strategy for the low nitrite precipitate hydrolysis process. A minimum carbon dioxide purge rate of 27 scan during feeding and for 15 minutes after feeding and a maximum precipitate slurry feed rate of 36 gpm are recommended. These recommendations provide an interim dilution strategy that will provide for the start of cold chemical runs and until additional offgas data is collected from the PHEF (Precipitate Hydrolysis Experimental Facility).

Melter feed preparation processes, incorporating a final wash of the precipitate slurry feed to Defense Waste Processing Facility (DWPF) and a partial substitution of the SRAT formic acid requirement with nitric acid, should not produce peak hydrogen generation rates during Cold Chemical Runs (CCR`s) and radioactive operation greater than their current, respective hydrogen design bases of 0.024 lb/hr and 1.5 lb/hr. A single SRAT bench-scale process simulation for CCR-s produced a DWPF equivalent peak hydrogen generation rate of 0.004 lb/hr. During radioactive operation, the peak hydrogen generation rate will be dependent on the extent DWPF deviates from the nominal precipitate hydrolysis and melter feed preparation process operating parameters. Two actual radioactive sludges were treated according to the new flowsheets. The peak hydrogen evolution rates were equivalent to 0.038 and 0.20 lb/hr (DWPF scale) respectively. Compared to the formic acid -- HAN hydrolysis flowsheets, these peak rates were reduced by a factor of 2.5 and 3.4 for Tank 15 and Tank 11 sludges, respectively.

The present DWPF flowsheet calls for the chemical treatment of waste sludge with 90 wt % formic acid prior to the addition of the Precipitate Hydrolysis Aqueous (PHA) product. An alternative processing methodology, denoted the ``Nitric Acid Flowsheet``, has been proposed. in the application of this flowsheet, nitric acid would be used to neutralize sludge base components (hydroxides and carbonates) prior to the addition of late wash PHA. The late wash PHA will contain sufficient quantities of formic acid to adequately complete necessary reduction-oxidation (REDOX) reactions.

Large eddy simulation, LES, has often been carried out for the idealized situation of a simple convective boundary layer. Studies of dual Doppler radar and aircraft data from the Phoenix II experiment indicate that the boundary layer of the Colorado High Plains is not a purely convective boundary layer and it is influenced by the mountains to the west. The purpose of this study is to investigate the atmospheric boundary layer on one particular day on the Colorado High Plains. This research applies a LES nested within larger grids, which contain realistic topography and can simulate the larger-scale circulations initiated by the presence of the mountain barrier. How and to what extent the atmospheric boundary layer of the Colorado High Plains is influenced by larger scale circulations and other phenomena associated with the mountain barrier to the west is investigated. The nested grid LES reproduces the characteristics of the atmosphere for the case study day reasonably well. The mountains influence the atmospheric boundary layer over the plains to the east in several ways. The mountains contribute to the vertical shear of the horizontal winds through the thermally-induced mountain-plains circulation. As a consequence of the wind shear, the boundary layer that …

A network of hf ionospheric sounders consisting of two transmitter and two receiver stations was deployed to detect the effects of acoustic waves generated by surface ground motion following an underground nuclear test (UGT) at the Nevada Test Site. The frequency of the transmissions were chosen so that the hf radio waves were totally reflected in the E layer of the ionosphere at an altitude of approximately 100 km. The transmissions were highly stable cw tones at two frequencies separated by 100 kHz so that two altitudes separated by approximately .5 km could be sensed. The network sampled four geographic locations in the ionosphere ranging from almost directly overhead of the UGT out to a horizontal range of 60 km. The ionospheric sounders detected disturbances on all the paths beginning at approximately 325 s after the UGT which persisted for up to 100 s. These disturbances will be described in detail in a later paper. Shortly after the UGT an extended series of ionospheric disturbances were detected which we ascribe to the arrival of acoustic shock waves at the E layer caused by the surface detonation of ordinance with effective yields of 450 kg of high explosive during an unrelated …

We present the results of a measurement to understand the effects of transverse misplacement of the {sup 137}Cs source tube inside the cast Pb plates of the SDC EMC calorimeter. The PMT current from a scintillator was measured as the {sup 137}Cs source was displaced by varying thicknesses of Pb, as well as varying thicknesses of air gap. At a nominal depth of 2 mm in Pb, we find a change in scintillator output of about 25%/mm, and about 10%/mm of air gap. The data are compared to a simple calculation. By taking the sum of the scintillators on top and below a source tube, we estimate a source tube displacement of {plus_minus}450{mu} will cause an error in the PMT output by 1%.

Conducting polymers (CPs) have attracted attention as potentially useful materials for electrochemical capacitors due to their high energy storage capacity and their comparatively low cost. During the course of this research the authors explored a number of poly(heteroaromatic) systems, in conjunction with several nonaqueous electrolytes, that could be used as active materials in electrochemical capacitors. They identified a new configuration for such capacitors based on p- and n-dopable polymers and prepared a number4r of such materials. A new electrolyte, TMATFMS, which facilitates n-doping in these polymers was also synthesized and tested. A patent disclosure on these discoveries has been filed with Mr. Ray Wilson of LANL.

Two radio frequency (RF) cavities are needed in the Positron Accumulator Ring (PAR) of the Advanced Photon Source. One is for the first harmonic frequency at 9.8 MHz, and the other is for the twelfth harmonic frequency at 118 MHz. This note reports on the design of the 118 MHz RF cavity. Computer models are used to find the mode frequencies, impedances, Q-factors, and field distributions in the cavity. The computer codes MAFIA, URMEL, and URMEL-T are useful tools which model and simulate the resonance characteristics of a cavity. These codes employ the finite difference method to solve Maxwell`s equations. MAFIA is a three-dimensional problem solver and uses square patches to approximate the inner surface of a cavity. URMEL and URMEL-T are two-dimensional problem solvers and use rectangular and triangular meshes, respectively. URMEL-T and MAFIA can handle problems with arbitrary dielectric materials located inside the boundary. The cavity employs a circularly cylindrical ceramic window to limit the vacuum to the beam pipe. The ceramic window used in the modeling will have a wall thickness of 0.9 cm. This wall thickness is not negligible in determining the resonant frequencies of the cavity. In the following, results of two- and three-dimensional modeling …