''PIC'' simulation tracks particles through electromagnetic fields calculated self-consistently from the charge and current densities of the particles themselves, external sources, and boundaries. Already used extensively in plasma physics, such simulations have become useful in the design of accelerators and their r.f. sources. 5 refs.

We report results of simulations of stimulated Brillouin backscatter in which we see the second spatial harmonic of the ion density fluctuation and compare with linear, fluid theory. We also describe examples of the competition between Raman and Brillouin backscatter. 21 refs., 3 figs.

This report describes public opinion concerning the proposed monitored retrievable storage facility to be located in the vicinity of Oak Ridge, Tennessee. The majority of individuals who did express an opinion opposed the facility due to transport/safety concerns and environmental/health concerns. (CBS)

The workshop contains presentations in the following areas: (1) reservoir engineering research; (2) field development; (3) vapor-dominated systems; (4) the Geysers thermal area; (5) well test analysis; (6) production engineering; (7) reservoir evaluation; (8) geochemistry and injection; (9) numerical simulation; and (10) reservoir physics. (ACR)

The great distances between penetrations to the SSC tunnel create difficulties in ventilating and air conditioning the tunnel. Major penetrations were assumed for these calculations to be 8000 meters apart (one per sector) into an 8 foot diameter tunnel. The result of this large length to diameter ratio is that one cannot heat or dehumidify only from one end of the sector. Increasing the tunnel diameter to 9 feet does not affect this study; the area actually available for air flow depends on the floor design and space taken up by magnets and other equipment. For the 8 foot diameter tunnel this air flow area is taken to be 50 ft/sup 2/, the full tunnel cross sectional area. The length of the tunnel results in the necessity for distributed heating and dehumidification in the tunnel. Equipment may provide sufficient heating during operations, but there are some uncertainties. Among these are rock thermal conductivity. There must be introduction of outside air and removal of tunnel air. Skidded air intake units sized for 1 mph of tunnel air flow, consuming about 100 kW each, can provide outside air during construction, when circulation of air is not possible, and during operation.

This report summarizes the information compiled in 1984 while assessing the environmental impact of radionuclides in aquatic releases from the Rancho Seco Nuclear Power Generating Station. Gamma-emitting radionuclides discharged since 1981 are found in many of the dietary components derived from the creeks receiving the effluent wastewater. Some soils and crops are found to contain radionuclides that originate from the contaminated water that was transferred to land during the irrigation season. /sup 134/Cs and /sup 137/Cs are the primary gamma-emitting radionuclides detected in the edible flesh of fish from the creeks. Concentrations in the flesh of fish decreased exponentially with distance from the plant. No significant differences in the /sup 137/Cs activity were found between male and female fish of equal size, but concentrations may vary in fish of different size, with the season and diet. 21% of the total /sup 137/Cs and /sup 134/Cs discharged between 1981 and 1984 is associated with the creek sediments to a distance of 27 km from the plant. Fractions of the missing inventory have been transferred to land during the irrigation season or to downstream regions more distant than 27 km from the plant. The radiocesium content of the sediments in 1984 decreased …

This paper reviews research in the United States and Japan on structural materials for high-field superconducting magnets. Superconducting magnets are used for magnetic fusion energy devices and for accelerators that are used in particle-physics research. The cryogenic structural materials that we review are used for magnet cases and support structures. We expect increased materials requirements in the future.

This report describes public opinion concerning the proposed monitored retrievable storage facility to be located in the vicinity of Oak Ridge, Tennessee. The majority of individuals who did express an opinion opposed the facility due to transport/safety concerns and environmental/health concerns. (CBS)

The betatron heating of the core is commonly agreed to be due to a undesired difference mode in the kickers. This could be due to tolerances and mistakes in the kickers or in the hydrids which ideally drive the kickers in the sum mode. The purpose of this note is to estimate the effect of the latter. The hydrids, by the nature of their construction, have systematic errors. These errors appear to be larger than the errors which come from construction tolerances.

Meager Creek is perhaps the most intensely explored geothermal system occurring in the Cascade and Garibaldi Volcanic Belts. This paper describes the results of new lithologic, petrographic, X-ray, isotopic, and geochemical investigations of core and cuttings from the Meager Creek wells. The data demonstrate that alteration related to the present geothermal system is superimposed on basement rocks which were metamorphosed and intruded by dioritic stocks prior to the onset of volcanism. The geothermal alteration developed mainly after emplacement of hypabyssal dikes associated with Meager Mountain volcanism and is characterized by mineral assemblages consisting primarily of sheet silicates, quartz, carbonate, hematite, iron oxides, pyrite, and minor epidote, potassium feldspar, actinolite and biotite. Permeabilities within the upper portions of the reservoir are low, reflecting filling of the fracture systems by carbonate. Petrographic observations suggest that sealing of the fractures accompanied hydrothermal brecciation and boiling of the fluids.

Thermal 15 was drilled in November, 1983, to a TD of 700 feet. A steam entry encountered at 490 feet was found to communicate with the high-permeability upflow zone of the Thermal Shallow Reservoir. A low-flow-rate, higher-pressure steam entry at 600 feet was not detected while drilling but was indicated during a subsequent spinner survey. The pressure, flowrate, and enthalpy of the five wells completed in the upflow zone, including the Thermal 4 blowout, were monitored and recorded over a four month period before, during and after Thermal 15 was drilled. It was found that the Thermal 4 blowout communicates with the upflow zone of the Thermal Shallow Reservoir, the Thermal 4 flowrate is controlled by the shallow reservoir pressure, and the high permeability of the upflow zone allows such strong interference effects that three of the four commercial production wells will maximize production from this reservoir. A simple model was developed which describes the pressure-production characteristics of the reservoir over the normal range of operating conditions.

The Hawaii Geothermal Project (HGP-A) well, located in the Kilauea volcano east rift zone, was drilled to a depth of 6450 feet in 1976. It is considered to be one of the hot-test producing geothermal wells in the world. This single well provides 52,800 pounds per hour of 371 F and 160 pounds per square inch-absolute (psia) steam to a 3-megawatt power plant, while the separated brine is discharged in percolating ponds. About 50,000 pounds per hour of 368 F and 155 psia brine is discharged. Geothermal energy development has increased steadily in Hawaii since the completion of HGP-A in 1976: (1) a 3 megawatt power plant at HGP-A was completed and has been operating since 1981; (2) Hawaiian Electric Company (HECO) has requested that their next increment in power production be from geothermal steam; (3) three development consortia are actively, or in the process of, drilling geothermal exploration wells on the Big Island; and (4) engineering work on the development of a 400 megawatt undersea cable for energy transmission is continuing, with exploratory discussions being initiated on other alternatives such as hydrogen. The purpose for establishing the Puna Geothermal Research Facility (PGRF) is multifold. PGRF provides a facility in …

In bringing you up to date on DOE's geothermal R and D programs, they are going to emphasize first those elements that may be of special interest to a reservoir engineering audience, because the activities in support of an improved understanding of hydrothermal reservoirs deserve attention. Reservoir definition, brine injection, and reservoir stimulation technologies are major elements of the Hydrothermal Research Program, and in total they account for nearly 50% of the fiscal year (FY) 1985 hydrothermal research budget. These elements fall into the essential R and D category; that is, while some basic technologies have been borrowed from the petroleum industry for geothermal service, they are often ill-suited to geothermal requirements, and cannot be used without significant technological innovations. Into this category fall the current reservoir technology, brine injection, and reservoir stimulation projects that are listed in Table 1. The reservoir technology projects include: (1) development of methods for characterizing and mapping reservoir parameters, processes, and spatial dimensions; (2) development of methods to predict and monitor reservoir changes from fluid extraction; (3) evaluation of existing methods and development of new methods for predicting the location and mapping faults and fractures in geothermal reservoirs; and (4) testing of new analysis …

Extensive study of the Cerro Prieto geothermal field has provided much geologic and thermodynamic data of its structurally-complex, liquid-dominated reservoir. Several of the studies investigated the resource characteristics of fluid and energy flow. An early report by Mercado (1975) showed that the heat source for the part of the reservoir under development, now called Cerro Prieto I (CPI), originated in the eastern part of the field. Subsequent studies confirmed the flow of hot water from the east. A summary of several experimental and numerical studies of fluid and energy transport in the field was given by Lippmann and Bodvarsson (1983). The hydrogeologic model of Halfman et al. (1982) shows hot-water flow from the east divided into a shallow (alpha) aquifer at about 120Om and a deeper (beta) aquifer at about 170Om depth. A cross section along an east-west direction shows a central upflow to the two aquifers and uncertain geology beyond the western border of the field near well M-9. It also shows a fault dividing the line of border wells at M-29 from the inner wells at M-25 to the east. The hydrogeology of the field was described by Sanchez and de la Pena (1981) as an alluvial unit …

A large body of field data from Larderello shows striking temporal correlations between decline of well flow-rate, produced gas/steam ratio, chloride concentration and produced vapor fraction. The latter is inferred from measured concentrations of non-condensible gases in samples of well fluid, using chemical phase equilibrium principles. Observed temporal changes in the vapor fractions can be interpreted in term of a ''multiple source'' model, as suggested by D'Amore and Truesdell (1979). This provides clues to the dynamics of reservoir depletion, and to the evaluation of well productivity and longevity.

The large Thermal Landslide overlies the initial area of geothermal development at The Geysers. The landslide is waterbearing while the underlying Franciscan formation bedrock units are essentially non-waterbearing except where affected by hydrothermal alteration. Perched ground water moving through the landslide is heated prior to discharge as spring flow.

The boundaries of reservoir fluid convection cells are discreet and intricate zones, commonly sealed or reduced in permeabilities, which are often quite readily identifiable in many hydrothermal systems. Cell boundaries in the Geysers Steam Field are more vague; however, they are gradually being revealed by cumulative and extensive wellbore data. A profound example of a type of boundary has been revealed by drilling in one area of the steam field. A proposed model utilizes a sericitic alteration scheme to establish cell self-sealing. Mineralogical, permeability, and temperature properties all coincide so as to allow formation of a boundary model. This reinforces previously held views that the reservoir cell rock and hydrothermal system are greatly out of equilibrium. Such similar phenomena are suggested from drilling experiences in other parts of the steam field. Considerably, more work is required to better define and comprehend the nature and location of reservoir cell boundaries within the Geysers Steam Field.

The Nesjavellir High Temperature Geothermal Field is located in the Northern part of the Hengill Geothermal Area, which has been estimated to be one of the largest geothermal areas in iceland. Drilling started at Nesjavellir some 20 years ago with five wells. In 1982 a renewed exploration phase began and five additional wells have been drilled during the last three years. The pressure distribution within the geothermal system is very inhomogeneous in both horizontal and vertical directions. Variations in temperature are also considerable. The highest pressure and temperature is found in the southwestern part of the investigated area and both pressure and temperature decreases towards northeast. There seem to be four different zones of pressure potential in the system, which require the existence of both horizontal and vertical barriers in the system. Some parts of the geothermal system are in two-phase condition whereas other parts are in single phase liquid condition. The chemical composition of the fluid seem to be relatively uniform and a common origin of the fluid is assumed. The transmissivity of wells is in the range (1,3-3,5) 10{sup -8} m{sup 3}/Pa {center_dot} s whereas the flowing enthalpy ranges from 1200-2100 kJ/kg. The thermal output of wells are …

One of the major concerns of electric utilities in installing geothermal power plants is not only the longevity of the steam supply, but also the potential for changes in thermodynamic properties of the resource that might reduce the conversion efficiency of the design plant equipment. Production was initiated at Los Azufres geothermal field with wellhead generators not only to obtain electric energy at a relatively early date, but also to acquire needed information about the resource so that plans for large central power plants could be finalized. Commercial electric energy production started at Los Azufres during the summer of 1982 with five 5-MWe wellhead turbine-generator units. The wells associated with these units had undergone extensive testing and have since been essentially in constant production. The Los Azufres geothermal reservoir is a complex structural and thermodynamic system, intersected by at least 4 major parallel faults and producing geothermal fluids from almost all water to all steam. The five wellhead generators are associated with wells of about 30%, 60%, and 100% steam fraction. A study to compile existing data on the chemical and reservoir conditions during the first two years of operation has been completed. Data have been compiled on mean values …

The FRACSL flow and transport code is under development as part of an effort to improve reservoir characterization techniques. The present version simulates a two-dimensional, isothermal reservoir composed of a global fracture network imbedded in a porous media. FRACSL simulates the hydraulic response of a reservoir to injection or backflow. The code simulates the movement of injected tracers within the reservoir by adding advective and random dispersive motions of discrete particles. FRACSL has been benchmarked against theoretical flow and transport responses in simple systems. It has been used to simulate a benchscale physical model and to correlate flow and dispersion data from the East Mesa Hydrothermal Injection Test Program. Correlation of East Mesa data has provided an estimate of an anisotropic hydraulic conductivity, a natural drift in the reservoir, and dispersivity.

An extensive study of the Thermal Shallow Reservoir at The Geysers was performed in 1982 to improve our understanding of the source and flow patterns of steam in the shallow anomaly and how they relate to the Thermal 4 blowout. This project included gathering and analyzing pressure transient, enthalpy, tracer and chemical data and developing a reservoir model that was consistent with this data. Following the pressure transient testing and analysis, a convection-plume with lateral-flow model was proposed. Subsequent analysis of enthalpy, tracer and chemical data corroborated this model. The high flowrate wells--Thermal 4, Thermal 10, Thermal 11 and Magma 1--produce from the high-pressure, high-permeability upflow zone. The source of this upflow is a limited fracture system connecting the shallow anomaly with the underlying main reservoir. The outlying low-pressure, low-permeability wells are supplied by lateral flow of steam from the central area. The pressure gradient from the core to the periphery is caused by condensation in the flanks.

There have been two major high-temperature geothermal field developments in Iceland in the last decade; Krafla in the north-east, and Svartsengi in the south-west. These and other geothermal developments have recently been reported by Palmason et al. The Krafla field will not be discussed here, but details about the field are available in Stefansson and the power plant in Eliasson et al. Several reservoir engineering studies of the Krafla field have been published. The Svartsengi field is one of several fields on the Reykjanes Peninsula in south-west Iceland. About 15 km west of Svartsengi, on the tip of the Peninsula, the Reykjanes field is now under development, primarily for seawater chemicals production. The recently drilled Eldvorp field is located in line between these two fields, about 5 km west of Svartsengi. There are also several fields to the east of Svartsengi, at 15-20 km distance. The Svartsengi, Eldvorp, and Reykjanes fields exist in the same tectonic-volcanic environment, and are surrounded by similar geohydrological conditions, as discussed by Georgsson; see also Gudmundsson et al. and Franzson. Optimum development of these and other fields on the Reykjanes Peninsula, requires an understanding of their depletion behavior with time; that is, how the reservoir …

This paper presents the combined approaches of reservoir geology and engineering to a geothermal field where geological characteristics are highly complex and heterogeneous.Especially,the concrete approaches are discussed for the case of geothermal reservoir performance studies with a developed numerical model, by showing example cases accompanied with reinjection of produced disposal hot water into underground in an object geothermal reservoir. This combined approach will be a great help in solving complicated problems encountered during the development of a geothermal field.

A break in electrical power generation from the Krafla geothermal plant was planned from beginning of May to early September 1984. Early in June most of the production wells were shutin and their pressure recovery monitored. A regular monitoring of the pressure buildup was carried out on a well to well basis until mid-August, when the wells were put back into production except for wells 12 and 16. They were used to monitor the pressure drawdown due to the start of production. This was abruptly brought to an end by a nearby volcanic eruption in early September. The pressure buildup in the two-phase geothermal reservoir at Krafla is described and the first results presented. The results are compared with parameters determined on the completion of the wells and with predictions from numerical simulations of the reservoir. Finally the status of the Krafla geothermal system is discussed with regard to the comparison.