The new heavy ion synchrotron facility proposed by GSI will have two superconducting magnet rings in the same tunnel, with rigidities of 300 T-m and 100 T-m. Fast ramp times are needed, which can cause significant problems for the magnets, particularly in the areas of ac loss and magnetic field distortion. The development of the low loss Rutherford cable that can be used is described, together with a novel insulation scheme designed to promote efficient cooling. Measurements of contact resistance in the cable are presented and the results of these measurements are used to predict the ac losses, in the magnets during fast ramp operation. For the high energy ring, a lm model dipole magnet was built, based on the RHIC dipole design. This magnet was tested under boiling liquid helium in a vertical cryostat. The quench current showed very little dependence on ramp rate. The ac losses, measured by an electrical method, were fitted to straight line plots of loss/cycle versus ramp rate, thereby separating the eddy current and hysteresis components. These results were compared with calculated values, using parameters which had previously been measured on short samples of cable. Reasonably good agreement between theory and experiment was found, …

During this reporting period, the debinding and off-gassing furnace was switched from a vacuum furnace to a conventional kiln to solve the HIP can expansion problem during high temperature off-gassing, which caused disc distortion. Two 6.5 inch discs were produced. Both looked acceptable and one was machined. It was found that the disc hub section was little bit thin and micro cracks were seen along the disc radial directions.

This paper contains three analytical solutions of transport problems which can be used to test ray-effect errors in the numerical solutions of the Boltzmann Transport Equation (BTE). We derived the first two solutions and the third was shown to us by M. Prasad. Since this paper is intended to be an internal LLNL report, no attempt was made to find the original derivations of the solutions in the literature in order to cite the authors for their work.

None

Time series analysis techniques are applied to wave-front sensor telemetry data from the Lick Adaptive Optics System. For 28 fully-illuminated subapertures, telemetry data of 4096 consecutive slope estimates for each subaperture are available. The primary problem is performance comparison of alternative wave-front sensing algorithms. Using direct comparison of data in open loop and closed-loop trials, we analyze algorithm performance in terms of gain, noise and residual power. We also explore the benefits of multi-input Wiener filtering and analyze the open-loop and closed-loop spatial correlations of the sensor measurements.

Skin detection is an important preliminary process in human motion analysis. It is commonly performed in three steps: transforming the pixel color to a non-RGB colorspace, dropping the illumination component of skin color, and classifying by modeling the skin color distribution. In this paper, we evaluate the effect of these three steps on the skin detection performance. The importance of this study is a new comprehensive colorspace and color modeling testing methodology that would allow for making the best choices for skin detection. Combinations of nine colorspaces, the presence of the absence of the illuminance component, and the two color modeling approaches are compared. The performance is measured by using a receiver operating characteristic (ROC) curve on a large dataset of 805 images with manual ground truth. The results reveal that (1) the absence of the illuminance component decreases performance, (2) skin color modeling has a greater impact than colorspace transformation, and (3) colorspace transformations can improve performance in certain instances. We found that the best performance was obtained by transforming the pixel color to the SCT, HSI, or CIELAB colorspaces, keeping the illuminance component, and modeling the color with the histogram approach.

A very long base line super neutrino beam facility is need to determine the neutrino mixing amplitudes and phase accurately, as well as the CP violation parameters. This is possible due to the long distance and wideband nature of the neutrino beam for the observation of several oscillations from one species of the neutrino to the other. BNL plans to upgrade the AGS proton beam from the current 0.14 MW to higher than 1.0 MW and beyond for such a neutrino facility which consists of three major subsystems. First is a 1.2 GeV superconducting linac to replace the booster as injector for the AGS, second is the performance upgrade for the AGS itself for the higher intensity and repetition rate, and finally is target and horn system for the neutrino production. The major contribution for the higher power is from the increase of the repetition rate of the AGS form 0.3 Hz to 2.5 Hz, with moderate increase from the intensity. The design consideration to achieve high intensity and low losses for the linac and the AGS will be reviewed. The target horn design for high power operation and easy maintenance will also be presented.

The next generation of high-energy petawatt (HEPW)-class lasers will utilize multilayer dielectric diffraction gratings for pulse compression, due to their high efficiency and high damage threshold for picosecond pulses. The peak power of HEPW lasers will be determined by the aperture and damage threshold of the final dielectric grating in the pulse compressor and final focusing optics. We have developed a short-pulse damage test station for accurate determination of the damage threshold of the optics used on future HEPW lasers. Our damage test station is based on a highly stable, high-beam-quality optical parametric chirped-pulse amplifier (OPCPA) operating at 1053 nm at a repetition rate of 10 Hz. We present the design of our OPCPA system pumped by a commercial Q-switched pump laser and the results of the full system characterization. Initial short-pulse damage experiments in the far field using our system have been performed.

This paper describes the development of a lightweight high performance pump-fed divert and attitude control system (DACS). Increased kinetic Kill Vehicles (KV) capabilities (higher .v and acceleration capability) will especially be needed for boost phase engagements where a lower mass KV DACS enables smaller overall interceptors. To increase KV performance while reducing the total DACS dry mass (<10 kg), requires a design approach that more closely emulates those found in large launch vehicles, where pump-fed propulsion enables high propellant-mass-fraction systems. Miniaturized reciprocating pumps, on a scale compatible with KV applications, offer the potential of a lightweight DACS with both high {Delta}v and acceleration capability, while still enabling the rapid pulsing of the divert thrusters needed in the end-game fly-in. Pumped propulsion uses lightweight low-pressure propellant tanks, as the main vehicle structure and eliminates the need for high-pressure gas bottles, reducing mass and increasing the relative propellant load. Prior work used hydrazine and demonstrated a propellant mass fraction >0.8 and a vehicle propulsion dry mass of {approx}3 kg. Our current approach uses the non-toxic propellants 90% hydrogen peroxide and kerosene. This approach enables faster development at lower costs due to the ease of handling. In operational systems these non-toxic propellants can …