From Summary: "The purpose of this test was to compare six well-known airfoils, the R.A.F 15, U.S.A. 5, U.S.A. 27, U.S.A. 35-B, Clark Y, and Gottingen 387, fitted to the Sperry Messenger model, at full scale Reynolds number as obtained in the variable density wind tunnel of the National Advisory Committee for Aeronautics; and to determine the scale effect on the model equipped with all the details of the actual airplane. The results show a large decrease in minimum drag coefficient upon increasing the Reynolds number from about one-twentieth scale to full scale. A comparison is made between the results of these tests and those obtained from tests made in this tunnel on airfoils alone."

From Summary: "An analysis of available theory on seaplane impact and a proposed modification thereto are presented. In previous methods the overall momentum of the float and virtual mass has been assumed to remain constant during the impact but the present analysis shows that this assumption is rigorously correct only when the resultant velocity of the float is normal to the keel."

"The problem of the skin-stringer combinations used as axially loaded panels or as covers for box beams is considered from the point of view of the practical stress analyst. By a simple substitution the problem is reduced to the problem of the single-stringer structure, which has been treated in NACA Report no. 608. The method of making this substitution is essentially empirical; in order to justify it, comparisons are shown between calculations and strain-gage tests of three beams tested by the author and of one compression panel and three beams tested and reported elsewhere" (p. 469).

An investigation of a large group of related airfoils was made in the NACA variable-density wind tunnel at a large value of the Reynolds number. The tests were made to provide data that may be directly employed for a rational choice of the most suitable airfoil section for a given application. The variation of the aerodynamic characteristics with variations in thickness and mean-line form were systematically studied. (author).

The cooling of a single-row radial air-cooled engine using several cowling arrangements has been studied in the NACA 20-foot wind tunnel. The results show the effect of the propeller and several cowling arrangements on cooling for various values of the indicated horsepower in the climb condition. A table giving comparative performance of the various cowling arrangements is presented. The dependence of temperature on indicated horsepower and pressure drop across the baffles is shown by charts. Other charts show the limiting indicated horsepower against the pressure drop across the engine and the heat dissipated at various values of the indicated horsepower.

"Factors are obtained from semiempirical equations for correcting engine-cylinder temperatures for variation in important engine and cooling conditions. The variation of engine temperatures with atmospheric temperature is treated in detail, and correction factors are obtained for various flight and test conditions, such as climb at constant indicated air speed, level flight, ground running, take-off, constant speed of cooling air, and constant mass flow of cooling air. Seven conventional air-cooled engine cylinders enclosed in jackets and cooled by a blower were tested to determine the effect of cooling-air temperature and carburetor-air temperature on cylinder temperatures" (p. 49).

"As part of a program to study the correlation between molecular structure and physical properties of high-density hydrocarbons, the net heats of combustion, melting points, boiling points, densities, and kinematic viscosities of some hydrocarbons in the 2-n-alkylbiphenyl, 1,1-diphenylalkane, diphenylalkane, 1,1-dicyclohexylalkane, and dicyclohexylalkane series are presented" (p. 55).

Empirical design curves are presented for the critical stress of thin-wall cylinders loaded in axial compression. These curves are plotted in terms of the nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75.

"In this report a formula for calculating the induced drag of multiplanes with end plates is derived. The frictional drag of the end plates are used, is sufficiently large to increase the efficiency of the wing. Curves showing the reduction of drag for monoplanes and biplanes are constructed; the influence of gap-chord ratio, aspect ratio, and height of end plate are determined for typical cases. The method of obtaining the reduction of drag for a multiplane is described" (p. 253).

The investigation described in this report was conducted for the purpose of comparing an oleo-rubber-disk and a rubber-cord landing gear, built for use on an F6C-4 airplane. The investigation consisted of drop tests under various loading conditions and flight tests on an F6C-4 airplane. In the drop tests the total work done on each gear and the work done on each of the shock-absorbing units were determined. For both drop tests and flight tests the maximum loads and accelerations were determined. The comparative results showed that the oleo gear was slightly superior in reducing the ordinary landing shocks, that it had a greater capacity for work, and that it was very superior in the reduction of the rebound. The results further showed that for drops comparable to very severe landings, the rubber-cord gear was potentially more effective as a shock-reducing mechanism. However, due to the construction of this chassis, which limited the maximum elongation of the cords, this gear was incapable of withstanding as severe tests as the oleo gear. The action of the oleo gear was greatly inferior to the action of an ideal gear. The maximum accelerations encountered during the flight tests for severe landings were 3.64g for …

"Flame speeds based on the outer edge of the shadow cast by the laminar Bunsen cone were determined as functions of composition for methane-air mixtures at initial mixture temperatures ranging from -132 degrees to 342 degrees c and for propane-air and ethylene-air mixtures at initial mixture temperatures ranging from -73 degrees to 344 degrees c. The data showed that maximum flame speed increased with temperature at an increasing rate. The percentage change in flame speed with change in initial temperature for the three fuels followed the decreasing order, methane, propane, and ethylene" (p. 105).

This report presents the results of an analytical study of the lateral controllability of an airplane in which both the static rolling and yawing moments supplied by the controls and the reactions due to the inherent stability of the airplane have been taken into account. The investigation was undertaken partly for the purpose of coordinating the results of a long series of wind-tunnel investigations with phenomena observed in flight tests; for this reason a hypothetical average airplane, embodying the essential characteristics of both wind-tunnel models and the full-size test airplanes, was assumed for the study.

The effects of mass distribution on lateral stability and control characteristics of an airplane have been determined by flight tests of a model in the NACA free-flight tunnel. In the investigation, the rolling and yawing moments of inertia were increased from normal values to values up to five times normal. For each moment-of-inertia condition, combinations of dihedral and vertical-tail area representing a variety of airplane configurations were tested. The results of the flight tests of the model were correlated with calculated stability and control characteristics and, in general, good agreement was obtained.

This report presents the results of full-scale tests made on a 10-foot 5-inch propeller on a geared J-5 engine and also on a similar 8-foot 11-inch propeller on a direct-drive J-5 engine. Each propeller was tested at two different pitch settings, and with a large and a small fuselage. The investigation was made in such a manner that the propeller-body interference factors were isolated, and it was found that, considering this interference only, the geared propellers had an appreciable advantage in propulsive efficiency, partially due to the larger diameter of the propellers with respect to the bodies, and partially because the geared propellers were located farther ahead of the engines and bodies.

This report presents the results of wind tunnel tests to determine the effect on the characteristics of a propeller of inclining the propeller axis at small angles to the relative wind. Tests were made of a full-scale propeller and fuselage combination at four angles of yaw (0 degree, +5 degrees, +10 degrees, +15 degrees), and of a model propeller, nacelle, and wing combination of five angles of pitch (-5 degrees, 0 degree, +5 degrees, +10 degrees and +15 degrees). The results of the full-scale tests of a propeller and fuselage, without a wing, show that the effect on the propeller performance is small. Similar results are shown by the model test data except that where the propeller is directly in front of the wing there is an appreciable decrease in effective thrust and propulsive efficiency with increase of angle of pitch.

This paper gives some quantitative measurements of wind tunnel turbulence and its effect on the air resistance of spheres and airship models, measurements made possible by the hot wire anemometer and associated apparatus in its original form was described in Technical Report no. 320 and some modifications are presented in an appendix to the present paper. One important result of the investigation is a curve by means of which measurements of the air resistance of spheres can be interpreted to give the turbulence quantitatively. Another is the definite proof that the discrepancies in the results on the N. P. L. Standard airship models are due mainly to differences in the turbulences of the wind tunnels in which the tests were made.

This report presents the results of an investigation conducted in the Langley free-flight tunnel to determine the effects of large artificial variations of several rotary lateral-stability derivatives on the dynamic lateral stability and control characteristics of a 45 degree sweptback-wing airplane model. Calculations of the period and damping of the lateral motions and of the response to roll and yaw disturbances were made for correlation with the experimental results. The calculated results were in qualitative agreement with the experimental results in predicting the general trends in flight characteristics produced by large changes in the stability derivatives, but in some cases the theory with the assumption of zero lag was not in good quantitative agreement with the experimental results.

Charts are presented that permit the estimation of F-3 and F-4 knock-limited performance ratings for certain ternary and quaternary fuel blends. Ratings for various ternary and quaternary blends estimated from these charts compare favorably with experimental F-3 and F-4 ratings. Because of the unusual behavior of some of the aromatic blends in the F-3 engine, the charts for aromatic-paraffinic blends are probably less accurate than the charts for purely paraffinic blends.

"The magnitudes of the yawing moments produced by various parts of an airplane during spins have previously been found to be of major importance in determining the nature of the spin. Discrepancies in resultant yawing moments determined from model and full-scale tests, however, have indicated the probable importance of scale effect on the model. In order to obtain data for a more detailed comparison between full-scale and model results, flight tests were made to determine the yawing moments contributed by various parts of an airplane in spins. The inertia moment was determined by the usual measurement of the spinning motion, and the aerodynamic yawing moments on the fuselage, fin, and rudder were determined by pressure-distribution measurements over these parts of the airplane" (p. 305).

"This report describes an investigation made in order to determine the effect of tip speed on the characteristics of a thin-bladed metal propeller. The propeller was mounted on a VE-7 airplane with a 180-HP E-2 engine, and tested in the 20-foot propeller research tunnel of the National Advisory Committee for Aeronautics. It was found that the effect of tip speed on the propulsive efficiency was negligible within the range of the tests, which was from 600 to 1,000 feet per second (about 0.5 to 0.9 the velocity of sound in air)" (p. 465).

From Summary: "Despite the development of relatively ice-free fuel-metering systems, the widespread use of alternate and heated-air intakes, and the use of alcohol for emergency de-icing, icing of aircraft-engine induction systems is a serious problem. Investigations have been made to study and to combat all phases of this icing problem. From these investigations, criterions for safe operation and for design of new induction systems have been established. The results were obtained from laboratory investigations of carburetor-supercharger combinations, wind-tunnel investigations of air scoops, multicylinder-engine studies, and flight investigations. Characteristics of three forms of ice, impact, throttling, and fuel evaporation were studied."

"The relationships between conditions of hot-working and properties at high temperatures and the influence of the hot-working on response to heat treatment were investigated for an alloy containing nominally 20 percent molybdenum, 2 percent tungsten, and 1 percent columbium. Commercially produced bar stock was solution-treated at 2,200 degrees F. to minimize prior-history effects and then rolled at temperatures of 2,200 degrees, 2,100 degrees, 2,000 degrees, 1,800 degrees, and 1,600 degrees F. Working was carried out at constant temperature and with incremental decreases in temperature simulating a falling temperature during hot-working" (p. 1).

"The wall interference on an airfoil of finite span in an open-throat rectangular section has been treated theoretically and the result is presented in a convenient formula. Numerical results are given in tables and diagrams" (p. 355).

"In the first part, the boundary conditions for an open wind tunnel (incompressible flow) are examined with special reference to the effects of the closed entrance and exit sections. In the second part, solutions are derived for four types of two-dimensional open tunnels, including one in which the pressures on the two free surfaces are not equal. In the third part, a general method is given for calculating the boundary effect in an open circular wind tunnel of finite jet length" (p. 509).