From Introduction: "The investigation reported herein was initiated to define further the effects on the aerodynamic characteristics and load distribution of a thin, sweptback wing of a low-pressure blowing system and also to provide information on which to base a more thorough study of a complete airplane configuration."

Experimental investigation of flow about a slender body of revolution (NACA RM-10 missile) aligned and inclined to a supersonic stream was conducted at Mach numbers from 1.49 to 1.98 at a Reynolds number of approximately 30,000,000. Boundary-layer measurements at zero angle of attack are correlated with subsonic formulations for predicting boundary-layer thickness and profile. Comparison of pressure coefficients predicted by theory with experimental values showed close agreement at zero angle of attack and angle of attack except over the aft leeward side of body. At angle of attack, pitot pressure measurements in plane of model base indicated a pair of symmetrically disposed vortices on leeward side of body.

From Introduction: "The purpose of this paper is to discuss and evaluate some of the input signals or control parameters which have been experimentally employed to operate turbojet inlet-control systems. These include the normal-shock position, the oblique-shock position, and the diffuser-exit Mach number. The discussion is based on results obtained at the NACA Lewis laboratory during control investigations of ram-jet engines (ref. 1 to 5) and during a study on the control of a supersonic inlet for the J34 turbojet engine (refs 6 and 7)."

Report discussing the aerodynamic loading characteristics of a 45 degree sweptback wing with leading-edge chord extensions, including the effects of a spoiler-slot-deflector aileron. The wing section loading, wing-panel loading, and chord-extension loading are described.

Memorandum presenting a turbojet engine with a two-stage turbine operated with pentaborane fuel continuously for 11.5 minutes at a simulated altitude of 55,000 feet at a flight Mach number of 0.8. The engine incorporated an NACA combustor designed specifically for use with pentaborane fuel. Results regarding oxide formation and deposition, engine operating point, effect of oxide deposits on component performance, effect of oxide deposition on overall performance, and some operational comments are provided.

From Summary: "The primary objectives of the investigation reported herein were to determine the effect of this new combuster design on boric oxide deposition on engine parts and to determine the effect of boric oxide on the performance of multistage turbine. Pentaborance fuel (approx. 130 lb) was used in the engine performance evaluation reported herein. The data presented herein show the engine component and over-all performance deterioration with operation on pentaborane fuel".

Report presenting an investigation of four axial-flow single-stage compressors with a hub-tip radius ratio of 0.5 with three objectives related to the ideal symmetrical-velocity-diagram design, the comparison of blade-element turning angle and loss data with cascade data, and the validity of the simplified radial-equilibrium equation. Results regarding the overall performance, blade-element performance, and radial equilibrium considerations are provided.

Report presenting an investigation of the influence of high-altitude supersonic flight on the operation and effectiveness of turbine-blade liquid-cooling systems for application in turbojet engines in guided missiles and in supersonic aircraft. The problems encountered in liquid-cooling systems were investigated with reference to several specific designs for alternate heat-rejection mediums.

Report presenting an investigation in the full-scale tunnel to determine the effects of the low-speed aerodynamic characteristics of blowing air over the trailing-edge flap of a large-scale wing-body-tail model. Results regarding half-span flaps and full-span flaps, pitching-moment and longitudinal trim characteristics, drag characteristics, lift-drag ratio, and lateral control are provided.

Report presenting a longitudinal stability and control investigation of a model of the Convair B-58 external store over a range of Mach numbers. Normal force, chord force, and static and dynamic stability derivatives are provided. Abrupt pitching disturbances were created by step-function movements of the canard surface.

Memorandum presenting a longitudinal stability and control investigation made over a range of Mach numbers of a scale model of the Convair B-58 external store. Normal force, chord force, and static and dynamic stability derivatives formed an important part of the results. Results regarding the hinge moments and longitudinal trim and force coefficients are also provided.

A limited exploratory investigation of the rate of coking of four JP-4 fuels in electrically heated metal tubes was conducted in order to provide design information for fuel prevaporizers for turbojet-engine combustors. The fuels tested included two production and two minimum-quality JP-4 type fuels. The heating tube was operated at fuel pressures of approximately 500, 400, and 50 pounds per square inch. The operating fuel temperature was varied between approximately 600 degrees and 1200 degrees F.

Memorandum presenting experimental flutter Mach numbers for several solid, thin, rectangular cantilever wings with uniform section properties, low aspect ratio, and high relative density estimated from the results of previous tests at zero angle of attack. The experimental values are considered estimates, rather than determinations, in the high subsonic speed range because in that range the amplitude criterion was necessarily arbitrary. Results regarding conservatism of standard analysis relative to the experiment, closeness of analytical and experimental results, and interpretation of the analytical and experimental uncertainties are provided.

Empirical methods of Ainley and Kochendorfer and Nettles were used to predict performances of nine turbine designs. Measured and predicted performances were compared. Appropriate values of blade-loss parameter were determined for the method of Kochendorfer and Nettles. The measured design-point efficiencies were lower than predicted by as much as 0.09 (Ainley and 0.07 (Kochendorfer and Nettles).

"The over-all component performance characteristics of the J71 Type IIA three-stage turbine were experimentally determined over a range of speed and over-all turbine total-pressure ratio at inlet-air conditions af 35 inches of mercury absolute and 700 deg. R. The results are compared with those obtained for the J71 Type IIF turbine, which was previously investigated, the two turbines being designed for the same engine application. Geometrically the two turbines were much alike, having the same variation of annular flow area and the same number of blades for corresponding stator and rotor rows" (p. 1).

Report presenting generalized solutions for the actuator disk in subsonic compressible flow and the compressible- and incompressible-flow phenomena are compared. Results regarding the ideal solutions of flow variables, effect of additional losses, and actuator disks in tandem are provided. Large differences in flow variables were observed across the actuator disk.

"An investigation was conducted at the NACA Lewis laboratory to determine whether simulated porous gas-turbine blades fabricated by the Eaton Manufacturing Company of Cleveland, Ohio would be satisfactory with respect to coolant flow for application in gas-turbine engines. These blades simulated porous turbine blades by forcing the cooling air onto the blade surface through a large number of chordwise openings or slits between laminations of sheet metal or wire. This type of surface has a finite number of openings, whereas a porous surface has an almost infinite number of smaller openings for the coolant flow" (p. 1).

Report presenting a description of the Ames 2- by 2-foot transonic wind tunnel, its uses in testing, and a preliminary evaluation of the wall interference in the tunnel.

"Tests were made of a 1/18-scale dynamically similar model of the Lockheed Constellation airplane to investigate its ditching characteristics and proper ditching technique. Scale-strength bottoms were used to reproduce probable damage to the fuselage. The model was landed in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and fuselage configurations were simulated" (p. 1).

"The frequency of blade temperature to exhaust gas temperature is presented for two locations in the blade and at several operating conditions. The frequency response was determined by Fourier analysis of transient data. Two analytical methods are presented, and results are compared with experimental data. Dynamic response of turbine-blade temperature to exhaust-gas temperature exhibited the form of an approximate first-order lag" (p. 1).

Report presenting the effects of deflecting full-span, constant-chord, leading-edge flaps with round or sharp leading edges on the lift, drag, and pitching-moment characteristics of a model of an interceptor-type aircraft at supersonic and subsonic speeds.

The engines, each with a compressor overall total-pressure ratio of 12 and a design inner-turbine-inlet temperature of 2500 degrees R, were investigated at static sea-level conditions to determine the effect on transient performance of varying the desitn pressure ratio divisions 2-6, 3-4, and 4-3 between the outer and inner compressors. The transient considered was an acceleration from 40 to 100 percent design thrust. When the outer compressor of each engine reached design speed, the inner compressors were overspeeding, the maximum being only 1.7 over design mechanical speed. Acceleration times for the three engines were equal.

Report presenting a wind-tunnel investigation to determine the effects of leading-edge extensions on the longitudinal characteristics of a wing-fuselage and wing-fuselage-tail combination with a wing of 40 degrees sweepback and NACA 64A thickness distribution.

Memorandum presenting an investigation of the effect of Mach number variation from 1.8 to 7.4 on boundary-layer transition on a slender fin-stabilized ogive-cylinder body in free flight at a constant length Reynolds number of 13.8 million. Results showed that increasing Mach number had a very favorable effect of increasing the extent of the laminar boundary layer for a given surface roughness. Results regarding Mach number and surface roughness, effects of pressure rise, and long laminar runs are provided.