Report presenting measurements of the longitudinal stability, lift, and drag characteristics of an airplane configuration with a 60 degree delta wing and a swept horizontal tail mounted near the wing plane extended at a range of Mach numbers using the rocket-model technique. Comparisons are made to data form a similar model with the tail mounted above the wing plane.

Report presenting an investigation in the transonic pressure tunnel to determine the aerodynamic loading characteristics of a 60 degree delta wing in the presence of a body with and without body indentation in accordance with the transonic-area-rule concept. Tests covered a range of angles of attack and Mach numbers. Results regarding force and moment coefficients and curves are provided.

Report presenting an evaluation of the sea-level static equilibrium performance of an early developmental two-spool turbojet engine and its components and a comparison with a hypothetical two-spool turbojet engine. Results regarding the equilibrium performance of the actual engine, including its compressor performance, turbine performance, component operation, and engine performance and a comparison of those categories with the hypothetical engine are provided.

Memorandum presenting a supersonic wind-tunnel investigation of the origin and distribution of store interference in the 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.61 in which separate forces on a store, a fuselage, a swept wing, and a swept-wing-fuselage combination were measured. The report presents data on a configuration which simulated a fighter-bomber airplane with a large and a small external store.

Memorandum presenting an experimental investigation of an internal-contraction, axially symmetric inlet with isentropic compression surfaces on both the cowl and centerbody conducted over a range of Mach numbers from 2.0 to 2.7 at angles of attack from 0 to 6 degrees. The study was made to determine the optimum bleed system, together with a method of controlling the inlet.

Memorandum presenting a design and experimental investigation of a single-stage supersonic turbine. The turbine was designed for a rotor entering relative Mach number of 2. Results regarding the overall turbine performance, outer-wall static-pressure variation, momentum-loss considerations, effect of rotor modifications, and supersonic starting are provided.

Report presenting an investigation in the high speed tunnel to determine the effects of several wing-mounted external-store configurations on the aerodynamic characteristics of a model of a swept wing-fuselage combination for a range of Mach numbers. Some of the configurations explored included inboard underwing installations and wing-tip installations. Results regarding lift-drag ratios, drag characteristics, lift-curve slope, and pitching-moment characteristics are provided.

Report presenting surveys of the flow of the asymmetric adjustable nozzle of the 6- by 6-foot supersonic wind tunnel, which were made to determine the uniformity of the air stream. Test techniques for minimizing the effects of stream irregularities and the results of force and pressure-distribution tests of a swept-wing model are presented to illustrate the effectiveness of these techniques.

Investigation conducted in the altitude wind tunnel to study the effect of Reynolds number on the performance of an axial-flow compressor. The compressor was operated as a part of a turbojet engine over a range of pressure altitudes and compressor-inlet Reynolds numbers. Results regarding compressor efficiency, air flow, and a comparison with axial-flow compressors of different design are provided.

Report presenting an investigation of the operation of two submerged-type inlets in a wind tunnel at subsonic and transonic speeds. The pressure recovery was relatively constant throughout the lower subsonic speed range. The ability of the divergent-walled inlet to operate with satisfactory pressure recovery at higher free-stream Mach numbers than was possible with the parallel-walled inlet is attributed to the difference in the boundary-layer characteristics of the two types of inlets.

Report discussing tests of an unshrouded axial-flow supersonic compressor rotor. Information about the pressure ratio, efficiency, and flow rate with and without inlet guide vanes is provided. The results are also compared to testing on the original shrouded rotor.

Memorandum presenting an investigation of the rolling effectiveness of a partial-span, perforated spoiler on a wing with 45 degrees of sweepback at Mach numbers from 0.25 to 0.96. The effects of the spoiler on the lift, drag, and pitching moment were also determined. Results regarding Reynolds number, Mach number, and predicted rate of roll are provided.

Report presenting a wind-tunnel investigation at low speeds to determine the lateral-control and hinge-moment characteristics of a 20-percent-chord, unsealed, partial-span outboard aileron equipped with an overhang, a paddle, or a spoiler balance on a tapered 51.3 degree sweptback semispan wing model with an aspect ratio of 3.05. The aileron effectiveness was not greatly affected by the overhang or paddle balance, but the spoiler balance increased the effectiveness obtained with the plain flap.

Report presenting an investigation of a sweptback wing in combination with a fuselage of a type considered suitable for long-range, high-speed airplanes in the 12-foot pressure wind tunnel. The investigations included tests of the wing alone, the wing-fuselage combination, and the effects of fences.

Memorandum presenting an investigation conducted with an NACA submerged inlet at Mach numbers from 1.17 to 1.99. Total-pressure ratio, mass-flow ratio, and static pressure distribution along the ramp and main body were obtained at angles of attack of 0 and 6 degrees for a side inlet location. The results showed that the maximum total-pressure ratio attainable with the submerged inlet decreased from 0.83 at a Mach number of 1.17 to 0.52 at a Mach number of 1.99.

From Summary: "A flight investigation was made of a supersonic twin-ram-jet test vehicle using short-flame-length burners. The test demonstrated a maximum acceleration of 3.6g and a maximum flight Mach number of 3.02. Data were obtained over a Mach number range from about 1.9 to 3.0, an altitude range from 1,800 to 40,900 feet, and a fuel-air-ratio range from 0.012 to 0.065."

Report presenting a supersonic wind-tunnel investigation of the origin and distribution of store interference in the 4- by 4-foot supersonic pressure tunnel at Mach number 1.61. Separate forces on a store, a swept wing, and a swept-wing-fuselage combination were measured. This report presents data on a configuration that simulated a fighter-bomber airplane with a large and a small external store.

Report gives an account of an investigation conducted to determine the feasibility of artificially thickening a turbulent boundary layer on a flat plate. A description is given of several methods used to thicken artificially the boundary layer. It is shown that it is possible to do substantial thickening and obtain a fully developed turbulent boundary layer, which is free from any distortions introduced by the thickening process, and, as such, is a suitable medium for fundamental research.

"The source of an appreciable pitching-moment difference between left and right hovering turns for a tandem helicopter is described. The difference in pitching moment results from the difference in rotational speed of the counter rotating rotors with respect to the air while the helicopter is turning" (p. 1).

From Summary: "It is demonstrated with the aid of similitude arguments that a model launched from a hypervelocity gun upstream through a special supersonic nozzle should experience aerodynamic heating and resulting thermal stresses like those encountered by a long-range ballistic missile entering the earth's atmosphere. This demonstration hinges on the requirements that model and missile be geometrically similar and made of the same material, and that they have the same flight speed and Reynolds number (based on conditions just outside the boundary layer) at corresponding points in their trajectories. The hypervelocity gun provides the model with the required initial speed, while the nozzle scales the atmosphere, in terms of density variation, to provide the model with speeds and Reynolds numbers over its entire trajectory."

A 4-stroke-cycle test engine was equipped with a glass cylinder and the air movements within it were studied while the engine was being motored. Different types of air flow were produced by using shrouded intake valves in various arrangements and by altering the shape of the intake-air passage in the cylinder head. The air movements were made visible by mixing feathers with the entering air, and high-speed motion pictures were taken of them so that the air currents might be studied in detail and their velocities measured. Motion pictures were also taken of gasoline sprays injected into the cylinder on the intake stroke. The photographs showed that: a wide variety of induced air movements could be created in the cylinder; the movements always persisted throughout the compression stroke; and the only type of movement that persisted until the end of the cycle was rotation about the cylinder axis.

Report presenting a wind-tunnel investigation of the low-speed aerodynamic characteristics of an airplane configuration designed to obtain high lift-drag ratios at hypersonic speeds. The power-off landing of this aircraft would be difficult due to the high sinking speeds inherent in the design. Results regarding the longitudinal characteristics, lateral characteristics, and landing considerations are provided.

Report presenting measurements in a wind tunnel of the subsonic static and dynamic-rotary stability derivatives of a model of an airplane designed to fly at high supersonic speeds and high altitudes. The effects of flaps and landing gear, speed brakes, and several model components are included in the results as well as the stability characteristics of the model.

"At subsonic speeds the pressure drag arising from the thickness of the body or wings is negligible so long as the shapes are sufficiently well streamlined to avoid flow separation. In that range there exists no possibility of either favorable or adverse interference on the pressure distributions themselves. If one body is so placed as to receive a drag from the pressure field of another then the second body is sure to receive a corresponding increment of thrust from the first" (p. 1).