Early results from actual laboratory operation of a more versatile magnet supply.

Quarterly progress report on a project to test the radiation effects on metallurgy.

From introduction: "This paper describes a sequence for analyzing the effects of ground water flow on waste transport in natural soils."

Report discussing an improvement program on lithium mass spectrometers.

Introduction: This is a final report on the evaluation of Kanigen electroless nickel plating for surfaces in contact with water and steam i a sodium heated AISI Type 316 stainless steel steam generator. The purpose of the coasting was to afford protection from stress corrosion cracking originating on the water-steam side of the unit. It has been concluded that the kanigen coating does not afford adequate protection for the services condition intended. This work was performed as part of the research and development program for the United States Atomic Energy Commission sodium Components Design Project.

Abstract: In the March-April 1962 shutdown of SM-1 Core II, the SM-28 element will be re-inserted in SM-1 Core II and an SM-1 Core I element will be removed. An SM-1 Core II europium absorber will be replaced by a Ag-Cd-In absorber, and surveillance specimens will be inserted above the core support structure. Analysis of these changes concludes that re-insertion of the SM-2B stationary element and insertion of surveillance specimens do not affect hazards potential previously defined for SM-1. Replacement of the europium absorber by the Ag-Cd-In absorber will have negligible effect on reactivity control worth of the rod. The absorber meat section is encapsulated to prevent exposure of silver alloy to the primary coolant; postulated release of silver due to a cladding defect, after 2 years irradiation in SM-1, would not cause a hazard such as to restrict access to the vapor container. Possibility of steam formation in the air gap between the absorber core and cladding, causing a cladding failure, is remote. Deformation of the absorber section sufficient to cause the rod to stick, would not impair the ability of the other rods to shut down the reactor safely.

Preface; Subsequent to the analysis in the body of this report metallurgical developments indicated that it would not be feasible to build the APPR-1 Core II with the increased boron loading specified herein. At the time of the issuance of this report the Core II boron loading is to be the same as that for Core I. At the time of procurement of the core in the fall, if metallurgical developments warrant, the increased boron loading will be employed. The loading discussed in the body of the report and the first three appendices is that designed to meet the specifications outlined in the introduction. Appendix IV discusses changes in the loading to account for the various methods of employing boron.

Abstract: The caustic permanganate-rinse decontamination treatment was investigated. Loop and metallurgical studies were performed to determine optimum operating conditions as well as the metallurgical effects of the treatment. A treatment with 10 percent sodium hydroxide and 5 percent potassium permanganate solution followed by a rinse with a 5 percent ammonium citrate, 2 percent citric acid and 1/2 percent Versene solution was chosen for the decontamination of a stainless steel steam generator. Decontamination factors of greater than 50 were obtained in loop tests using the above treatment. Corrosion and metallurgical results indicated a total penetration of less than 0.01 mil on annealed Type 304 stainless steel with no evidence of any deleterious effects.

Abstract: A study has been made of the radiochemical composition and the specific activity of insoluble corrosion products (crud) removed from the primary system of the APPR-1. This report presents the results of analysis of twelve crud samples collected during the interval from September 3, 1957 to December 1, 1957. The samples were radiochemically analyzed for long-lived gamma emitting nuclides only. Data are presented on the measured values of the specific activity of crud, the ratios of the nuclide specific activities, and the concentration of crud (crud level) in the circulating primary water. Also included in data, based on the analysis of a single sample, comparing the specific activity of the deposited and circulating corrosion products.

Effect of x irradiation in oxygen and in hydrogen on chromosome aberration frequency in tradescantia microspores.

Report describing a the design requirements of a proposed nuclear power plant for use on an ice cap.

Operation and maintenance procedures for 30 megawatt heat exchanger and steam generator for sodium cooled reactor system.

Report from Hanford Laboratories concerning "the design and construction of the 100-N Reactor and heat dissipation plant complete with the necessary auxiliaries" (p. 2). Details of its construction and the plant's systems and instrumentation are described as well as economic considerations.

This study was undertaken for the USAEC under Contract AT(04-3)-189, Project Agreement No. 6, to investigate desirable features of a sodium cooled, graphite moderated uranium fueled power reactor using the modular concept, and, based on this investigation, evaluate the economic potential of this reactor type.

From abstract: "This section, Part II, extends the comparison of two ceramic fuel systems to include the fuel cycle cost comparison in greater detail particularly with respect to fabrication and reprocessing unit costs."

An experimental program to evaluate the performance of FCR and EFCR fuel during transient operation is outlined, and the initial series of tests are described in some detail. Test results from five experiments in the TREAT reactor, using 1-in. OD SS-clad UO₂ fuel specimens, are compared with regard to fuel temperatures, mechanical integrity, and post-irradiation appearance. Incipient fuel pin failure limits for transients are identified with maximum fuel temperatures in the range of 7000 deg F. Multiple transient damage to the cladding is likely for transients above the melting point of the fuel.

From abstract: "Describes Heat Transfer Reactor Experiment No. 3, a solid-moderated nuclear power plant with a horizontal reactor."

Results of processing 47 metric tons of Brookhaven spent reactor fuel are summarized.

Review of previous work is presented in addition to the results of recent studies concerning loss of primary coolant when the system is cold and pressurized and the problem of supplying adequate cooling following the injection of light water.

This report describes the development of an ultrasonic instrument for resin level measurements in an ion exchange column.

Specifications including detail dimension, materials, fabrication steps, acceptance criteria, and final assembly steps for the swaged uranium dioxide, 19-rod cluster Plutonium Recycle Test Reactor fuel element.

Engineering study on underground construction of nuclear power reactors.

An effort to develop a control on the air velocity at the door opening of a fume hood.

Report presenting research and development activities in the field of radioactive wastes. This particular report is concerned with the fixation of radioactive residues when the failure of a pot liner destroyed the furnace.