From Summary: "A description of the test methods used at the National Bureau of Standards for determining the characteristics of aircraft compasses is given. The methods described are particularly applicable to compasses in which mineral oil is used as the damping liquid. Data on the viscosity and density of certain mineral oils used in United States Navy aircraft compasses are presented. Results of flight tests are presented."

Report presents the results of wind tunnel tests of pressure distribution measurements over one section each of six airfoils. Pressure distribution diagrams, as well as the integrated characteristics of the airfoils, are given for both a high and a low dynamic scale or, Reynolds number VL/V, for comparison with flight and other wind-tunnel tests, respectively. It is concluded that the scale effect is very important only at angles of attack near the burble.

From Introduction: "The difficulties experienced in cooling the exhaust-valve seats of the rear-row cylinders have been overcome to a considerable extent by improving the mixture distribution through application of the injection impeller (reference 1) and by augmenting the flow of cooling air to the critical baffles (reference 2). Flight tests of this airplane (reference 3) indicated that the temperatures of exhaust-valve seats on rear-row cylinders were markedly lowered by these modifications and that airplane range, altitude, and gross weight previously limited by these temperatures could be greatly increased."

Report presents an analysis of the factors that determine the periodic twist of a rotor blade under the action of the air forces on it. The results of the analysis show that the Fourier coefficients of the twist are linear expressions involving only the tip-speed ratio, the pitch setting, the inflow coefficient, the pitching-moment coefficient of the blade airfoil section, and the physical characteristics of the rotor blade and machine.

"Several electrically heated finned steel cylinders enclosed in jackets were cooled by air from a blower. The effect of the air conditions and fin dimensions on the average surface heat-transfer coefficient q and the power required to force the air around the cylinders were determined. Tests were conducted at air velocities between the fins from 10 to 130 miles per hour and at specific weights of the air varying from 0.046 to 0.074 pound per cubic foot. The fin dimensions of the cylinders covered a range in pitches from 0.057 to 0.25 inch average fin thicknesses from 0.035 to 0.04 inch, and fin widths from 0.67 to 1.22 inches" (p. 269).

Approximate shapes of nonlifting bodies having minimum pressure foredrag at high supersonic airspeeds are calculated. With the aid of Newton's law of resistance, the investigation is carried out for various combinations of the conditions of given body length, base diameter, surface area, and volume. In general, it is found that when body length is fixed, the body has a blunt nose; whereas, when the length is not fixed, the body has a sharp nose. The additional effect of curvature of the flow over the surface is investigated to determine its influence on the shapes for minimum drag. The effect is to increase the bluntness of the shapes in the region of the nose and the curvature in the region downstream of the nose. These shape modifications have, according to calculation, only a slight tendency to reduce drag. Several bodies of revolution of fineness ratios 3 and 5, including the calculated shapes of minimum drag for given length and base diameter and for given base diameter and surface area, were tested at Mach numbers from 2.73 to 6.28. A comparison of theoretical and experimental foredrag coefficients indicates that the calculated minimum-drag bodies are reasonable approximations to the correct shape.

"This report compares the experimental force and moment data obtained by pressure measurements on a wing of aspect ratio 8.02, 45 degree sweptback of the quarter-chord line, taper ratio of 0.45, and NACA 63(sub 1)A012 airfoil sections with the calculated loadings obtained by the standard methods proposed by Weissinger, Falkner, and Multopp, as well as by several variations of these methods" (p. 1175).

A chart is presented for the values of the coefficient in the formula for the critical compressive stress at which buckling may be expected to occur in outstanding flanges. These flanges are flat rectangular plates supported along the loaded edges, supported and elastically restrained along one unloaded edge, and free along the other unloaded edge. The mathematical derivations of the formulas required for construction of the chart are given.

This report presents performance results of air cooled and water-cooled engines. The results obtained were sufficiently promising to warrant further investigation with fuel injection and spark ignition, with the same arrangement of inlet ports and exhaust valves at the bottom of the cylinder and the exhaust gases discharged through two poppet valves in the cylinder head. The displacement of the engine was 118 cubic inches. Optimum performance was obtained with the inlet air directed into the cylinder at an angle of 20 degrees to the radial.

"Equations and design charts are given for predicting the downwash angles and the wake characteristics for power-off conditions behind plain and flapped wings of the types used in modern design practice. The downwash charts cover the cases of elliptical wings and wings of taper ratios 1, 2, 3, and 5, with aspect ratios of 6, 9, and 12, having flaps covering 0, 40, 70, and 100 percent of the span. Curves of the span load distributions for all these cases are included" (p. 1).

"High-speed motion pictures were taken of fuel sprays with the NACA spray-photographic apparatus to study the distribution of the liquid fuel from the instant of injection cut-off until about 0.05 second later. The fuel was injected into a glass-walled chamber in which the air density was varied from 1 to 13 times atmospheric air density (0.0765 to 0.99 pound per cubic foot) and in which the air was at room temperature. The air in the chamber was set in motion by means of a fan, and was directed counter to the spray at velocities up to 27 feet per second" (p. 163).

"The NACA injection impeller was developed to improve the mixture distribution of aircraft engines by discharging the fuel from a centrifugal supercharger impeller and thus to promote a thorough mixing of fuel and charge air. Experiments with a double-row radial aircraft engine indicated that for the normal range of engine power the NACA injection impeller provided marked improvement in mixture distribution over the standard spray-bar injection system used in the same engine. The mixture distribution at cruising conditions was excellent; at 1200, 1500, and 1700 brake horsepower, the differences between the fuel-air ratios of the richest and the leanest cylinders were reduced to approximately one-third their former values" (p. 217).

"An approximate method for determining the convective cooling requirement in the laminar boundary-layer region of a body of revolution in high-speed flight was developed and applied to an example body. The cooling requirement for the example body was determined as a function of Mach number, altitude, size, and a surface-temperature parameter. The maximum value of Mach number considered was 3.0 and the altitudes considered were those within the lower constant-temperature region of the atmosphere (40,000 to 120,000 ft.)" (p. 463).

"This investigation was conducted as a part of a general research on fuel-injection engines for aircraft. The purpose of the investigation was to determine the effects of fuel and cylinder gas densities with several characteristics of fuel sprays for oil engines. The start, growth, and cut-off of single fuel sprays produced by automatic injection valves were recorded on photographic film by means of special high-speed motion-picture apparatus" (p. 491).

An analysis has been made of available data on vee tail surfaces. Previously published theoretical studies of vee tails have been extended to include the control effectiveness and control forces in addition to the stability. Tests of two isolated tail surfaces with various amounts of dihedral provided a check of the theory. Methods for designing vee tails were also developed and are given in the present paper.

The primary purpose of this investigation was to obtain simultaneous data on the loads and stress experience in flight by the U. S. S. Los Angeles which could be used in rigid airship structure design. A secondary object of the investigation was to determine the turning and drag characteristics of the airship. The aerodynamic loading was obtained by measuring the pressure at 95 locations on the tail surfaces, 54 on the hull, and 5 on the passenger car. These measurements were made during a series of maneuvers consisting of turns and reversals in smooth air and during a cruise in rough air which was just short of squall proportions.

This study of gaseous explosive reaction has brought out a number of important fundamental characteristics of the explosive reaction indicating that the basal processes of the transformation are much simpler and corresponds more closely to the general laws and principles of ordinary transformations than is usually supposed. The report calls attention to the point that the rate of molecular transformation within the zone was found in all cases to be proportional to pressure, that the transformation within the zone is the result of binary impacts. This result is of unusual interest in the case of the reaction of heavy hydrocarbon fuels and the reaction mechanism proposed by the recent kinetic theory of chain reactions.

Results are presented of an experimental and theoretical investigation of the growth of transverse velocity disturbances in the shear region caused by a flame in a duct. In the theoretical stability analysis, a flow field arising from a flame in a duct was analyzed. The flow was neutrally stable to symmetric disturbances and unstable to antisymmetric ones. In the experimental part of the program disturbances of various frequencies were imposed on a flame stabilized in a duct, and the effects were measured by shadow photography and photomultiplier-probe surveys.

Report presents the results of an investigation to determine the equilibrium temperature and heat-transfer coefficients for transverse cylinders in a high-speed stream of rarefied gas measured over a range of Knudsen numbers (ratio of molecular-mean-free path to cylinder diameter) from 0.025 to 11.8 and for Mach numbers from 2.0 to 3.3. The range of free-stream Reynolds numbers was from 0.28 to 203. The models tested were 0.0010-, 0.0050-, 0.030-, 0.051-, 0.080-, and 0.126-inch -diameter cylinders held normal to the stream.

Report presents the results of a study of combustion in a spark-ignition engine given in NACA Technical Reports 704 and 727. The present investigation was made with the NACA high-speed motion-picture camera, operating at 40,000 photographs a second, and with a cathode-ray oscillograph operating on a piezoelectric pick-up in the combustion chamber. Photographs are presented showing that the origin of knock is not necessarily in the end gas. The data obtained indicates that knock takes place only in a part of the cylinder charge which has been previously ignited either by autoignition or by the passage of the flame fronts but which has not burned to completion. Mottled regions in the high-speed Schlieren photographs are demonstrated to represent combustion regions.

"An investigation of the nature of the flow field behind a rectangular wing of circular arc cross section has been conducted in the Langley 9-inch supersonic tunnel. Pitot- and static-pressure surveys covering a region of flow behind the wing have been made together with detailed pitot surveys throughout the region of the wake. In addition, the flow direction has been measured by means of a weathercocking vane. Theoretical calculations have been made to obtain the variation of both downwash and sidewash with angle of attack by using the superposition method of Lagerstrom, Graham, and Grosslight" (p. 1).

An analysis is presented of the relationship of various engine factors to knock in preignition in an aircraft engine. From this analysis and from the available experimental data, a method of evaluating the knocking characteristics of the fuel in an aircraft-engine cylinder is suggested.

A method is presented for calculating the loading on a finite wing oscillating in subsonic or sonic flow. The method is applicable to any plan form and may be used for determining the loading on deformed wings. The procedure is approximate and requires numerical integration over the wing surface.

This report describes and develops methods by which the aerodynamic characteristics of an airfoil may be calculated with sufficient accuracy for use in airplane design. These methods for prediction are based on the present aerodynamic theory and on empirical formulas derived from data obtained in the N. A. C. A. variable density wind tunnel at a Reynolds number corresponding approximately to full scale. (author).