Memorandum presenting a flight investigation in natural icing conditions to determine the effect of ice formations on the performance of an axial-flow turbojet engine. Tail-pipe temperature increased from 761 to 1065 degrees Fahrenheit and the jet thrust decreased from 1234 to 910 pounds during a period of 45 minutes in icing. No general conclusions can be reached from the data because the icing condition was relatively light.

Report presenting a flight investigation in natural icing conditions to determine the effect of ice formations on the performance of an axial-flow turbojet engine. Results regarding the tail-pipe temperature, engine jet thrust, and characteristics of ice formation are provided. No general conclusions can be reached from the data because the icing condition was relatively light.

Compressor operation at low air flows for a given speed is limited by unstable flow conditions, commonly called surge. An investigation of surge in centrifugal compressors (reference 1) showed that the pulsation of pressures and velocities occurred when the slope of the compressor characteristic curve was positive and that the magnitude and frequency, as well as the incidence of surge, depended on the capacity and resistance of the total system. Although the theory presented in reference 1 is applicable to axial-floe compressors, little experimental information is available on the surge characteristics of the individual stages of axial-flow compressors, or on the variation of the surge characteristics with operating conditions.

Report presenting testing of six flutter wings, two swept 45 degrees and four unswept, attached to three freely falling bodies. Flutter frequency and phasing were recorded.

Report presenting an investigation of a model of the Kingfisher XAUM-2 flying torpedo to determine the pressure recoveries within the jet engine nacelle and to determine the effects of several changes in model configuration on the aerodynamic characteristics of the model. The effectiveness of elevons and tabs as control devices was also investigated.

Report presenting an investigation of two sharp-edge annular inlets with conical central bodies at low airspeeds in the propeller research tunnel to obtain information concerning the surface-pressure, drag, and pressure-recovery characteristics of the inlets at subsonic flight. Results regarding the nose and inner surface of the diffuser, inlet lips, minimum surface pressures and critical Mach numbers, pressure surveys in inlets, and pressure surveys in diffusers are provided.

"At the request of the Air Material Command, Army Air Forces, an investigation was conducted by the NACA Cleveland laboratory to determine the performance characteristics of the compressor of the XJ-41-V turbojet engine. This report is the second in a series presenting the compressor performance and analysis of flow conditions in the compressor. The static-pressure variation in the direction of flow through the compressor and the location and the cause of the maximum flow restriction at an equivalent speed of 8000 rpm are presented" (p. 1).

"An altitude-test-chamber investigation was conducted to determine the operational characteristics and altitude blow-out limits of a Solar afterburner in a 24C engine. At rated engine speed and maximum permissible turbine-discharge temperature, the altitude limit as determined by combustion blow-out occurred as a band of unstable operation of about 8000 feet altitude in width with maximum altitude limits from 32,000 feet at a Mach number of 0.3 to about 42,000 feet at a Mach number of 1.0. The maximum fuel-air ratio of the afterburner, as limited by maximum permissible turbine-discharge gas temperatures at rated engine speed, varied between 0.0295 and 0.0380 over a range of flight Mach numbers from 0.25 to 1.0 and at altitudes of 20,000 and 30,000 feet" (p. 1).

"Three modifications of the auxiliary-stage supercharger for the V-1710-93 engine were designed and tested as part of an investigation to improve the power output and the altitude performance of the engine. A 12-vane diffuser was substituted for the standard 11-vane diffuser, and a vaneless discharge passage and a modified scroll were designed to increase the flow capacity of the supercharger and thereby to increase the performance at the high volume flows required by the engine. With the 12-vane diffuser installed and the carburetor replaced by an adapter, the equivalent volume flow at the peak efficiency point was increased 25 percent at the lowest speed investigated and 9.5 percent at the highest speed" (p. 1).

From Introduction: "A 12-percent-chord-thick wedge section and a reversed NACA 0012 section were chosen for these tests as they are representative of sections having no boat tailing and appreciable boat tailing (i.e., blunt and rounded trailing edges, respectively), and the results of this investigation are compared with those obtained from a previous investigation of the NACA 0012 section. Conclusions are drawn regarding the relative merits of the two unconventional sections and the conventional section in transonic speed range."

From Summary: "An investigation was conducted in the Cleveland altitude wind tunnel to determine the operational characteristics of an axial flow-type turbojet engine with a 4000-pound-thrust rating over a range of pressure altitudes from 5,000 to 50,000 feet, ram pressure ratios from 1.00 to 1.86, and temperatures from 60 deg to -50 deg F. The low-flow (standard) compressor with which the engine was originally equipped was replaced by a high-flow compressor for part of the investigation. The effects of altitude and airspeed on such operating characteristics as operating range, stability of combustion, acceleration, starting, operation of fuel-control systems, and bearing cooling were investigated."

"An investigation to determine the performance and operational characteristics of an axial-flow gas turbine-propeller engine was conducted in the Cleveland altitude wind tunnel. As part of this investigation, the combustion-chamber performance was determined at pressure altitudes from 5000 to 35,000 feet, compressor-inlet ram-pressure ratios of 1.00 and 1.09, and engine speeds from 8000 to 13,000 rpm. Combustion-chamber performance is presented as a function of corrected engine speed and corrected horsepower" (p. 1).

"A fuel-distribution control for continuous-flow manifold injection on reciprocating engines is described. A method is installation of the control on an engine is suggested. The device controlled the flow to four spring-loaded nozzles within 2 percent of perfect distribution over a wide range of fuel-flow rates and the distribution was practically unaffected by uneven discharge-nozzle pressures" (p. 1).

"The inlet guide vanes for the supersonic compressor of the XJ55-FF-1 engine were studied as a separate component in order to determine the performance prior to installation in the compressor test rig. Turning angles approached design values, and increased approximately to through the inlet Mach number range from 0.30 to choke. A sharp break in turning angle was experienced when the choke condition was reached" (p. 1).

"An investigation is being conducted to determine the altitude performance characteristics of the Nene II engine and its components. The present paper presents the preliminary results obtained using jet nozzle 18.00 inches in diameter, with an area equal to 92.2 percent of the area of the standard jet nozzle for this engine. The experimental results presented are for conditions simulating altitudes from 20,000 to 60,000 feet and ram-pressure ratios from 1.1 to 3.5" (p. 1).

"Pressure-distribution data of the NACA 64(sub 1)-012 and 64(sub 1)A012 airfoils have been analyzed to determine the effects of increasing the trailing-edge angle from 9 to 14 degrees. The primary effect of increasing the trailing-edge angle was to decrease the loading over the rear portion of the airfoil under lifting conditions. The differences in trailing-edge load increased with Mach number and lift coefficient" (p. 1).

From Summary: "The performance of the turbine component of a J33 turbojet engine was determined over a range of turbine speeds from 8000 to 11,500 rpm.Turbine-inlet temperature was varied from the minimum required to drive the compressor to a maximum of approximately 2000 degrees R at each of several intermediate turbine speeds. Data are presented that show the horsepower developed by the turbine per pound of gas flow."

Tests were conducted in calm water in Langley tank no. 2 and in calm and rough water at an outdoor catapult in order to determine the best way to make a forced landing of an Army A-26 airplane and to determine its probable ditching behavior. These tests were requested by the Air Materiel Command, Army Air Forces, in their letter of March 26, 1943, WEL:AW:50.

Report presenting results of chordwise pressure-distribution measurements on a 45 degree sweptback wing at transonic speeds. The two stations for measuring were located at the 18 percent chord from the root and the 87 percent chord. The changes in pressure distribution with Mach number did not indicate any appreciable net loss in section lift, but did indicate large increases in the section drag and diving moment.

From Introduction: "This paper presents the results of the investigation of the wing-alone and wing-fuelage configurations employing a wing with the quarter-chord line swept back 60^o, aspect ratio 4, taper ratio 0.6, and an NACA 65A006 airfoil section parallel to the free stream."

The teat results showed that with either of the three tail arrangements, the model usually spun in flat attitudes with oscillations about the lateral and longitudinal axes. In general, full reversal of the rudder pedals did not stop the spinning rotation. To make the model satisfactorily meet-the spin-recovery requirements it was found that installation of either a very large ventral fin (l7.9 square feet, full scale) below the tail or a somewhat smaller ventral fin and rudder (12.4 square feet, total . full-scale area) with a rudder throw of at least +/-22deg was required. Either a 21.3-foot tail parachute or a 6.4-foot wing-tip parachute (drag coefficient approximately 0.70) appears necessary as an emergency spin-recovery device during demonstration spins.

"It is shown that for velocities slightly in excess of sonic, the position of detached shock wave located in front of a given body at zero angle of attack may be estimated theoretically to a reasonable degree of accuracy. In case of bodies of revolution the result was simple, but for two-dimensional bodies, pressure coefficient varies with Mach number, and slight difficulty appears. Theory developed compares favorably with available experimental data" (p. 1).

From Summary: "Tests have been made in Langley tank no. I of a dynamic model of the Consolidated Vultee PB2Y-3 airplane. These tests were made using an alternate hull form, the purpose of which was to reduce the bow spray and eliminate the landing instability which are objectionable features of the production design. The major differences from the PB2Y-3 hull included a deeper step to improve the landing stability , and a lengthened forebody and increased beam to reduce the sway in the propellers and on the flaps. The tests showed that the spray characteristics of the revised hull form were much better than that to the production design. In addition the take-off and landing stability of the model with the alternate hull were satisfactory."

From Summary: "Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size)."