Novel tissue mimicking materials have been developed for cancer treatment research. In the present research work, the tissue mimicking material is printed using 3D bioprinting technology. The nanoparticles are homogeneously mixed with tissue mimicking materials to enhance the heating capacity. The thermal conductivity of tissue mimicking materials is measured using a micropipette thermal sensor (MTS). Further, the optimal value is identified based on optimization technique and incorporated into a theoretical model to predict the surface temperature of microsphere. The heat conduction governing equation with Lambert law is numerically solved using COMSOL Multiphysics software. To validate the present simulation results, the experiments are conducted using a continuous laser system.

This thesis project investigates the configuration of an enclosed evaporation chamber with the intention of converting seawater into potable freshwater. The evaporation chamber's sole heat source is provided by a Fresnel lens, located above the chamber, which concentrates sunlight onto a 3-inch diameter focal plate built into the core of the chamber. The design of the evaporation chamber is modeled after a solar still and is coupled with a heat exchanger to boost efficiency of the system. The chamber was designed with the objectives of being portable, lightweight, low cost, corrosion resistant, interchangeable, and size convenient with the goal of producing 1 Liter of freshwater per hour of operation. The evaporation chamber consists of two primary components, a core and an attached arrangement of fins, all of which are heated via the Fresnel lens. A consistent intake of 2 grams/second of saltwater enters from the top of the chamber and is then gravity fed across the fins. Fin orientation has been designed to inhibit the flow rate of water within the chamber, maximizing the surface area of contact with the heated fins. The evaporation chamber was modeled through SOLIDWORKS and underwent a physical optimization study to reduce material usage while …

Interfacial mechanical properties of adhesive joints are very crucial in board applications, including composites, multilayer structures, and biomedical devices. Establishing traction-separation (T-S) relations for interfacial adhesion can evaluate mechanical and structural reliability, robustness, and failure criteria. Due to the short range of interfacial adhesion such as micro to nanoscale, accurate measurements of T-S relations remain challenging. The advent of machine learning (ML) became a promising tool to predict materials behaviors and establish data-driven mechanical models. In this study, we integrated a state-of-the-art ML method, finite element analysis (FEA), and standard experiments to develop data-driven models for characterizing the interfacial mechanical properties precisely. Macroscale force-displacement curves are derived from FEA with incorporation of double cantilever beam tests to generate the dataset for ML model. The eXtreme Gradient Boosting (XGBoost) multi-output regressions and classifier models are used to determine T-S relations with R2 score of 98.8% and locate imperfections at the interface with accuracy of around 80.8%. The outcome of the XGBoost models demonstrated accurate predictions and fast calculation speed, outperforming several other ML methods. Using 3D printed double cantilever beam specimens, the performance of the ML models is validated experimentally for different materials. Furthermore, a XGBoost model-based package is designed to …

This study investigated a new approach to achieving high energy density supercapacitors (SCs) by using high surface area self-activated carbon from waste coffee grounds (WCGs) and modifying 3D printed electrodes' porous structure by varying infill density. The derived activated carbons' surface area, pore size, and pore volume were controlled by thermally treating the WCGs at different temperatures (1000˚C, 1100˚C, and 1200˚C) and post-treating with HCL to remove water-soluble ashes and contaminants that block activated carbon pores. Surface area characterization revealed that the carbon activated at 1000˚C had the highest surface of 1173.48 m2 g-1, and with the addition of HCL, the surface area increased to 1209.35 m2 g-1. This activated carbon was used for fabricating the electrodes based on the surface area and having both micropores and macropores, which are beneficial for charge storage. Direct ink writing (DIW) method was utilized for 3D printing SC electrodes and changing the electrode structure by increasing the infill densities at 30%, 50%, and 100%. Upon increasing the infill densities, the electrodes' mass increased linearly, porosity decreased, and the total surface area increased for the 30% and 50% infill electrodes but decreased for the 100% infill electrode. Cyclic voltammetry (CV) test on the assembled …

Nondestructive testing (NDT) using ultrasound band 1-5 MHz, has been widely used for the early-stage detection of structural failure; however, it fails to detectf material degradation, fatigue, and microcracks. NDT with nonlinear ultrasound (NLU) can detect a microscopic discontinuity or imperfection that may be a source of the second harmonic in the reflected signal. In this research, we focus on creating a metamaterial band filter that filters out nonlinearities induced by the instrument itself. A 1D elastic superlattice (SL) acoustic filter is designed with a bandgap in its frequency spectrum that covers the frequency range of second harmonic. The SL is made of periodically alternating Cu and Sn-Pb solder layers. We conducted analytical and numerical calculations to obtain the appropriate thickness of each layer. The metamaterial in this study has the pass band for the fundamental frequency of 5 MHz and the first stop band centered near the frequency of 10 MHz; 5 MHz was chosen because the second harmonic at 10 MHz can detect 200μm micro-scale damage. Experiments with aluminum as the reference specimen and with SL filter were conducted. A function-generator generates 3 pulses sine signal, within the frequency range from 2.5 MHz to 20MHz. Spectral analysis of …

Sequential single-axis vibration testing strategies often produce over-testing when qualifying system hardware. Multi-axis excitation techniques can simulate realistic service environments, but the hardware and testing strategies needed to do so tend to be costly and complex. Test engineers instead must execute sequential tests on single-axis shaker tables to excite each degree of freedom, which the previous two decades of vibration testing literature have shown to cause extensive over-testing when considering cross-axis responses in assessing the severity of the applied test environments. Traditional assessments assume that the test article responds only in the axis of excitation, but often significant response occurs in the off-axes as well. This paper proposes a method to address the over-testing problem by approximating a simultaneous multi-axis test using readily-available, single-axis shaker tables. By optimizing the angle of excitation and the boundary condition through dynamic test fixture design, the test article can be tested using a Single-Input, Multiple-Output (SIMO) test in a way that approximates a Multiple-Input, Multiple-Output (MIMO) test. This paper shows the proposed method in simulation with a 2D finite element box assembly with removable component (BARC) model attached to springs with variable stiffness. The results include quantified test quality assessment metrics with comparison to …

The use of collection systems for magnetic sorbents such as Magnetic Activated Carbon are discussed in order to gauge their efficacy in marine environments. Two collectors were built and tested, one which utilized a radial orientation of magnets and another with axially placed magnets. The two systems underwent a series of test with differing linear velocities and angular velocities. From the results, the axial system outperformed its radial counterpart, being most effective with a relatively high concentration of discs placed in series. The medium concentration, however, proved increasingly effective with higher velocities, meaning an optimization concentration exists for this design. The radial system was tested with high and low concentrations of small and large magnets, respectively. The larger magnets, although providing less concentration points in the alternating array, proved more effective for the collection of MAC. From these tests several new innovations were suggested, including belt tensioners, add on mechanisms, and a hybridized design in order to fully optimize the collection of MAC.

This dissertation focuses on studying membrane air dehumidification for a membrane moisture exchanger in a membrane heat pump system. The study has two parts: an optimization of membrane moisture exchanger for air dehumidification in the macroscale, and diffusion of water vapor in polymer nanocomposites membrane for humid air dehumidification in the nanoscale. In the first part of the research, the mass transport of water vapor molecules through hydrophilic silica nanochannel chains in hydrophobic polyurethane matrix was studied by simulations and experiments for different membrane moisture exchanger design configurations. The mass transport across the polymer nanocomposite membrane occurs with the diffusion of moist air water vapor molecules in the membrane moisture exchanger in a membrane heat pump air conditioning system for air dehumidification purposes. The hydrophobic polyurethane matrix containing the hydrophilic silica nanochannel chains membrane is responsible for transporting water vapor molecules from the feed side to the permeate side of the membrane without allowing air molecules to pass through.In the second part of the research, diffusion analysis of the polymer nanocomposite membrane were performed in the nanoscale for the polymer nanocomposite membrane. The diffusion phenomena through the polymer, the polymer nanocomposite without modifying the silica surfaces, and the polymer nanocomposite …

Pillared-graphene structure (PGS) is a novel three-dimensional structure consists of parallel graphene sheets that are separated by carbon nanotube (CNT) pillars that is proposed for efficient thermal management of electronics. For microscale simulations, finite element analyses were carried out by imposing a heat flux on several PGS configurations using a Gaussian pulse. The temperature gradient and distribution in the structures was evaluated to determine the optimum design for heat transfer. The microscale simulations also included conducting a mesh-independent study to determine the optimal mesh element size and shape. For nanoscale simulations, Scienomics MAPS software (Materials And Processes Simulator) along with LAMMPS (Large-scale Atomic/ Molecular Massively Parallel Simulator) were used to calculate the thermal conductivity of different configurations and sizes of PGS. The first part of this research included investigating PGS when purely made of carbon atoms using non-equilibrium molecular dynamics (NEMD). The second part included investigating the structure when supported by a copper foil (or substrate); mimicking production of PGS on copper. The micro- and nano-scale simulations show that PGS has a great potential to manage heat in micro and nanoelectronics. The fact that PGS is highly tunable makes it a great candidate for thermal management applications. The simulations were …

A flexible nanofibrous PVDF-BaTiO3 composite material is prepared for impact sensing and biomechanical energy harvesting applications. Dielectric polyvinylidene fluoride (PVDF) and barium titanate (BaTiO3)-PVDF nanofibrous composites were made using the electrospinning process based on a design of experiments approach. The ultrasonication process was optimized using a 2k factorial DoE approach to disperse BaTiO3 particles in PVDF solution in DMF. Scanning electron microscopy was used to characterize the microstructure of the fabricated mesh. The FT-IR and Raman analysis were carried out to investigate the crystal structure of the prepared mesh. Surface morphology contribution to the adhesive property of the composite was explained through contact angle measurements. The capacitance of the prepared PVDF- BaTiO3 nanofibrous mesh was a more than 40% increase over the pure PVDF nanofibers. A comparative study of dielectric relaxation, thermodynamics properties and impact analysis of electrospun polyvinylidene fluoride (PVDF) and 3% BaTiO3-PVDF nanofibrous composite are presented. The frequency dependent dielectric properties revealed micro structural features of the composite material. The dielectric relaxation behavior is further supported by complex impedance analysis and Nyquist plots. The temperature dependence of electric modulus shows Arrhenius type behavior. The observed non-Debye dielectric relaxation in electric loss modulus follows a thermally activated process which …

The recipes of optical radiative properties manipulation are their materials chemistry, nano/microscale geometry, and transport properties of quasiparticle carriers such as photons, phonons, and electrons. The important technical element in optical properties is the dielectric function of materials, which is different for metals, dielectrics, 2D materials, and phase transition materials. Graphene has a unique electrical conductivity profile which have metallic nature depending on the frequency, but also has a negative thermal expansion coefficient that makes graphene unique. Hence, graphene creates wrinkles when deposited on the substrate as temperature decreases to room temperature from high substrate temperature. We also study phase transition material, particularly vanadium dioxide that transitions from insulating to metallic phase based on temperature change; we investigate its role in far-field thermal radiation. Other transition metal oxides are studied as a thermally and electrically tunable plasmonic gratings: Transition metal oxides include vanadium dioxide, tungsten trioxide, and molybdenum trioxide. The work demonstrates plasmonic phenomena and absorptance/emittance tunability. First, surface plasmon polariton along the graphene (SPPG) when wrinkles are formed above the plasmonic grating is studied. The resonance peak shift is modeled for both magnetic polariton (MP) with inductor-capacitor (LC) circuit and SPPG with Fabry-Perot phase change model. Second, the self-adaptive …

Ecological, health and environmental concerns are driving the need for bio-resourced foams for the building industry and for other applications. This is because insulation is one of the most important aspects of the building envelope. Global building insulation is expected to reach USD 27.74 billion in 2022. Conventional insulation materials currently used in buildings are made from nonrenewable products (petroleum, fiber glass). However, they yield increasing unrecyclable eco-unfriendly waste at the end of their lives; styrene and polyurethane generates over 100,000 kg of waste insulation in US alone yearly. This is because they are non-biodegradable and can remain as microplastics in the environment for 1000 years. Polyurethane contains the same amount of energy as coal. Additionally, most of the processing techniques and blowing agents used in this manufacturing of these foams are cancerous and injurious to health when inhaled. Because buildings and their construction together account for 36% of global energy use and 39% of energy-related carbon dioxide emissions annually, there is a need to develop eco-friendly foams that will serve as possible substitutes to the currently used petroleum-based foams. This dissertation examined the development and characterization of eco-friendly foams that were developed using the melt mixing technique of bio-resourced …

In this research work, an innovative method for measurement of thermal conductivity of a small volume of liquids, microsphere, and the single cancer cell is demonstrated using a micro-pipette thermal sensor (MPTS). The method is based on laser point heating thermometry (LPHT) and transient heat transfer. When a single pulse of a laser beam heats the sensor tip which is in contact with the surrounding liquids or microsphere/cells, the temperature change in the sensor is reliant on the thermal properties of the surrounding sample. We developed a model for numerical analysis of the temperature change using the finite element method (FEM) in COMSOL. Then we used MATLAB to fit the simulation result with experiment data by multi-parameter fitting technique to determine the thermal conductivity. To verify the accuracy in the measurement of the thermal conductivity by the MPTS method, a 10µl sample of de-ionized (DI) water, 50%, and 70% propylene glycol solution were measured with deviation less than 2% from reported data. Also, to demonstrate that the method can be employed to measure microparticles and a single spherical cell, we measured the thermal conductivity of poly-ethylene microspheres with a deviation of less than 1% from published data. We estimated the …

While ozone design values have decreased since 2000, the values measured in Denton Airport South (DEN), an exurban region in the northwest tip of the Dallas-Fort Worth (DFW) metroplex, remains above those measured in Dallas Hinton (DAL) and Fort Worth Northwest (FWNW), two extremely urbanized regions; in addition, all three sites remained in nonattainment of National Ambient Air Quality Standards (NAAQS) ozone despite reductions in measured NOx and CO concentrations. The region's inability to achieve ozone attainment is tied to its concentration of total non-methane organic compounds (TNMOC). The mean concentration of TNMOC measured at DAL, FWNW, and DEN between 2000 and 2018 were 67.4 ± 1.51 ppb-C, 89.31 ± 2.12 ppb-C, and 220.69 ± 10.36 ppb-C, respectively. Despite being the least urbanized site of the three, the TNMOC concentration measured at DEN was over twice as large as those measured at the other two sites. A factor-based source apportionment analysis using positive matrix factorization technique showed that natural gas was a major contributing source factor to the measured TNMOC concentrations at all three sites and the dominant source factor at DEN. Natural gas accounted for 32%, 40%, and 69% of the measured TNMOC concentration at DAL, FWNW, and DEN, …

Incorporating insulation material with phase change materials (PCMs) could help enhance the insulation capability for a refrigerator system. The phase change material can absorb or release large amount of latent heat of fusion depending on surrounding temperatures for efficient thermal management. This research focuses on how incorporating PCM to the conventional PU foam insulation affects the inside temperatures of the refrigerator system and in-turn helps in conserving energy by reducing the compressor run time. It was found that only 0.25-inch-thick PCM layer in insulation can certainly benefit the refrigerators by reducing the amount of electricity consumption and thus increasing the total energy savings through the numerical study results via COMSOL Multiphysics in this study. This work aims to investigate a PCM-incorporated insulation material to accomplish the enhancement of thermal insulation performance for refrigerators.

The research focuses on the synthesis and application of multifunctional lignocellulosic biomass bioadsorbent and nanobiocomposites for water purification. A bioadsorbent was prepared from kenaf fiber by self-activation without the use of any toxic chemicals in an innovative method. Silver nanoparticles were synthesized by the green route and then impregnated on the surface of kenaf-based activated carbon (KAC), and hemp fibers by heating and photoirradiation. The formation of hemp-based and kenaf-based silver nanocomposites was confirmed using an environmental scanning electron microscope and energy-dispersive x-ray spectroscopy. Low-cost benign nanoadsorbents demonstrated excellent capabilities for the anionic dye Congo red (CR) and cationic dye brilliant green (BG) degradation, inorganic heavy metals [Cu (II), Pb (II), and Cd (II)] adsorption and antibacterial activities. Antibacterial test via a modified disc diffusion method and minimum inhibitory concentrations was assessed towards the pathogenic strains of bacteria, E. coli and S. aureus. A working portable point-of-use filter was designed and developed, with the filter column encapsulated with nanobiocomposites for the removal of multi-metals and dye. Water samples collected from a wastewater treatment plant in Texas and a mining site in Mexico were used to determine the efficacy of the nanobiocomposites columned in the filter. A comparative analysis was also …

Several active methods, which requires external control systems and moving parts, have been developed to control the fiber orientation during 3D printing. Active mechanisms like rotating nozzle, impeller, and magnetic field have been integrated to realize complex internal fiber structures. In this study, instead of using active methods, I investigate a passive method for controlling the fiber orientation without any moving parts or additional mechatronics added in the printing process. Composites of polydimethylsiloxane (PDMS) and glass fibers (GF) are 3D printed. Channels, such as helicoid, are designed and integrated to guide the ink flow and passively result in different pre-alignment of fibers before the ink flow into narrow nozzle space. While passing through the designed channels, the fibers orient due to the shear between channel walls and the ink. The effect of helicoids with different pitch sizes are investigated via mechanical experiments, microstructural analysis, and numerical simulations. The results show that both surface to volume ratio and helix angle of the channel affect pre-alignment of fiber orientation at the entry of nozzle. The internal fiber structures lead to enhanced and tunable mechanical properties of printed composites. Pitch size 7-9 mm (helix angle of 7.92- 10.15o) is found to be optimal …

Non-imaging Fresnel lenses have been playing an important role in improving the efficiency of the solar energy systems. Many researchers and scientists have devoted their research to optimize the design of the Fresnel lenses. Before it can contribute to energy efficiency increase, a Fresnel lens with optimized design will first need to be fabricated with the most cost-effective method as well as the best quality fabrication as possible. If targeted in a commercial market, feasibility of mass production with a minimum fabrication time would also be a consideration. To bring the design optimization of a Fresnel lens from a conceptual theory to a real-life increase in energy efficiency, the lens needs to be fabricated, tested, compared, and analyzed. This research thesis is intended to explore the performance of the lenses with optimized design through experimental investigations. The design optimization was achieved by a previous PhD student at UNT. A total of six lenses fabricated with four different methods along with two purchased lenses were tested with two different approaches. Multiple testing routes were conducted within a 10-month period to observe the effects of material decomposition and degradation on the lens performance. The resulting experimental data has provided a solid base …

In this research thermal properties enhancement of phase change material (PCM) using boron nitride nanomaterials such as nanoparticles and nanotubes is studied through experimental measurements, finite element method (FEM) through COMSOL 5.3 package and molecular dynamics simulations via equilibrium molecular dynamics simulation (EMD) with the Materials and Process Simulations (MAPS 4.3). This study includes two sections: thermal properties enhancement of inorganic salt hydrate (CaCl2∙6H2O) as the phase change material by mixing boron nitride nanoparticles (BNNPs), and thermal properties enhancement of organic phase change material (paraffin wax) as the phase change material via encapsulation into boron nitride nanotubes (BNNTs). The results of the proposed research will contribute to enhance the thermal transport properties of inorganic and organic phase change material applying nanotechnology for increasing energy efficiency of systems including electronic devices, vehicles in cold areas to overcome the cold start problem, thermal interface materials for efficient heat conduction and spacecraft in planetary missions for efficient thermal managements.

Waste-heat-to-power (WHP) recovers electrical power from exhaust heat emitted by industrial and commercial facilities. Waste heat is available in enormous quantities. The U.S. Department of Energy estimates 5-13 quadrillion BTUs/yr with a technical potential of 14.6 GW are available and could be utilized to generate power by converting the heat into electricity. The research proposed here will define a system that can economically recover energy from waste heat through a thermal regenerative electrochemical system. The primary motivation came from a patent and the research sponsored by the National Renewable Energy Laboratory (NREL). The proposed system improves on this patent in four major ways: by using air/oxygen, rather than hydrogen; by eliminating the cross diffusion of counter ions and using a dual membrane cell design; and by using high concentrations of electrolytes that have boiling points below water. Therefore, this system also works at difficult-to-recover low temperatures. Electrochemical power is estimated at 0.2W/cm2, and for a 4.2 M solution at 1 L/s, the power of a 100 kW system is 425 kW. Distillation energy costs are simulated and found to be 504 kJ/s for a 1 kg/s feed stream. The conversion efficiency is then calculated at 84%. The Carnot efficiency for …

Recent advances in manufacturing and growing concerns on the sustainability of aviation environment have led to a remarkable interest in electrical unmanned aerial systems (UASs) in the past decade. Among various UAS types, the newly designed quadrotor biplane tailsitter class is capable of delivering a wide range of civilian and military tasks, relying on its Vertical Take-Off and Landing (VTOL) capability as well as great maneuverability. Nevertheless, as such UASs employ rotors to generate thrust, and wings to generate lift, and operate at less-understood low to mid-Reynolds flow regime, they experience complicated flight aerodynamics with a noise generation mechanism which is different from common aircrafts. The present work aims at addressing this knowledge gap by studying the aerodynamics and aeroacoustics of a UAS of this type designed by the Army Research Lab. High-fidelity computational fluid dynamics (CFD) simulations are carried out for a wide range of operating conditions to understand the physics involved in the UAS aerodynamics and characterize its performance. Relying on the CFD results, a physics-informed reduced order model (ROM) is developed based on machine learning algorithms, to predict the propellers effects on the wings and calculate the dominant loads. The results of this study indicate that the …

An enhanced thermal imaging concept made possible through the development of a gradient-indexed metamaterial infrared detector that offers broadband transmission and reflection in THz waves. This thesis proposes a proof of feasibility for a metamaterial infrared detector containing an anti-reflective coating with various geometrically varying periodic metasurfaces, a gradient-indexed dielectric multilayer for near-perfect longpass filtering, and a gradient index of refraction (GRIN) metalens for enhanced focal plane thermal imaging. 2D Rigorous Coupled-Wave Analysis (RCWA) is used for understanding the photonic gratings performance based on material selection and varying geometric structure. Finite Difference Time Domain (FDTD) is used to characterize performance for a diffractive metalens by optimizing the radius and arrangement of cylindrical nanorods to create a desired phase profile that can achieve a desired focal distance for projections on a detector for near- to far-infrared thermal imaging. Through combining a micromachined anti-reflective coating, a near-perfect longpass filter, and metamaterial GRIN metalens, infrared/THz focal plane thermal imaging can obtain faster photo-response and image quality at targeted wavelengths, which allows for scientific advancements in electro-optical devices for the Department of Defense, aerospace, and biochemical detection applications.

Additively manufactured (AM) 316L and 17-4PH stainless steel parts, concretely made by laser powder bed fusion (L-PBF), are characterized and micro-mechanical properties of those steels are analyzed. This study also explored and extended to proton irradiation and small-scale mechanical testing of those materials, to investigate how irradiation affects microstructural evolution and thus mechanical properties at the surface level, which could be detrimental in the long term in nuclear applications. In-depth anisotropy analysis of L-PBF 316L stainless steel parts with the variations of volumetric energy density, a combined study of nanoindentation with EBSD (electron backscatter diffraction) mapping is shown to be an alternative methodology for enriching qualification protocols. Each grain with a different crystallographic orientation was mapped successfully by proper indentation properties. <122> and <111> oriented grains displayed higher than average indentation modulus and hardness whereas, <001>, <101>, and <210> oriented grains were found to be weaker in terms of indentation properties. Based on an extensive nanoindentation study, L-PBF 17-4 PH stainless steels are found to be very sensitive to high load rates and irradiation further escalates that sensitivity, especially after a 0.25 s-1 strain rate. 3D porosity measurement via X-ray microscope ensures L-PBF stainless steel parts are of more than …

Immersed boundary (IB) methods are attractive due to their ability to simulate flow over complex geometries on a simple Cartesian mesh. Unlike conformal grid formulation, the mesh does not need to conform to the shape and orientation of the boundary. This eliminates the need for complex mesh and/or re-meshing in simulations with moving/morphing boundaries, which can be cumbersome and computationally expensive. However, the imposition of boundary conditions in IB methods is not straightforward and numerous modifications and refinements have been proposed and a number of variants of this approach now exist. In a nutshell, IB methods in the literature often suffer from numerical oscillations, implementation complexity, time-step restriction, burred interface, and lack of generality. This limits their ability to mimic conformal grid results and enforce Neumann boundary conditions. In addition, there is no generic IB capable of solving flow with multiple potentials, closely/loosely packed structures as well as IBs of infinitesimal thickness. This dissertation describes a novel 2$ ^{\text{nd}} $ order direct forcing immersed boundary method designed for simulation of two- and three-dimensional incompressible flow problems with complex immersed boundaries. In this formulation, each cell cut by the IB is reshaped to conform to the shape of the IB. IBs …