In this research, an elastic cylinder that utilized vortex-induced vibration (VIV) was applied to improve convective heat transfer rates by disrupting the thermal boundary layer. Rigid and elastic cylinders were placed across a fluid channel. Vortex shedding around the cylinder led to the periodic vibration of the cylinder. As a result, the flow-structure interaction (FSI) increased the disruption of the thermal boundary layer, and therefore, improved the mixing process at the boundary. This study aims to improve convective heat transfer rate by increasing the perturbation in the fluid flow. A three-dimensional numerical model was constructed to simulate the effects of different flow channel geometries, including a channel with a stationary rigid cylinder, a channel with a elastic cylinder, a channel with two elastic cylinders of the same diameter, and a channel with two elastic cylinders of different diameters. Through the numerical simulations, the channel maximum wall temperature was found to be reduced by approximately 10% with a stationary cylinder and by around 17% when introducing an elastic cylinder in the channel compared with the channel without the cylinder. Channels with two-cylinder conditions were also studied in the current research. The additional cylinder with the same diameter in the fluid channel …

Ground source heat pump (GSHP) uses earth’s heat to heat or cool space. Absorbing heat from earth or rejecting heat to the earth, changes soil’s constant temperature over the multiple years. In this report we have studied about Soil temperature change over multiple years due to Ground loop heat exchanger (GLHE) for Zero Energy Research Laboratory (ZØE) which is located in Discovery Park, University of North Texas, Denton, TX. We did 2D thermal analysis GLHP at particular Depth. For simulation we have used ANSYS workbench for pre-processing and FLUENT ANYS as solver. TAC Vista is software that monitors and controls various systems in ZØE. It also monitors temperature of water inlet/outlet of GLHE. For Monitoring Ground temperatures at various depths we have thermocouples installed till 8ft from earth surface, these temperatures are measured using LabVIEW. From TAC Vista and LabVIEW Reading’s we have studied five parameters in this report using FLUENT ANSYS, they are; (1) Effect of Time on soil Temperature change over Multi-years, (2) Effect of Load on soil temperature change over Multi-years, (3) Effect of Depth on soil temperature change over Multi-years, (4) Effect of Doubling ΔT of inlet and outlet of GLHE on soil temperature change over …

A method to distinguish human level of comfort has been developed by using a thermal camera, physiological sensors, and a surroundings sensor. The method has successfully collected data from hominal facial features, breathing rate, skin temperature, room temperature, blood volume pressure, relative humidity, and air velocity. Participants from all genders and races were involved in two sessions of a human comfort experiment including a psychology survey session. The variables, such as room temperature and clothing are controlled to maintain steady test conditions. The region of interest was determined by body temperature and facial temperature as registered by the thermal imaging camera. To experience different levels of discomfort, participants were required to perform two different activities. The first session included an activity on the air resistance elliptical and the second session required the subjects to remain steady in front of a fan. The data was subsequently compared on all subjects to determine whether human discomfort and comfort can be predicted by using various approaches. The parameters of discomfort and comfort were simulated to characterize human levels of comfort. According to arrangement of correlation among thermal comfort responses, blood volume pressure, skin temperature, respiration, and skin conduction, we are be able to …

Recent development of additive manufacturing technologies has led to lack of information on the base materials being used. A need arises to know the mechanical behaviors of these base materials so that it can be linked with macroscopic mechanical behaviors of 3D network structures manufactured from the 3D printer. The main objectives of my research are to characterize properties of a material for an additive manufacturing method (commonly referred to as 3D printing). Also, to model viscoelastic properties of Procast material that is obtained from 3D printer. For this purpose, a 3D CAD model is made using ProE and 3D printed using Projet HD3500. Series of uniaxial tensile tests, creep tests, and dynamic mechanical analysis are carried out to obtained viscoelastic behavior of Procast. Test data is fitted using various linear and nonlinear viscoelastic models. Validation of model is also carried out using tensile test data and frequency sweep data. Various other mechanical characterization have also been carried out in order to find density, melting temperature, glass transition temperature, and strain rate dependent elastic modulus of Procast material. It can be concluded that melting temperature of Procast material is around 337°C, the elastic modulus is around 0.7-0.8 GPa, and yield …

The sample used for evaporative cooling system is Fabric defender 750 with Shelltite finish. From the experimental data and equations we have diffusion coefficient of 20.9 ± 3.71 x 10-6 m2/s for fabric with one layer with 17%-20% fluctuations from the theory, 27.8 ± 4.5 x 10-6 m2/s for fabric with two layers with 6%-14% fluctuations from the theory and 24.9 ± 4.1 x 10-6 m2/s for fabric with three layers with 13%-16% fluctuations from the theory. Since the thickness of the fabric increases so the mass transport rate decreases so the mass transport resistance should be increases. The intrinsic mass resistances of Fabri-1L, Fabri-2L and Fabri-3L are respectively 104 ± 10.2 s/m, 154 ± 23 s/m and 206 ± 26 s/m from the experiment.

Numerical simulation is used to investigate the accuracy of a direct-contact device for measuring skin-surface temperature. A variation of thermal conductivity of the foam has greater effect on the error rather than a variation of the blood perfusion rate. For a thermal conductivity of zero, an error of 1.5 oC in temperature was identified. For foam pad conductivities of 0.03 and 0.06 W/m-oC, the errors are 0.5 and 0.15 oC. For the transient study, with k=0 W/m-oC, it takes 4,900 seconds for the temperature to reach steady state compared with k=0.03 W/m-oC and k=0.06 W/m-oC where it takes 3,000 seconds. The configuration without the foam and in presence of an air gap between the skin surface and the sensor gives the most uniform temperature profile.

Joining two dissimilar metals, specifically Mg and Al alloys, using conventional welding techniques is extraordinarily challenging. Even when these alloys are able to be joined, the weld is littered with defects such as cracks, cavities, and wormholes. The focus of this project was to use friction stir welding to create a defect-free joint between Al 2139 and Mg WE43. The stir tool used in this project, made of H13 tool steel, is of fixed design. The design included an 11 mm scrolled and concave shoulder in addition to a 6 mm length pin comprised of two tapering, threaded re-entrant flutes that promoted and amplified material flow. Upon completion of this project an improved experimental setup process was created as well as successful welds between the two alloys. These successful joints, albeit containing defects, lead to the conclusion that the tool used in project was ill fit to join the Al and Mg alloy plates. This was primarily due to its conical shaped pin instead of the more traditional cylindrical shaped pins. As a result of this aggressive pin design, there was a lack of heat generation towards the bottom of the pin even at higher (800-1000 rpm) rotation speeds. This …

Magnesium alloys are a popular research topic for structural applications because they have a lower density than conventional structural materials, including steel, titanium, and aluminum; however, the reliability and safety of their mechanical properties must be further proven. An important mechanical property for this purpose is fracture toughness, which is the measure of the material's resistance to crack propagation. In this study, a model of an experiment to investigate the fracture toughness of a magnesium alloy WE43 before and after friction stir processing (FSP) is developed, and the results are compared to those produced by a digital image correlation (DIC) system during an experiment from another paper. The model results of the material before FSP matched well with the DIC results, but the model of the material after FSP only partially matches the DIC results. In addition, a theoretical approach to calculating the standard fracture toughness value, KIc, from the modeling results is proposed, and is found to be a conservative approach.

There is a wide range of applications for 3D printing technology with an additive manufacturing such as aerospace, automotive, marine and oil/gas, medical, consumer, electronics, building construction, and many others. There have been many pros and cons for 3D additive manufacturing. Even though 3D printing technology has many advantages: freedom to design and innovate without penalties, rapid iteration through design permutations, excellence mass customization, elimination of tolling, green manufacturing, minimal material wastes, energy efficiency, an enablement of personalized manufacturing. 3D additive manufacturing still has many disadvantages: unexpected pre- and post-processing requirement, high-end manufacturing, low speed for mass production, high thermal residual stress, and poor surface finish and dimensional accuracy, and many others. Especially, the issues for 3D additive manufacturing are on high cost for process and equipment for high-end manufacturing, low speed for mass production, high thermal residual stress, and poor surface finish and dimensional accuracy. In particular, it is relatively challenging to produce casting products with lattice or honeycomb shapes having sophisticated geometries. In spite of the scalable potential of periodic cellular metals to structural applications, the manufacturing methods of I∙AM Casting have been not actively explored nor fully understood. A few qualitative studies of I∙AM Casting has been …

This research work is focused on a conceptual combination of membrane-based energy recovery ventilator (ERV) and phase change material (PCM) to provide energy savings in building heating, ventilation & air-conditioning (HVAC) systems. An ERV can recover thermal energy and moisture between the outside fresh air (OFA) entering into the building and the exhaust air (EA) leaving from the building thus reducing the energy consumption of the HVAC system for cooling and heating the spaces inside the building. The membranes were stacked parallel to each other forming adjacent channels in a counter-flow arrangement for OFA and EA streams. Heat and moisture is diffused through the membrane core. Flat-plate encapsulated PCM is arranged in OFA duct upstream/downstream of the ERV thereby allowing for further reduction in temperature by virtue of free cooling. Paraffin-based PCMs with a melting point of 24°C and 31°C is used in two different configurations where the PCM is added either before or after the ERV. Computational fluid dynamics (CFD), and heat and mass transfer modeling is employed using COMSOL Multiphysics v5.3 to perform the heat and mass transfer analysis for the membrane-based ERV and flat-plate PCMs. An 8-story office building was considered to perform building energy simulation using …

The goal of this dissertation is to demonstrate that data from a remotely located building can be utilized for energy modeling of a similar type of building and to demonstrate how to use this remote data without physically moving the data from one server to another using Virtual Information Fabric Infrastructure (VIFI). In order to achieve this goal, firstly an EnergyPlus model was created for Greek Life Center, a campus building located at University of North Texas campus at Denton in Texas, USA. Three thermal comfort models of Fanger model, Pierce two-node model and KSU two-node model were compared in order to find which one of these three models is most accurate to predict occupant thermal comfort. This study shows that Fanger's model is most accurate in predicting thermal comfort. Secondly, an experimental data pertaining to lighting usage and occupancy in a single-occupancy office from Carnegie Mellon University (CMU) has been implemented in order to perform energy analysis of Greek Life Center assuming that occupants in this building's offices behave similarly as occupants in CMU. Thirdly, different data types, data formats and data sources were identified which are required in order to develop a city-scale urban building energy model (CS-UBEM). …

A particle image velocimetry (PIV) computer software is analyzed in this work by applying automatic differentiation on it. We create two artificial images that contained particles that where moved with a known velocity field over time. These artificial images were created with parameters that we would have on real PIV experiments. Then we applied a PIV software to find the velocity output vectors. As we mentioned before, we applied automatic differentiation through all the algorithm to track the derivatives of the output vectors regarding interesting parameters declared as inputs. By analyzing these derivatives we analyze the sensitivity of the output vectors to changes on each one of the parameters analyzed. One of the most important derivatives calculated in this project was the derivative of the output regarding the image intensity. In future work we plan to use this derivative combined with the intensity probability distribution of each image pixel, to find PIV uncertainties. If we achieve this goal we will find an uncertainty method that will save computational power and will give uncertainty values with computer accuracy.

Pillared-graphene structure (PGS) is a novel three-dimensional structure consists of parallel graphene sheets that are separated by carbon nanotube (CNT) pillars that is proposed for efficient thermal management of electronics. For microscale simulations, finite element analyses were carried out by imposing a heat flux on several PGS configurations using a Gaussian pulse. The temperature gradient and distribution in the structures was evaluated to determine the optimum design for heat transfer. The microscale simulations also included conducting a mesh-independent study to determine the optimal mesh element size and shape. For nanoscale simulations, Scienomics MAPS software (Materials And Processes Simulator) along with LAMMPS (Large-scale Atomic/ Molecular Massively Parallel Simulator) were used to calculate the thermal conductivity of different configurations and sizes of PGS. The first part of this research included investigating PGS when purely made of carbon atoms using non-equilibrium molecular dynamics (NEMD). The second part included investigating the structure when supported by a copper foil (or substrate); mimicking production of PGS on copper. The micro- and nano-scale simulations show that PGS has a great potential to manage heat in micro and nanoelectronics. The fact that PGS is highly tunable makes it a great candidate for thermal management applications. The simulations were …

A flexible nanofibrous PVDF-BaTiO3 composite material is prepared for impact sensing and biomechanical energy harvesting applications. Dielectric polyvinylidene fluoride (PVDF) and barium titanate (BaTiO3)-PVDF nanofibrous composites were made using the electrospinning process based on a design of experiments approach. The ultrasonication process was optimized using a 2k factorial DoE approach to disperse BaTiO3 particles in PVDF solution in DMF. Scanning electron microscopy was used to characterize the microstructure of the fabricated mesh. The FT-IR and Raman analysis were carried out to investigate the crystal structure of the prepared mesh. Surface morphology contribution to the adhesive property of the composite was explained through contact angle measurements. The capacitance of the prepared PVDF- BaTiO3 nanofibrous mesh was a more than 40% increase over the pure PVDF nanofibers. A comparative study of dielectric relaxation, thermodynamics properties and impact analysis of electrospun polyvinylidene fluoride (PVDF) and 3% BaTiO3-PVDF nanofibrous composite are presented. The frequency dependent dielectric properties revealed micro structural features of the composite material. The dielectric relaxation behavior is further supported by complex impedance analysis and Nyquist plots. The temperature dependence of electric modulus shows Arrhenius type behavior. The observed non-Debye dielectric relaxation in electric loss modulus follows a thermally activated process which …

Programmable matter is a material whose properties can be programmed to achieve particular shapes or mechanical properties upon command. This is an essential technique that could one day lead to morphing aircraft and ground vehicles. Metamaterials are the rationally designed artificial materials whose properties are not observed in nature. Their properties are typically controlled by geometry rather than chemical compositions. Combining metamaterials with a programmable function will create a new area in the intelligent material design. The objective of this study is to design and demonstrate a tunable metamaterial and to investigate its thermo-mechanical behavior. An integrated approach to the metamaterial design was used with analytical modeling, numerical simulation, and experimental demonstration. The dynamic thermo-mechanical analysis was used to measure base materials' modulus and thermal expansion coefficient as a function of temperature. CPS, the unit cell of the metamaterial, is composed of circular holes and slits. By decomposing kinematic rotation of the arm and elastic deformation of a bi-material hinge, thermo-mechanical constitutive models of CPS were developed and it was extended to 3D polyhedral structures for securing isotropic properties. Finite element based numerical simulations of CPS and polyhedral models were conducted for comparison with the analytical model. 3D printing of …

This research demonstrates the use of friction stir welding (FSW) to join dissimilar (Al-Mg) metal alloys. The main challenges in joining different, dissimilar metal alloys is the formation of brittle intermetallic compounds (IMCs) in the stir zone affecting mechanical properties of joint significantly. In this present study, FSW joining process is used to join aluminum alloy AA2139 and magnesium alloy WE43. The 9.5 mm thick plates of AA2139 and WE43 were friction stir butt welded. Different processing parameters were used to optimize processing parameters. Also, various weldings showed a crack at interface due to formation of IMCs caused by liquation during FSW. A good strength sound weld was obtained using processing parameter of 1200 rev/min rotational speed; 76.2 mm/min traverse speed; 1.5 degree tilt and 0.13 mm offsets towards aluminum. The crack faded away as the tool was offset towards advancing side aluminum. Mostly, the research was focused on developing high strength joint through microstructural control to reduce IMCs thickness in Al-Mg dissimilar weld joint with optimized processing parameter and appropriate tool offset.

One of the major goal of the researchers is to reduce energy loss including nanoscale to the structural level. For instance, around 65% of fuel energy is lost during the propulsion of the automobiles, where 11% of the loss happens at tires due to rolling friction. Out of that tire loss, 90 to 95% loss happens due to hysteresis of tire materials. This dissertation focuses on multiscale modeling techniques in order to facilitate the discovery new rubber materials. Enhanced coarse-grained models of elastomers (thermoplastic polyurethane elastomer and natural rubber) are constructed from full-atomic models with reasonable repeat units/beads associated with pressure-correction for non-bonded interactions of the beads using inverse Boltzmann method (IBM). Equivalent continuum modeling is performed with volumetric/isochoric loading to predict macroscopic mechanical properties using molecular mechanics (MM) and molecular dynamics (MD). Glass-transition and rate-dependent mechanical properties along with hysteresis loss under uniaxial deformation is predicted with varying composition of the material. A statistical non-Gaussian treatment of a rubber chain is performed and linked with molecular dynamics in order predict hyperelastic material constants without fitting with any experimental data.

Due to the multi-tasking and miniaturization of electronic devices, faster heat transfer is required from the device to avoid the thermal failure. Die-attached polymer adhesives are used to bond the chips in electronic packaging. These adhesives have to hold strong mechanical, thermal, dielectric, and moisture resistant properties. As polymers are insulators, heat conductive particles are inserted in it to enhance the thermal flow with an attention that there would be no electrical conductivity as well as no reduction in dielectric strength. This thesis focuses on the characterization of polymer nanocomposites for thermal and electrical properties with experimental and computational tools. Platelet geometry of hexagonal boron nitride offers highly anisotropic properties. Therefore, their alignment and degree of orientation offers tunable properties in polymer nanocomposites for thermal, electrical, and mechanical properties. This thesis intends to model the anisotropic behavior of thermal and dielectric properties using finite element and molecular dynamics simulations as well as experimental validation.

This thesis is an experimental study of the fluidization of binary mixture in particulate flows. A fluidized bed with two distributors was built with water being used as carrying fluid. Three types of solid particles of nylon, glass and aluminum of the same size and different densities are used in the experiments. The wall effect on a single particle fluidization, the fluidization of binary mixture of large density difference (nylon and aluminum of density ratio of 0.42), and the fluidization of binary mixture of close density (glass and aluminum with density ratio of 0.91) were investigated. Also, the effect of distributors on mono-disperse and bi-disperse particle fluidization was investigated. Results show that the presence of narrow walls reduces the minimum fluidization velocity for a single particle by as much as nearly 40%. Also, in the case of binary mixture of close density particles, uniform mixing was easily achieved and no segregation was observed, but in the case of large density difference particles, there exists significant segregation and separation. At high velocity, the uniform distributor behaves like a transport bed. To achieve a full bed in the single jet, it requires 1.5 times velocity of the uniform distributor. This behavior determines …

Campus dormitories for the University of North Texas house over 5500 students per year; each one of them requires certain comfortable living conditions while they live there. There is an inherit amount of money required in order to achieve minimal comfort levels; the cost is mostly natural gas for water and room heating and electricity for cooling, lighting and peripherals. The US Department of Energy has developed several programs to aid in performing energy simulations to help those interested design more cost effective building designs. Energy-10 is such a program that allows users to conduct whole house evaluations by reviewing and altering a few parameters such as building materials, solar heating, energy efficient windows etc. The idea of this project was to recreate a campus dormitory and try to emulate existent energy consumption then try to find ways of lowering that usage while maintaining a high level of personal comfort.

In this study the author reports the effects of surface roughness on dynamic behavior of water droplets on different types of rough structures. First, the influence of roughness geometry on the Wenzel/ Cassie-Baxter transition of water droplets on one-tier (solid substrates with Si micropillars) surfaces is studied (Chapter 3). In order to address distinct wetting behaviors of the advancing and receding motions, the author investigates the Wenzel/ Cassie-Baxter transition of water droplets on one-tier surfaces over a wide range of contact line velocities and droplet volumes in both advancing and receding movements. The discussions are strengthened by experimental results. According to the author’s analysis, the advancing contact zone tends to follow the Cassie-Baxter behavior for a wider range of geometric ratios than the receding contact zone. Physical phenomena such as advancing contact line rolling mechanism and the pinning of the receding contact line are introduced to justify distinct transition points of the advancing and receding movements respectively. Based on the analysis provided in Chapter 3, the author experimentally investigates the contact line fluctuations and contact line friction coefficients of water droplets on smooth, one-tier, and two-tier (with carbon nanotubes (CNTs) grown on Si micropillars) surfaces in Chapters 4 and 5. …

The electromagnetic shielding effectiveness of kenaf bast fiber based composites with different iron oxide impregnation levels was investigated. The kenaf fibers were retted to remove the lignin and extractives from the pores in fibers, and then magnetized. Using the unsaturated polyester and the magnetized fibers, kenaf fiber based composites were manufactured by compression molding process. The transmission energies of the composites were characterized when the composite samples were exposed under the irradiation of electromagnetic (EM) wave with a changing frequency from 9 GHz to 11 GHz. Using the scanning electron microscope (SEM), the iron oxide nanoparticles were observed on the surfaces and inside the micropore structures of single fibers. The SEM images revealed that the composite’s EM shielding effectiveness was increased due to the adhesion of the iron oxide crystals to the kenaf fiber surfaces. As the Fe content increased from 0% to 6.8%, 15.9% and 18.0%, the total surface free energy of kenaf fibers with magnetizing treat increased from 44.77 mJ/m2 to 46.07 mJ/m2, 48.78 mJ/m2 and 53.02 mJ/m2, respectively, while the modulus of elasticity (MOE) reduced from 2,875 MPa to 2,729 MPa, 2,487 MPa and 2,007 MPa, respectively. Meanwhile, the shielding effectiveness was increased from 30-50% to 60-70%, …

The recipes of optical radiative properties manipulation are their materials chemistry, nano/microscale geometry, and transport properties of quasiparticle carriers such as photons, phonons, and electrons. The important technical element in optical properties is the dielectric function of materials, which is different for metals, dielectrics, 2D materials, and phase transition materials. Graphene has a unique electrical conductivity profile which have metallic nature depending on the frequency, but also has a negative thermal expansion coefficient that makes graphene unique. Hence, graphene creates wrinkles when deposited on the substrate as temperature decreases to room temperature from high substrate temperature. We also study phase transition material, particularly vanadium dioxide that transitions from insulating to metallic phase based on temperature change; we investigate its role in far-field thermal radiation. Other transition metal oxides are studied as a thermally and electrically tunable plasmonic gratings: Transition metal oxides include vanadium dioxide, tungsten trioxide, and molybdenum trioxide. The work demonstrates plasmonic phenomena and absorptance/emittance tunability. First, surface plasmon polariton along the graphene (SPPG) when wrinkles are formed above the plasmonic grating is studied. The resonance peak shift is modeled for both magnetic polariton (MP) with inductor-capacitor (LC) circuit and SPPG with Fabry-Perot phase change model. Second, the self-adaptive …

Non-imaging Fresnel lenses have been playing an important role in improving the efficiency of the solar energy systems. Many researchers and scientists have devoted their research to optimize the design of the Fresnel lenses. Before it can contribute to energy efficiency increase, a Fresnel lens with optimized design will first need to be fabricated with the most cost-effective method as well as the best quality fabrication as possible. If targeted in a commercial market, feasibility of mass production with a minimum fabrication time would also be a consideration. To bring the design optimization of a Fresnel lens from a conceptual theory to a real-life increase in energy efficiency, the lens needs to be fabricated, tested, compared, and analyzed. This research thesis is intended to explore the performance of the lenses with optimized design through experimental investigations. The design optimization was achieved by a previous PhD student at UNT. A total of six lenses fabricated with four different methods along with two purchased lenses were tested with two different approaches. Multiple testing routes were conducted within a 10-month period to observe the effects of material decomposition and degradation on the lens performance. The resulting experimental data has provided a solid base …