Report presenting an investigation in the 19-foot pressure tunnel to determine the nacelle drag, the cowling-air flow, and the propeller characteristics of a model of a high-performance military airplane. The model is fitted with NACA D(sub S)-type engine cowlings and with propellers embodying NACA 16-series airfoil sections. Results regarding the propeller characteristics, drag and cowling-air flow with the propeller removed, the effect of propeller on flow through cowling, and the influence of cooling requirements on airplane performance are provided.

From Introduction: "The purpose of this analysis was to investigate the use of function of intake-manifold temperature and pressure, exhaust back pressure, and engine speed in place of a ventri as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."

Abstract: Experiments on colloid milling and pumping show that uranium trioxide, when carefully dehydrated, can be dispersed in water to form a relatively stable slurry, suitable for a homogeneous slurry pile. At temperatures considerably below those of anticipated pile operation particle size growth occurs attended by increase in settling rate and decrease in viscosity. Theses properties of the slurries may be strongly affected by impurities present as well as by special operating conditions.

Effect of aquadag coating on noise reduction in polyethylene coaxial cable was tested. A satisfactory combination of coaxial cables and connectors interconnecting sources of small ion currents or ionizing impulses with the measuring device is described.

Bi-Pb eutectic and pure Bi penetration of graphites of various densities under 300 degrees C and pressures up to 20 psi was found be of the order of magnitude of 1.0 g/cm(2) and was uniform throughout the graphite. Bi was absorbed less than the eutectic but the oxidation rate of Bi would be prohibitive. There was heavy nitriding in N atmospheres with the Bi and the eutectic.

Report detailing values of x-ray lives and limits for trans-uranic elements. Formulas and methods are detailed throughout the report.

Report presenting a convenient technical method to evaluate changes in the airfoil characteristics resulting from an extension of the chord at the trailing edge of a propeller blade section. The method determines the change in the angle of zero lift, the ideal angle of attack, and the difference in these angles as a function of the angle and length of the trailing-edge extension.

From Summary: "Tests on the B-34 fin-rudder-tab assembly were performed in the NACA 8-foot high-speed tunnel. Two cases of tab flutter were studied. It was shown conclusively that the frequency of the original or heavy tab was too low and caused coupling with one of the lower bending frequencies. A general conclusion was made that the tab frequency should be considerably higher than the lower modes of the fin-rudder assembly because there is generally a weaker coupling between the tab and the higher mode responses."

Report presenting 10 practical-construction models of sections of helicopter rotor blades tested in the NACA two-dimensional low-turbulence pressure tunnel at atmospheric pressure. Lift, drag, and pitching-moment characteristics of blades representing the present method of construction of the YR-4A helicopter were determined.

Report presenting two low-drag airfoils, the NACA 747A315 and the NACA 747A415, which are designed to have reduced pitching moments about the quarter-chord point and moderately high values of the design lift coefficient and are tested in the tow-dimensional low-turbulence pressure tunnel.

Report presenting a method for predicting from basic airplane characteristics the elevator deflection required to maintain optimum landing attitude. Charts for evaluating the components of the equation for elevator deflection and a comparison of computed and measured values for 15 airplanes are included. The computed deflection is considered the minimum value required to maintain landing attitude due to variations in piloting technique.

Report describing the behavior of the heat meter when it is used in thermal circuits which are under the influence of transient potentials. Three scenarios are considered: a heat meter suddenly placed on a hot surface, a heat meter mounted on the interior surface of the cabin wall of an uninsulated airplane climbing through air of decreasing temperature, and a heat meter mounted on the interior surface of the composite cabin wall of an airplane climbing through air of decreasing temperature.

Report presenting the effect of Reynolds number on the aerodynamic characteristics of a low-drag airfoil section tested under conditions of relatively high stream turbulence. The data are presented as curves of section angle of attack, section profile-drag coefficient, and section pitching-moment coefficient against section lift coefficient for various flap deflections.

Report presenting results of compression tests of six paper-base plastic panels with outward-acting normal pressure. All panels failed by separation of the skin, either from the rib or from the stiffeners. Results regarding the introduction of air pressure and types of failures encountered are provided.

Report presenting some principles for designing the optimum hull for a large long-range flying boat in order to suit the requirements of minimum drag, seaworthiness, and ability to take off and land at all operational gross weights. The principles include the use of moderate gross-load coefficients, ample forebody lengths, and deep steps and the close adherence of the form to that of a streamline body of revolution with a moderate fineness ratio.

"A technical method is given for calculating the axial interference velocity of a propeller. The method involves the use of certain weight functions P, Q, and F. Numerical values for the weight functions are given for two-blade, three-blade, and six-blade propellers" (p. 53).

Report presenting a description of a short method of estimating propeller efficiency for a given operating condition. The efficiency is determined for any design condition by evaluating separately from charts the induced losses and the profile-drag losses. The report covers single-rotating propellers of two, three, four, six, and eight blades and includes charts showing the rotational-energy loss for the given operating condition.

Report presenting a study to determine the effect of several methods of increasing the knock-limited power on critical cylinder temperatures. The knock-limited indicated horsepower and cylinder temperatures were determined for a Wright R-2600-8 cylinder under specified operating conditions. The most satisfactory method of increasing knock limited power was found to be internal cooling with water and the least satisfacotry was increasing the engine speed.

Report discusses the results of an investigation into the effectiveness of water injection into the combustion end zone of a spark-ignition engine cylinder for the suppression of knock. The injection angle was found to be very important for obtaining maximum results. The results of various angles and amounts of water were examined.

Report presenting simple curves by which the basic pressure-drop characteristics of unheated tubular radiators can be corrected to operating conditions in which the radiator is heated and in which the Mach number of the tube flow is of appreciable magnitude. The only data required for the use of the curves are the radiator dimensions, the rate of heat input, the pressure and temperature ahead of the radiator, and the rate of mass flow of air through the radiator.

Report details the methods of determining the heat-transfer rate, pressure drop, and drag power of high-altitude radiators. Performance charts are provided for a wide range of design variables.

"The high-speed photographic investigation of the mechanics of spark-ignition engine knock recorded in three previous reports has been extended with use of the NACA high-speed camera and combustion apparatus with a piezoelectric pressure pickup in the combustion chamber. The motion pictures of knocking combustion were taken at the rate of 40,000 frames per second. Existence of the preknock vibrations in the engine cylinder suggested in Technical Report no.727 has been definitely proved and the vibrations have been analyzed both in the high-speed motion pictures and the pressure traces" (p. 223).

From Summary: "The differential equation of Chaplygin's jet problem is utilized to give a systematic development of particular solutions of the hodograph flow equations, which extends the treatment of Chaplygin into the supersonic range and completes the set of particular solutions. The particular solutions serve to place on a reasonable basis the use of velocity correction formulas for the comparison of incompressible and compressible flows. It is shown that the geometric-mean type of velocity correction formula introduced in part I has significance as an over-all type of approximation in the subsonic range."

From Introduction: "The purpose of this analysis was to investigate the use of a function of intake-manifold pressure, exhaust back pressure, intake manifold temperature, and engine speed in place of a venturi as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."