Report presenting two low-drag airfoils, the NACA 747A315 and the NACA 747A415, which are designed to have reduced pitching moments about the quarter-chord point and moderately high values of the design lift coefficient and are tested in the tow-dimensional low-turbulence pressure tunnel.

From Introduction: "The purpose of this analysis was to investigate the use of function of intake-manifold temperature and pressure, exhaust back pressure, and engine speed in place of a ventri as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."

From Introduction: "The purpose of this analysis was to investigate the use of a function of intake-manifold pressure, exhaust back pressure, intake manifold temperature, and engine speed in place of a venturi as a means of measuring engine air consumption and to determine if this function is suitable for automatic mixture control."

Report presenting 10 practical-construction models of sections of helicopter rotor blades tested in the NACA two-dimensional low-turbulence pressure tunnel at atmospheric pressure. Lift, drag, and pitching-moment characteristics of blades representing the present method of construction of the YR-4A helicopter were determined.

From Introduction: "The lift increments of different flap arrangements were determined by the method of reference 1 with a simple chord correction factor being applied. This procedure is somewhat similar in basic principles to the method of reference 2. The accuracy of the present method was determined by calculating by means of this method the lift and moment increments of flaps on 10 different finite wing-flap combinations for which wind-tunnel data were available."

Note presenting an investigation of the effect of artificial aging on the strengths of driven rivets of the alloys used commercially for rivets: specifically, A17S-T, 17S-T, and 24S-T. The change in shear strength for each type of rivet after being exposed to artificial aging treatment of 10 hours at 375 degrees Fahrenheit applied to the driven rivets is described.

Report presenting a description of a short method of estimating propeller efficiency for a given operating condition. The efficiency is determined for any design condition by evaluating separately from charts the induced losses and the profile-drag losses. The report covers single-rotating propellers of two, three, four, six, and eight blades and includes charts showing the rotational-energy loss for the given operating condition.

Report presenting results of compression tests of six paper-base plastic panels with outward-acting normal pressure. All panels failed by separation of the skin, either from the rib or from the stiffeners. Results regarding the introduction of air pressure and types of failures encountered are provided.

Report presenting flight data, which shows that the absolute minimum or limit pressure coefficient on an airfoil is a function mainly of the Mach number for Mach numbers above about 0.3 and for usual flight values of the Reynolds number. The curve of limit pressure coefficient as a function of Mach number is established.

Report presenting some principles for designing the optimum hull for a large long-range flying boat in order to suit the requirements of minimum drag, seaworthiness, and ability to take off and land at all operational gross weights. The principles include the use of moderate gross-load coefficients, ample forebody lengths, and deep steps and the close adherence of the form to that of a streamline body of revolution with a moderate fineness ratio.

Report discusses an apparatus that may be used for indicating the formation of fatigue cracks or for following the progress of cracks. Details of the experiment and discussion of the way in which the deflection-crack area relationship may be used to monitor fatigue cracks are included.

Report presenting a convenient technical method to evaluate changes in the airfoil characteristics resulting from an extension of the chord at the trailing edge of a propeller blade section. The method determines the change in the angle of zero lift, the ideal angle of attack, and the difference in these angles as a function of the angle and length of the trailing-edge extension.

"Thirty-nine Z-sections formed from 24S-T aluminum-alloy sheet with the angle of bend between the flanges and the web varying from 5 degrees to 120 degrees were tested as columns. Angles of bend from 30 degrees to 120 degrees had little or no effect on the critical stress or on the average stress at maximum load for local instability of the columns. The lengths of the columns were such that at angles of bend below 30 degrees they failed by Euler buckling" (p. 1).

Report presenting an investigation to determine the effect of fuel volatility on engine power and economy as influenced by mixture distribution. Tests of four fuels of different volatility were conducted on a Wright R-2600-8 engine at desired cruising power, maximum cruising power, normal rated power, and takeoff power.

Report presenting a study to determine the effect of several methods of increasing the knock-limited power on critical cylinder temperatures. The knock-limited indicated horsepower and cylinder temperatures were determined for a Wright R-2600-8 cylinder under specified operating conditions. The most satisfactory method of increasing knock limited power was found to be internal cooling with water and the least satisfacotry was increasing the engine speed.

Report presenting an investigation conducted to determine the effect of water injection on the knock-limited performance of a V-type 12-cylinder liquid-cooled engine. The knock-limited performance tests were made at an engine speed of 3000 rpm with carburetor-air temperatures of 158, 101, and 50 degrees Fahrenheit at water-fuel ratios of 0, 0.2, 0.4, and 0.6.

Report presenting an analysis of the available data on the effects of trailing-edge modifications on the pitching-moment characteristics of airfoils. Some of the variables explored include the location of the airfoil aerodynamic center and variation of pitching-moment coefficient with control-surface deflection are provided.

Report discusses the results of an investigation into the effectiveness of water injection into the combustion end zone of a spark-ignition engine cylinder for the suppression of knock. The injection angle was found to be very important for obtaining maximum results. The results of various angles and amounts of water were examined.

Report presenting the fatigue data obtained at the Aluminum Research Laboratories from tests of various types of 17S-T and 53S-T specimens. The specimens were large enough to represent actual service conditions, but the repetition of loading was more rapid than would occur in ordinary service.

Report presenting a flight investigation made on a wing section of a P-47D airplane to determine the effect of roughness on wing profile drag with transition fixed far forward. Surveys of the wake were made for two surface conditions with transition fixed by a thread at 5 percent chord back of the leading edge on the upper and lower surfaces. Below the Mach number at which shock occurred, variations in Mach number of as much as 0.16 appeared to have no appreciable effect on the section profile-drag coefficients of either the smooth or roughened surfaces with transition fixed.

From Summary: "Tests on the B-34 fin-rudder-tab assembly were performed in the NACA 8-foot high-speed tunnel. Two cases of tab flutter were studied. It was shown conclusively that the frequency of the original or heavy tab was too low and caused coupling with one of the lower bending frequencies. A general conclusion was made that the tab frequency should be considerably higher than the lower modes of the fin-rudder assembly because there is generally a weaker coupling between the tab and the higher mode responses."

Report presenting an investigation conducted on the foaming characteristics of representative aircraft-engine lubricants in order to arrive at an adequate theory of the foaming of such oils. Methods of measuring foaming are compared and analyzed for their significant factors.

Report presenting a paper in a series about the cooling of aircraft-engine installations with special reference to the difficulties of cooling at high altitudes. This particular paper discusses the properties of NACA standard air and Army summer air, with corresponding stagnation conditions for a range of flight speed, as summarized in tables and figures.

Report presenting the heat-transfer theory for air-cooled engines and an analysis of the cooling pressure drop for the case in which the pressure drop is an appreciable fraction of the absolute pressure. A chart is given for the simple determination of the cooling pressure drop predicted on the basis of the usual type of sea-level cooling-correlation tests.