"Knock-limited performance data were obtained for three fuels on an R-1830-75 engine in a B-24D airplane at engine speeds of 1800, 2250, and 2600 rpm, a spark advance of 25 degrees B.T.C., and carburetor-air temperatures of 85 F for 1800 and 2250 rpm and 100 F for 2600 rpm. The test fuels were a blend of 80 percent 28-R plus 20 percent triptane (leaded to 4.5 ml TEL/gal), a blend of 80 percent 28-R plus 15 percent toluene (leaded to 4.5 ml TEL / gal), and 28-R fuel. The knock-limited manifold pressure of the toluene blend depreciated more in the lean region than the triptane blend or 28-R fuel" (p. 1).

From Introduction: "The purpose of the present paper is to show in more detail the possibilities end the limitations of the use of regeneration as a means of effecting greater fuel economy and of reducing the net weight of the power plant and fuel of compressor-turbine-propeller aircraft engines."

An investigation was conducted to determine the effects of three design modifications of the original NACA injection impeller on the performance of an R-3350 engine. Different methods of injecting the fuel into the impeller air stream were studied and evaluated from the individual cylinder fuel-air ratios and the resulting cylinder temperatures. Each impeller was tested for a range of engine powers normally used in flight operation. The relatively simple design of the original injection impeller produced approximately the same mixture- and temperature-distribution characteristics as the modified impellers of more complex design. None of the modifications appreciably affected the manifold pressure, the combustion-air flow, nor the throttle angle required to maintain a given engine power,.

"The results obtained from an evaluation for gust and draft velocities of acceleration and airspeed-altitude records taken by NACA recording instruments installed in P-61c airplanes participating in thunderstorm flights 6, 7, and 8 of July 9, 1946, July 10, 1946, and July 11, 1946, respectively, are presented herein. These data are summarized in tables I and II. In accordance with a recent discussion with a member of the U.S. Weather Bureau staff, the tabulated results for the present flight include in addition to data of the type presented in reference 1, the initial heading of the airplane for each traverse, the pressure altitude at the start of each traverse in increments of 500 feet, and the gust gradient distance when it could be evaluated" (p. 1).

From Introduction: "Performance results of the tail-pipe burning investigation on the TG-180 turbojet engine and a comparison of experimental results with theoretical calculations are presented."

"Tests were performed on a partial span of the wing of a McDonnell XFD-1 airplane to determine a combination of sealed internal balance and spring-tab stiffness for the aileron that would give satisfactory stick-force characteristics for the airplane. Two sealed internal balances were tested in combination with spring tabs of various stiffnesses. One of the combinations was tested at several speeds to determine the variation of stick force with speed" (p. 1).

:Spin tests have been performed in the Langley 20-foot free-spinning tunnel on a 1/18-scale model of the Fairchild XNQ-1 airplane. The spin and recovery characteristics of the model were determined for the normal gross-weight loading and for two variations from this loading - center of gravity moved rearward and relative mass distribution increased along the fuselage. These tests were performed for two vertical-tail plan forms. The investigation also included simulated pilot-escape tests and rudder-force tests" (p. 1).

"By use of the methods of thin airfoil theory, which include effects of compressibility, relations are developed which permit the rapid determination of the pressure distribution over an unstaggered cascade of airfoils of a given profile, and the determination of the profile shape necessary to yield a given pressure distribution for small chord gap ratios. For incompressible flow the results of the theory are compared with available examples obtained by the more exact method of conformal transformation. Although the theory is developed for small chord/gap ratios, these comparisons show that it may be extended to chord/gap ratios of order unity, at least for low speed flows" (p. 1).

"An investigation of the spin and recovery characteristics of a 1/24-scale model of the McDonnell XP-88 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect and inverted spin and recovery characteristics of the model in the normal loading were determined. Tests of the model in the long-range loading also were made" (p. 1).

"An analysis of the effects of compressibility on the longitudinal stability, control, and trim of airplanes flying at high subsonic speeds and a discussion of the causes of and the means for lessening or preventing the diving tendency are presented. Wind-tunnel results for Mach numbers up to 0.90 are included for purposes of illustration and cover several investigations of longitudinal stability and control, airfoil characteristics, dive-recovery aids, and elevator characteristics. Methods are indicated for compensating for the undesirable control tendencies results from the characteristics of the wing at supercritical speeds by the appropriate choice of elevator contour" (p. 1).

From Summary: "Wind-tunnel tests were made of a 1/25 scale model of the Martin JRM-1 airplane to determine: (1) The longitudinal stability and control characteristics of the JRM-1 model near the water and lateral and directional stability characteristics with power while moving on the surface of the water, the latter being useful for the design of tip floats; (2) The stability and stalling characteristics of the wing with a modified airfoil contour; (3) Stability characteristics of a hull of larger design gross weight; The test results indicated that the elevator was powerful enough to trim the original model in a landing configuration at any lift coefficient within the specified range of centers of gravity."

Report presenting a flight investigation conducted to establish the heat requirements for ice prevention on aircraft windshields mounted on the forebody of an airplane at several angles. Electrically heated windshields were used in order to provide accurate measuring of heat input to the windshield. Results regarding the quantity of heat provided, amount of water collection, ideal windshield angle, ranges in airplane velocity, and icing conditions are provided.

From Summary: "The results of numerous unrelated tests of dive-recovery flaps are collected in this report and presented in a form suitable for use in the preliminary design of dive-recovery flap installations. Since the data were obtained for airplane models of quite widely varying configurations, and are limited largely to a Mach number of 0.80, it is recommended that each new installation be carefully flight-tested before final approval. A flight-test procedure is outlined which will insure a maximum degree of safety."

"The problems associated with propeller noise and with the design of propellers that are less noisy than those conventionally used are presented. Three aspects of these problems are discussed: acoustical, aerodynamic, and structural. Some of the factors which must be considered in the design of a quiet propeller are outlined" (p. 1).

From Summary: "An investigation has been conducted on a V-1650-7 engine to determine the cylinder temperatures and the coolant and oil heat rejections over a range of coolant flows (50 to 200 gal/min) and oil inlet temperatures (160 to 2150 F) for two values of coolant outlet temperature (250 deg and 275 F) at each of four power conditions ranging from approximately 1100 to 2000 brake horsepower. Data were obtained for several values of block-outlet pressure at each of the two coolant outlet temperatures. A mixture of 30 percent by volume of ethylene glycol and 70-percent water was used as the coolant."

A 1/5.5-size powered dynamic model of the Columbia XJL-1 amphibian was landed in Langley tank no. 1 in smooth water and in oncoming waves of heights from 2.1 feet to 6.4 feet (full-size) and lengths from 50 feet to 264 feet (full-size). The motions and the vertical accelerations of the model were continuously recorded. The greatest vertical acceleration measured during the smooth-water landings was 3.1g.

From Introduction: "This report presents an analysis based on flight and wind-tunnel test data directed toward the determination of the probable cause of the pitch-up. Wing pressure distribution and stability and control characteristics in the dive are also included."

Memorandum presenting an investigation of thrust augmentation by the injection of water-alcohol mixtures into the compressor inlets of a turbojet engine with a centrifugal-flow-type compressor at altitudes of sea level, 5000 feet, and 10,000 feet. The investigation was made to determine the water-alcohol mixture and the injection rate for optimum thrust augmentation. At a standard NACA altitude of 10,000 feet and an engine speed of 16,000 rpm, the mixture and injection rate for optimum thrust augmentation was found to be 20-percent alcohol to water by weight injected at a rate of approximately 1.45 pounds per second.

From Summary: "An investigation was made by the NACA wing-flow method to determine the longitudinal stability and control characteristics at transonic speeds of a semispan model of the XF7U-1 tailless airplane. The 25-percent chord line of the wing of the model was swept back 35 deg. The airfoil sections of the wing perpendicular to the 25-percent chord line were 12 percent thick. Measurements were made of the normal force and pitching moment through an angle-of-attack range from about -3 deg to 14 deg for several ailavator deflections at Mach numbers from 0.65 to about 1.08."

Report presenting annular air inlets situated several diameters behind the apex of various bodies of revolution tested over the range of Mach numbers between 1.36 and 2.01 to determine the effects of relatively thick boundary layers on the characteristics of duct entrances in supersonic flight. Results regarding the presentation of data, precision, and general flow characteristics are provided.

"An investigation has been conducted in the Langley 20-foot free- spinning tunnel scale model of the Cornelius XFG-1 glider, a tailless design having its wings swept forward 15 degrees. It was previously found to possess erratic spin and recovery characteristics, and tests were made to determine modifications which would lead to normal steady spins with consistently good recoveries. The results of the investigation indicated that modifications that aid not appreciably alter the basic design aid not appreciably improve the spin and recovery characteristics" (p. 1).

Report presenting an investigation of the closed wind-tunnel phenomenon of choking and the wall-constriction effects in the subsonic Mach number range where supersonic Mach numbers appear using the hydraulic analogy. Application of the results to wind tunnel testing, the subsonic choking phenomena, and effects of the walls are described.

From Introduction: "This paper presents the test data obtained for the NACA 10-(3) (08)-03R propeller blade which was one of the blades tested to determine the effects of shank design."

"Results are presented of an investigation in the Langley 19-foot pressure tunnel of the longitudinal characteristics of a semispan model wing having 37 degrees sweepback of the leading edge, an aspect ratio of 6, and NACA 641-212 airfoil section perpendicular to the 27-percent-chord line. Several types of stall-control devices including extensible round-nose leading-edge flaps, a leading-edge slat, and a drooped leading edge were investigated; partial- and full-span trailing-edge split and double slotted flaps were also tested. In addition, various combinations of the aforementioned leading- and trailing-edge flaps were investigated" (p. 1).