"An investigation was conducted to determine the longitudinal- and lateral-stability characteristics of a 0.5-scale model of the Fairchild Lark missile. The model was tested with 0 deg and with 22.5 deg of roll. Three horizontal wings having NACA 16-009, 16-209, and 64A-209 sections were tested. Pressures were measured on both pointed and blunt noses" (p. 1).

From Summary: "An investigation has been conducted with the Langley helicopter tower to obtain basic performance and control characteristics of the Raman rotor system. Blade-pitch control is obtained in this configuration by utilizing an auxiliary flap to twist the blades. Rotor thrust and power required were measured for the hovering condition and over a range of wind velocities from 0 to 30 miles per hour. The control characteristics and the transient response of the rotor to various control movements were also measured."

Report presenting the results of a wind-tunnel investigation of the low-speed aerodynamic characteristics of a 45 degree sweptback horizontal-tail model of aspect ratio 2 and a comparison of these results with results for a model of the same aspect ratio with an unswept hinge line. Results regarding the lift and hinge-moment parameters, static longitudinal stability, effect of Reynolds number, effect of standard roughness, effect of removing elevator nose seal, and visualization of the air flow are provided.

Report presenting the results of a wind-tunnel investigation of the effects of variation of trailing-edge angle and leading-edge radius on the aerodynamic characteristics of a 10-percent-chord-thick airfoil section at a range of Mach numbers.

Report presenting an altitude-chamber investigation to determine the altitude performance characteristics of the British Rolls-Royce Nene II turbojet engine with a standard 18.75-inch-diameter jet nozzle. Results regarding the simulated flight performance and generalized performance across other altitude and pressure characteristics are provided.

"Measurements were made, in dives to transonic speeds, of the static-pressure position error at a distance of one chord ahead of the McDonnell XF-88 airplane. The airplane incorporates a wing which is swept back 35 deg along the 0.22 chord line and utilizes a 65-series airfoil with a 9-percent-thick section perpendicular to the 0.25-chord line. The section in the stream direction is approximately 8-percent thick. Data up to a Mach number of about 0.97 were obtained within an airplane normal-force-coefficient range from about 0.05 to about 0.68" (p. 1).

Report presenting free-flight investigations conducted on four 16-inch-diameter ramjet units to determine the performance at high subsonic and supersonic velocities. Data for evaluating the performance were obtained from radio-telemetering and radar-tracking equipment. Results regarding combustion performance, diffuser total-pressure recovery, thrust coefficient, and external drag coefficient are provided.

Memorandum presenting flight tests with a fighter airplane to study the effect of boundary-layer suction aft of the shock wave on airfoil drag at supercritical Mach numbers and high Reynolds numbers. Airfoil chord force was determined from pressure-distribution measurements obtained at a range of Mach numbers at steady dives. Results of the tests showed no measurable effect of suction for the suction coefficient available.

Report presenting a low-speed wind-tunnel investigation to determine the lateral control characteristics of extensible wing-tip ailerons on an untapered semispan wing with two configurations; one was unswept and had an aspect ratio of 3.13 and the other was swept back 45 degrees and had an aspect ratio of 1.59. Results regarding the plain-wing aerodynamic characteristics and lateral control characteristics are provided.

Report presenting measured pressure over airfoils at Mach number 1, with subsonic velocities at the nose and supersonic velocities throughout the rear portion, are analyzed by comparison with calculations for similar cases. Results regarding the theoretical basis of approximation, comparison of Prandtl-Meyer flow with measurements, comparison of linear-velocity extrapolation with measurements, and effect of boundary layer upon airfoil pressures are provided.

Report presenting an investigation conducted to determine the effects of increased gas temperatures on the performance of cast Vitallium blades in a turbojet engine. Results regarding the experimental investigation and metallurgical investigation are provided.

Report presenting an investigation of the operation of two submerged-type inlets in a wind tunnel at subsonic and transonic speeds. The pressure recovery was relatively constant throughout the lower subsonic speed range. The ability of the divergent-walled inlet to operate with satisfactory pressure recovery at higher free-stream Mach numbers than was possible with the parallel-walled inlet is attributed to the difference in the boundary-layer characteristics of the two types of inlets.

Report presenting surveys of the flow of the asymmetric adjustable nozzle of the 6- by 6-foot supersonic wind tunnel, which were made to determine the uniformity of the air stream. Test techniques for minimizing the effects of stream irregularities and the results of force and pressure-distribution tests of a swept-wing model are presented to illustrate the effectiveness of these techniques.

Investigation conducted in the altitude wind tunnel to study the effect of Reynolds number on the performance of an axial-flow compressor. The compressor was operated as a part of a turbojet engine over a range of pressure altitudes and compressor-inlet Reynolds numbers. Results regarding compressor efficiency, air flow, and a comparison with axial-flow compressors of different design are provided.

Report presenting the pressure distribution over a highly swept wing at supersonic speeds to provide data for a comparison of measured and predicted loadings. The wing for this investigation had 63 degrees of sweepback of the leading edge, an aspect ratio of 3.5, and a taper ratio of 0.25. Over the regions influenced by the wing tip and trailing edge, the effects of viscosity apparently are responsible for the poorer agreement between theory and experiment.

"Four 90 degree two-dimensional turning passages designed by the method of characteristics were tested at an inlet Mach number of 1.71. The measured losses varied from 5 to 15 percent of the inlet stagnation pressure. The smallest loss was obtained for a passage in which separation on the convex surface was minimized through the introduction of a favorable pressure gradient" (p. 1).

Report presenting an analysis of the effects of compressibility on the pressure coefficients of several bodies of revolution by comparing experimentally determined pressure coefficients with corresponding pressure coefficients calculated by the use of linearized equations of compressible flow. The results indicated that the theoretical methods predict the subsonic pressure-coefficient changes over the central portion of the body but do not predict the pressure-coefficient changes near the nose.

Report presenting the hydrodynamic characteristics of a swept planing-tail hull as determined by water tank testing. The hull shape was based on results from previous testing indicating that symmetrical airfoil sections and slender boom-like afterbodies lower the drag. Results regarding spray characteristics, take-off stability and trims, landing stability, resistance, and directional stability are presented.

Report presenting a supersonic compressor design with supersonic velocity at the entrance of the stator on the assumption of two-dimensional flow. The rotor and stator losses assumed in the analysis are based on the results of preliminary supersonic cascade tests. The starting conditions and stability of the flow in rotor and stator are discussed, and the desirability of the variable-geometry stators and adjustable guide vanes is indicated.

"A supersonic compressor design having supersonic velocity at the entrance of the stator is analyzed on the assumption of two-dimensional flow. The rotor and stator losses assumed in the analysis are based on the results of preliminary supersonic cascade tests. The results of the analysis show that compression ratios per stage of 6 to 10 can be obtained with adiabatic efficiency between 70 and 80 percent. Consideration is also given in the analysis to the starting, stability, and range of efficient performance of this type of compressor" (p. 1).

Report presenting an investigation in the high-speed 7- by 10-foot tunnel to determine the high-subsonic aerodynamic characteristics of three different types of flying-boat hull: a planing-tail hull, a blended hull, and an airfoil-forebody swept hull.

Report discussing an investigation of the aerodynamic characteristics of an airfoil-forebody swept flying boat hull with a wing and tail swept back 51.3 degrees at the leading edge. The swept hull's minimum drag coefficient was about the same as the parent model or streamline model. Various combinations of flaps were also utilized.

Report presenting a wind-tunnel investigation to determine the effect of propeller operation on the characteristics of submerged inlets. The tests were performed with a model of a hypothetical fighter airplane powered by a turbine-propeller unit. The propeller had eight blades with thin airfoil shanks and dual rotation and the submerged inlets were placed in the fuselage behind the propeller and forward of the wing.

From Summary: "A single-stage modification of the turbine from a Mark 25 torpedo power plant was investigated to determine the performance with two nozzles and three rotor-blade designs. The performance was evaluated in terms of brake, rotor, and blade efficiencies at pressure ratios of 8, 15 (design), and 20. The blade efficiencies with the two nozzles are compared with those obtained with four other nozzles previously investigated with the same three rotor-blade designs."