Form 843 Claim for tax assessed by Texas Cotton Industries.

Data complied regarding wells and other water resources, including water quality analysis, measurements, and other relevant information.

Report presents the results of a study made of the effects of known end restraint on commercially available round and streamline tubing of chromium-molybdenum steel, duralumin, stainless steel, and heat-treated chromium-molybdenum steel; and a more accurate method than any previously available, but still a practical method, was developed for designing compression members in riveted or welded structures, particularly aircraft. Two hundred specimens were tested as short, medium-length, and long columns with freely supported ends or elastically restrained ends. Tensile and compressive tests were made on each piece of original tubing from which column specimens were cut.

This report presents the results of an investigation conducted to determine the interrelation of the constituents of the exhaust gases of internal-combustion engines and the effect of engine performance on these relations. Six single-cylinder, liquid-cooled tests engines and one 9-cylinder radial air-cooled engine were tested. Various types of combustion chambers were used and the engines were operated at compression ratios from 5.1 to 7.0 using spark ignition and from 13.5 to 15.6 using compression ignition. The investigation covered a range of engine speeds from 1,500 to 2,100 r.p.m.

Circular describing the Airspeed A.S. 10 "Oxford", which is a twin-engine trainer with a variety of equipment, including propellers, landing gear, and other components.Details of the wings, fuselage, the inside, characteristics, performance, drawings, and photographs are provided.

"Charts are presented for checking the stability of plane systems of rods, the use of the charts being illustrated by examples. It is also indicated how best to combine the individual members to form stable structures" (p. 1).

Note presenting a discrepancy between the predicted and actual point of transition from laminar to turbulent boundary layer that had been found. This effect may be due to the comparatively small radius of curvature of the upper surface of the wing.

"In the flow over the upper surface of a wing, a discrepancy between the predicted and actual point of transition from laminar to turbulent boundary layer was found. This effect may be due to the comparatively small radius of curvature of the upper surface of the wing. Tests were undertaken to investigate this effect. As far as the authors know, the present investigation is the first to show that curvature has a pronounced effect on the transition of the boundary layer from the laminar to the turbulent state" (p. 1).

From Summary: "Results are presented of the drag tests of six bodies of revolution with systematically varying shapes and with a fineness ratio of 5. The forms were derived from source-sink distributions, and formulas are presented for the calculation of the pressure distribution of the forms. The tests were made in the N.A.C.A. variable-density tunnel over a range of values of Reynolds number from about 1,500,000 to 25,000,000. The results show that the bodies with the sharper noses and tails have the lowest drag coefficients, even when the drag coefficients are based on the two-thirds power of the volume. The data shows the most important single characteristic of the body form to be the tail angle, which must be fine to obtain low drag."

"An airplane in steady rectilinear flight was assumed to experience an initial disturbance in rolling or yawing velocity. The equations of motion were solved to see if it was possible to hasten recovery of a stable airplane or to secure recovery of an unstable airplane by the application of a single lateral control following an exponential law. The sample computations indicate that, for initial disturbances complex in character, it would be difficult to secure correlation with any type of exponential control" (p. 1).

An investigation was made to determine the spinning characteristics of Clark Y monoplane wings with different plan forms. A rectangular wing and a wing tapered 5:2, both with rounded tips, were tested on the N.A.C.A. spinning balance in the 5-foot vertical wind tunnel. The aerodynamic characteristics of the models and a prediction of the angles of sideslip for steady spins are given. Also included is an estimate of the yawning moment that must be furnished by the parts of the airplane to balance the inertia couples and wing yawing moment for spinning equilibrium. The effects on the spin of changes in plan form and of variations of some of the important parameters are discussed and the results are compared with those for a rectangular wing with square tips. It is concluded that for a conventional monoplane using Clark Y wing the sideslip will be algebraically larger for the wing with the rounded tip than for the wing with the square tip and will be largest for the tapered wing. The effect of plan form on the spin will vary with the type of airplane; and the provision of a yawing-moment coefficient of -0.025 (i.e., opposing the spin) by the tail, …

In many installations of castering rubber-tired wheels there is a tendency for the wheel to oscillate violently about the spindle axis. This phenomenon, popularly called 'shimmy,' has occurred in some airplane tail wheels and has been corrected in two ways: first by the application of friction in the spindles of the tail wheels; and, second, by locking the wheels while taxiing at high speeds. Shimmy is common with the large wheels used as nose wheels in tricycle landing gears and, since it is impossible to lock the wheels, friction in the nose-wheel spindle has been the sole means of correction.

"The monocoque form of airplane construction has introduced a number of new problems to the stress calculator and the designer. The problems for the stress calculator fall into two groups: the determination of the stress condition (shell statics) and the determination of the failing strength (shell strength). The present report summarizes the most important theoretical and experimental results on this subject" (p. 1).