Report discussing the results of an investigation to determine the low-speed power-off stability and control characteristics of a model of the Bell D-188A VTOL airplane. The static stability and control characteristics were generally satisfactory except above certain angles of attack and aileron effectiveness dropped off as the angle of attack was increased. Modifications for increasing the directional stability by altering the vertical tails are also described.

Report presenting an investigation in the transonic pressure tunnel to determine the afterbody pressure distribution and fin loading characteristics of two configurations of the TX-21 special weapon. The only different in the two configurations was the nose contour, with one having a hemispherical-flat shape and one with a double-radius ogive-flat shape. Results regarding the pressure port, fin loads, and force measurements are provided.

A series of 11 fuels ranging in volatility and including various types of hydrocarbons were tested in a single tubular combustion chamber of a turbojet engine under inlet-air conditions simulating engine operation at two speeds at an altitude of 40,000 feet. Temperature-rise data at various fuel-air ratios were obtained for each set of air-flow conditions. Results regarding the effect of combustor inlet-air conditions on temperature rise, four different series of tests, and a review of some general considerations are provided.

Report presenting the results of an experimental investigation to determine the pressure-recovery and mass-flow characteristics of single and twin NACA submerged intakes on the sides of a fuselage at various angles of sideslip. Tests were conducted with single and twin submerged intakes on a model of a fighter-type airplane.

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel at Mach number 2.01 to determine the effects of sweep angle and thickness ratio on the static lateral stability characteristics of a series of wings with taper ratio 0.2 and aspect ratio 3.5. The results are presented with little analysis.

"Available experimental two-dimensional-cascade data for conventional compressor blade sections are correlated. The two-dimensional cascade and some of the principal aerodynamic factors involved in its operation are first briefly described. Then the data are analyzed by examining the variation of cascade performance at a reference incidence angle in the region of minimum loss" (p. 1).

Report detailing an investigation of the aerodynamic characteristics of a wing-propeller combination with the propeller rotating in the wing-chord plane of a two-dimensional wing. Total static lift was measured with and without the wing for a 3-foot-diameter propeller, while the effects of a ground plane on the static lift of the wing-propeller combination were measured with a 2-foot-diameter propeller. Results regarding static testing, forward speed tests, and propeller loads are provided.

Report presenting testing of a five-stage rocket-propelled model flown to a Mach number of 15.5 and an altitude of 98,200 feet. Temperatures were measured at six stations along the inside surface of the blunted conical nose with a total angle of 29 degrees. Experimental and theoretical values were similar at the first temperature measuring station, but the experimental results became increasingly greater than the theoretical values at rearward measuring stations.

Report presenting an investigation of transpiration cooling in a preflight jet model consisting of a double wedge of 40 degrees included angle with a porous stainless-steel specimen inserted flush with the top surface of the wedge. Nitrogen and helium were used as coolants and testing was conducted for flow rates ranging from about 0.03 to 0.30 percent of the local weight flow. The helium coolant required only about one-fourth to one-fifth the coolant flow weight as the nitrogen coolant for the same amount of heat-transfer reduction.

Report presenting a free-flight investigation of the zero-lift rolling effectiveness of air-jet spoilers on an unswept flexible wing over a range of Mach numbers. Testing was made to determine the relative effectiveness of air-jet spoilers at leading-edge and trailing-edge locations. The leading-edge jet spoiler exhibited near-zero effectiveness at transonic speeds and had a roll reversal between Mach numbers 0.93 and 1.35.

Compendium presenting a comprehensive integration of available aerodynamic design information on axial-flow compressors. The subjects of the first volume of this investigation are objectives and scope, compressor design requirements, compressor design system, potential flow in two-dimensional cascades, and viscous flow in two-dimensional cascades.

Chapters XI to XIII concern the unsteady compressor operation arising when compressor blade elements stall. The fields of compressor stall and surge are reviewed in Chapters XI and XII, respectively. The part-speed operating problem in high-pressure-ratio multistage axial-flow compressors is analyzed in Chapter XIII. Chapter XIV summarizes design methods and theories that extend beyond the simplified two-dimensional approach used previously in the report. Chapter XV extends this three-dimensional treatment by summarizing the literature on secondary flows and boundary layer effects. Charts for determining the effects of errors in design parameters and experimental measurements on compressor performance are given in Chapters XVI. Chapter XVII reviews existing literature on compressor and turbine matching techniques.