Analysis was made to determine characteristics required of a balancing-tab system for ailerons in order to reduce aileron stick forces to any desired magnitude. Series of calculations based on section data were made to determine balancing-tab systems of various chord tabs and ailerons that will give, for a particular airplane, zero rate of aileron hinge moment with aileron deflection and yet will produce same maximum rate of roll as a plain unbalanced 15-percent chord aileron of same span. Effects of rolling velocity and of forces in tab link on aileron hinge moments have been included.

Two airfoil plans were used for propeller blades. One is modified Clark Y section designed for structural reliability and the second an NACA 16 airfoil section designed to produce minimum aerodynamic losses. At low air speeds, the propeller designed for aerodynamic effects showed a gain of from 1.5 to 4.0 percent in propulsive efficiency over the conventional type depending on the pitch. Because of the numerous variables involved, the effect of each one on the aerodynamic characteristics of the propellers could not be isolated.

Report presenting testing of a Pratt & Whitney R-1830-43 engine mounted in a B-24D nacelle in the full-scale wind tunnel in order to investigation the potential improvements of fuel economy. Suggestions for improving the cruising power and cruising range by operating at specified fuel-air ratios are provided.

Report presenting tests conducted with an air-cooled cylinder on two fuels rated at approximately 100-octane number by the C.F.R. aviation method with and without a 40-percent addition of an aromatic mixture. The aromatic mixture consisted of 50 percent toluene, 37.5 percent xylene, and 12.5 percent benzene. Results regarding engine performance and engine temperature are provided.

Report presenting an investigation in the 20-foot propeller-research tunnel to determine the effect of variations in angle of pitch on the aerodynamic characteristics of several propeller combinations. The combinations investigated included two-, three-, four-, and six-blade single-rotating propellers and a six-blade dual-rotating propeller on a nacelle with four angles of thrust axis. The propulsive efficiency was found to decrease as the angle of pitch increased.

Report presenting an exploration of fatigue stresses of some wrought aluminum alloys, including charts that cover different ranges of stress and number of cycles.

Investigations were undertaken to improve the ailerons of a P-51 fighter so as to obtain greater effectiveness without increasing the stick forces. Modifications consisted of increasing the deflection range of the aileron to 70 percent and changing the original concave section to a thick section with beveled trailing edge. Results of the modified ailerons showed an increase in effectiveness over the original aileron of 70 percent at low speed and 55 percent at high speeds.

Report presenting testing of a model of the Douglas DC-3 airplane for several loading conditions. The load factor for the complete airplane, for the horizontal tail, and the force to start moving the elevator downward were estimated for some steady spins. Testing occurred at 2500 feet and 10,000 feet.

Bulletin presenting a discussion of information as to the influence on spins and spin recovery of the wing loading and load distribution of present-day pursuit airplanes. The high wing loadings results in high rates of descent and large control forces for recovery.

Bulletin presenting a study of several airfoils, including a conventional NACA 23021 and some low-drag airfoils for which the thickness had been increased, as smooth airfoils and after the application of a standard roughness. The results show some of the airfoils to be critical to separation resulting from such flow disturbances.

Report presenting an analysis of the failure of adhesive bonds and its relation to boundary stress concentrations. A variety of material combinations, including metals and plastics, were examined and stress tested. The method of computing the thermal coefficients is applied to mixtures and especially to reinforced plastics.

Report presenting the results of nearly 200 tests made on the strength of shear webs of 24S-T aluminum alloy, with and without lightening holes. The tests were made in a jig of the single-specimen type, in which the specimen is free to collapse completely without developing diagonal tension. Results regarding the strength of the shear webs, stiffness of shear webs, and permanent-set tests are provided.

"The calculation of the stresses around cut-outs is discussed on the basis of a simplified application of the shear-lag theory previously published. Experimental stringer strains were measured around a systematic series of cut-outs. The test results indicate that the proposed method of calculating the stringer stresses is acceptable as a basis for stress analysis" (p. 1).

Report presenting an approximate method of applying the available data on various types of flaps in the design of fighter brakes together with several examples of its use. The computed effects of flap type, size, location, and deflection as well as the effects of altitude and initial velocities on braking characteristics are also shown in some examples using the method to determine various flap arrangements.

Bulletin presenting the results of an investigation to determine possible improvements in the tightness and the flushness of machine-countersunk rivets. Specimens used in the study were simple lap joints made by different riveting methods. The results indicate that a comparison of the quality of machine-countersunk riveted joints on the basis of maximum load alone is not justified.

Report presenting testing in the two-dimensional tunnel of four models submitted by the Glenn L. Martin Company as intermediate sections of the wing of the XB-33 airplane. Each airfoil model had different types of flaps or no flaps at all. Results regarding the lift and drag data, lift coefficients, effect of flap positions, aileron effects, drag coefficients, and hinge-moment coefficients are provided.

Report presenting a summary of published information on braking friction coefficients. Analysis indicates that the magnitude of the friction coefficient available will affect the technique required for obtaining the shortest ground run only under extreme conditions.

Report presenting force-test measurements in two-dimensional flow in the 4- by 6-foot vertical tunnel of the characteristics of an NACA 0015 airfoil equipped with a plain flap with a chord 30 percent of the airfoil chord and a plain tab with a chord 20 percent of the flap chord. Results regarding lift, hinge moment of flap, pitching moment, drag, and tab characteristics are provided.