"Several methods of cyclic de-icing of a gas-heated airfoil were investigated to determine ice-removal characteristics and heating requirements. The cyclic de-icing system with a spanwise ice-free parting strip in the stagnation region and a constant-temperature gas-supply duct gave the quickest and most reliable ice removal. Heating requirements for the several methods of cyclic de-icing are compared, and the savings over continuous ice prevention are shown. Data are presented to show the relation of surface temperature, rate of surface heating, and heating time to the removal of ice" (p. 1).

Report presenting an investigation of some effects of aileron spanwise location and wing structural rigidity on the rolling power of 0.3-chord plain, flap-type ailerons on a wing with a taper ratio of 0.25, an aspect ratio of 3.5, and swept back 63 degrees at the leading edge. Results regarding the aeroelastic effects and aileron span and spanwise location are provided.

Report presenting measurements of wing and fuselage pressure distributions made at low and high subsonic Mach numbers on a scale model of the projected X-3 research airplane. Tests were conducted in pitch and yaw and included measurements of the total pressure in the fuselage boundary layer at the location of the left boundary-layer bleed scoop.

Report presenting propeller-blade torsional-deflection data obtained during an investigation of the pressure distribution on constant-chord solid aluminum-alloy blades differing only in camber and thickness. Testing indicated that thinner blades were able to produce greater amounts of deflection. Results regarding torsional deflections are also provided.

Report presenting results from a limited flight program to obtain information on airplane response and actual rates and amounts of control motion used by service pilot in performance of squadron operational training. Results regarding control deflection, control rates, airplane angular velocities, airplane angular accelerations, angle of attack and angle of sideslip, airplane load factors, and airspeed and altitude are provided.

"During the flight investigation of the X-1 airplane the hinge moments of the elevator and aileron control surfaces have been measured over a Mach number range extending to above 1.0. The results of these measurements are presented in this paper" (p. 2).

Investigation of the effect on zero-lift drag of varying the size and number of symmetrically mounted nacelles on a 45 degree sweptback wing and body combination as determined by free-flight tests of rocket-propelled models over a range of Mach and Reynolds numbers. The nacelle configuration consisted of a twin-engine nacelle near the fuselage, a combination of single-engine nacelles at the wing tip and fuselage, a large nacelle at the wing tip, and a large nacelle near the fuselage.

Report presenting pressure-drag coefficients and the changes in these coefficients with mass-flow ratio, which have been measured in tests of six open-nose conical cowls at an angle of attack of 0 degrees. Testing occurred in the Ames 8 by 8-inch supersonic wind tunnel at a range of Mach numbers. Results regarding pressure distributions, change in cowl pressure drag with mass-flow ratio, cowl pressure drag at a given mass-flow ratio, and changes in cowl pressure drag with mass-flow ratio as a function of Mach number are provided.

Report presenting the zero-lift drag of several wings obtained at supersonic Mach numbers in free flight with rocket-propelled models. The wings tested all had the same exposed area, mounted on the same basic body configuration, and had one of four different types of wings.

Memorandum presenting an investigation to devise an air-cooled turbine blade which eliminated the difficulties encountered with brazing in air-cooled-blade fabrication. Techniques were developed for casting air-cooled blades with a large number of relatively small cooling passages near the airfoil surface; two such blades of HS-21 material were operated in a turbojet engine modified for air cooling. Results regarding the heat-transfer characteristics, stress and durability results, and evaluation of cast-cored-blade potential are provided.

From Introduction: "This report investigates some of the problems involved in scheduling the tailpipe temperature to avoid stall during acceleration. The object of this report is to investigate the dynamics of a closed-loop acceleration control that follows a schedule of tailpipe temperature with rotor speed."

Report discusses the results of an investigation of a model of a wing of 45 degree sweepback and aspect ratio 6 to determine the aerodynamic characteristics and suction requirements for boundary-layer control by means of area suction applied to trailing-edge flaps. Various flap spans and flap deflections were tested. The measured values of the coefficients were compared to the calculated values.

Report presenting the tendencies of 14 different fuels and three fuel blends to produce high-frequency oscillatory combustion (screaming) in a 200-pound-thrust, water-cooled, liquid-oxygen-fuel rocket engine. The fuels, in order of increasing screaming tendency, were hydrazines, branched-chain paraffins, aromatics, and amines, and straight-chain paraffins. Results regarding screaming tendency and screaming amplitude are provided.

"An experimental investigation has been conducted to determine the stability and control characteristics of a 0.13-scale free-flight model of the Convair XFY-1 airplane during take-offs and landings in steady winds. The tests indicated that take-offs in headwinds up to at least 20 knots (full scale) will be fairly easy to perform although the airplane may be blown downstream as much as 3 spans before a trim condition can be established. The distance that the airplane will be blown down-stream can be reduced by restraining the upwind landing gear until the instant of take-off" (p. 1).