A complete technical description of the Clerget heavy-oil engine is presented along with the general characteristics. The general characteristics are: 9 cylinders, bore 120 mm, stroke 130 mm, four-stroke cycle engine, rated power limited to 100 hp at 1800 rpm; weight 228 kg; propeller with direct drive and air cooling. Moving parts, engine block, and lubrication are all presented.

This report provides a summary of the important steps to be taken in combating airplane fires. Some considerations and ways of preventing fires from developing are provided.

We first undertook experiments with air, devoted principally to the investigation of the disturbances due to the differences in the nature of the flow to the nozzle. The difficulty of measuring the air, however, caused us to experiment with water. Due to the possibility of measuring the capacity of the container, this method was much more accurate than measuring with Pitot tobes.

It was learned that the law of resistance for high R values does not follow the simple powers, and that the powers, which can be obtained approximately for the velocity distribution, gradually change. Since, moreover, very important investigations have recently been made on the resistance of plates at very high R values, it seemed of interest to apply the above line of reasoning to the new general law of resistance. For this purpose, the resistance and velocity distribution along the plate must always be equal to the values of the pipe flow at the corresponding Reynolds number.

In the present study it is proposed to provide an equipment permitting the study of the propagation of the region of reaction in mixtures of air and carbureted gases enclosed within a cylinder. Ignition is produced at the end of compression by an electric spark. With this apparatus it is proposed to determine: 1) the influence of the richness of the explosive mixture on the rate of flame propagation; 2) the influence of the degree of volumetric compression on one of the hydrocarbons; 3) the influence of the variation of initial temperature of the mixture before compression; 4) the influence of tetraethyl-lead on the propagation - notably on the formation of the explosive wave.

The nature of turbulent flow through pipes and around obstacles is analyzed and illustrated by photographs of turbulence on screens and straighteners. It is shown that the reversal of flow and of the resistance law on spheres is not explainable by Prandtl's turbulence in the boundary layer. The investigation of the analogous phenomena on the cylinder yields a reversal of the total field of flow.

"Measurement of perpendicular impacts of a landing gear with different shock-absorbing struts against the drum testing stand. Tests were made with pneumatic shock absorbers having various degrees of damping, liquid shock absorbers, steel-spring shock absorbers and rigid struts. Falling tests and rolling tests. Maximum impact and gradual reduction of the impacts in number and time in the falling tests. Maximum impact and number of weaker impacts in rolling tests" (p. 1).

Memorandum presenting a description of the Dornier seaplane Do X. Details of the general description, materials, details of the main wing and upper wing, details of the hull and of the wing stubs, tail surfaces and control lines, power plant, and launching car and floating dock are provided.

Memorandum presenting the experimental results of tests to confirm the contribution to the study of normal burning in gaseous carbureted mixtures.

The icing hazard can, in most cases, be avoided by correct execution of the flights according to meteorological viewpoints and by meteorologically correct navigation (horizontal and, above all, vertical). The zones of icing hazard are usually narrowly confined. Their location can be ascertained with, in most cases, sufficient accuracy before take-off.

A general description of the small DVL wind tunnel is provided, with emphasis on air conduction, blower and velocity regulation, velocity measurement, and balance and model suspension.

From Summary: "The purpose of this report is to make the complicated processes on the direct-lift propeller amenable to analysis and observation. This is accomplished by placing the physical phenomena, starting with the most elementary process, in the foreground, while limiting the mathematical treatment to the most essential in view of the fundamental defects of the theorems. Comparison with model experiments supplements and corroborates the theoretical results."

The viewpoints are discussed, according to which the scavenging of two-stroke-cycle engines can be evaluated, and the relations between scavenging pressure and the quantity of the scavenging medium required, as also between the scavenging pressure and the revolution speed, are developed. It is further shown that the power increase is limited by the scavenging process, so that further researches are desirable for qualitative improvement. These results lead to several conclusions regarding the propulsion of motor vehicles by the two-stroke-cycle engines.

"This report presents a survey of previous theoretical and experimental investigations on wing flutter covering thirteen cases of flutter observed on airplanes. The direct cause of flutter is, in the majority of cases, attributable to (mass-) unbalanced ailerons. Under the conservative assumption that the flutter with the phase angle most favorable for excitation occurs only in two degrees of freedom, the lowest critical speed can be estimated from the data obtained on the oscillation bench" (p. 1).

The present report is a comparison of the experimentally defined temperature and heat output of cooling fins in the air stream with theory. The agreement is close on the basis of a mean coefficient of heat transfer with respect to the total surface. A relationship is established between the mean coefficient of heat transfer, the dimensions of the fin arrangement, and the air velocity.

The performance of a glider is determined by means of the velocity polar, which represents the connection between horizontal and sinking speed. The mean sinking speed for a given speed range can be determined on the basis of the velocity polar. These data form the basis for the most propitious design of a performance-type glider with a view to long-distance flight.

"A survey of the possibilities of gliding in convection currents reveals that heretofore only the most simple kind of ascending convection currents, that is, the "thermic" of insolation, has been utilized to any extent. With the increasing experience in gliding, the utilization of the peculiar nature of the "wind thermic" and increased glider speed promises further advances. Evening, ocean, and height "thermic" are still in the exploration stage, and therefore not amenable to survey in their effects" (p. 1).

"The static stresses of airplane parts, the magnitude of which can be determined with the aid of static load assumptions, are mostly superposed by dynamic stresses, the magnitude of which has been but little explored. The object of the present investigation is to show how the strength of airplane parts can best be tested with respect to dynamic stresses with and without superposed static loading, and to what extent the dynamic strength of the parts depends on their structural design. Experimental apparatus and evaluation methods were developed and tried for the execution of vibration-strength tests with entire structural parts both with and without superposed static loading" (p. 1).

This report describes a device for arbitrary enlargement of the gliding angle of airplanes, especially of such with flat gliding angle and difficult landing characteristics. The D.V.L. gliding angle control (design, Hubner) permits a local interruption of the lift distribution along the span and consequently an increased induced drag. The mechanism comprises two wing rudders operated by lever from the pilot's cockpit. Said rudders are fitted on the top side of the wing near the leading edge. The displacement of these rudders results in a separation of the air flow on the top side of the wing.

The quantity of air which the disk area described by propeller blades travels through, is accelerated rearward conformably to the momentum of the forces acting on the propeller. The accelerated air mass forms behind the propeller the so-called slipstream, in which among others, the mean velocity of advance is increased. If the propeller axis slopes toward the relative flight direction, the slipstream direction likewise changes, i.e., it sets up a downwash behind the propeller.

"Three general theories treating the potential flow about an arbitrary wing section are discussed in this report. The first theory treats the method of conformal transformation as laid down by Theodorsen and Garrick; the second is a generalization of Birnbaum's theory for moderately thick airfoils; the third is a general investigation of the complex velocity function with particular reference to the relations first discussed by F. Weinig. The relative merits of the different methods in question are illustrated on a worked-out example and will be published in a subsequent issue of this periodical" (p. 1).

An analysis is made here of the problem of long plates with transverse stiffeners subject to shear. A typical example would be a long Wagner beam. The shear stress is calculated at which the web wrinkles and shear stress becomes a maximum. The equation is solved for both a condition of free support and rigidity of support on the edges.

This report covers a series of tests on thin flat elastic strips restrained at two parallel edges and subjected to shear by conversely directed stresses. Theoretical treatments, particularly those of Lilly, Southwell and Skan, and Timoshenko are briefly outlined. The problem to be solved by these tests was to find out whether, and to what extent the conditions and assumptions upon which the calculations are based are complied with in the tests.

Accurate prediction of gust stress being out of the question because of the multiplicity of the free air movements, the exploration of gust stress is restricted to static method which must be based upon: 1) stress measurements in free flight; 2) check of design specifications of approved type airplanes. With these empirical data the stress must be compared which can be computed for a gust of known intensity and structure. This "maximum gust" then must be so defined as to cover the whole ambit of empiricism and thus serve as prediction for new airplane designs.