The possibility of overshooting the anticipated normal acceleration as a result of the artificial-feel characteristics of the F-89C airplane at a condition of minimum static stability was investigated analytically by means of an electronic simulator. Several methods of improving the stick-force characteristics were studied. It is shown that, due to the lag in build-up of the portion of the stick force introduced by the bobweight, it would be possible for excessive overshoots of normal acceleration to occur in abrupt maneuvers with reasonable assumed control movements. The addition of a transient stick force proportional to pitching acceleration (which leads the normal acceleration) to prevent this occurring would not be practical due to the introduction of an oscillatory mode to the stick-position response. A device to introduce a viscous damping force would Improve the stick-force characteristics so that normal acceleration overshoots would not be likely, and the variation of the maximum stick force in rapid pulse-type maneuvers with duration of the maneuver then would have a favorable trend.

"High-speed wind-tunnel tests were conducted of two versions of a 0.17-scale model of the McDonnell XF2H-1 airplane to ascertain the high-speed stability and control characteristics and to study means for raising the high-speed buffet limit of the airplane, The results for the revised model, employing a thinner wing and tail than the original model, revealed a mild diving tendency from 0.75 to 0.80 Mach number, followed by a marked climbing tendency from 0.80 to 0.875 Mach number. The high-speed climbing tendency was caused principally by the pitching-moment characteristics of the wing" (p. 1).

Report presenting an investigation of the effects of many of the parameters significant to wing flutter on several untwisted rotating models to determine their significance with respect to stall flutter of propeller blades. The parameters included torsional stiffness, section thickness ratio, sweepback, length-chord ratio, section center-of-gravity location, blade taper, Mach number, and fluid density. Results regarding the considerations on method of presentation, experimental data and discussion, some possible applications, and a comparison of experiment with classical-flutter theory are provided.

The zero-lift damping in roll of the Bell MX-776 missile has been measured by a sting-mounted rocket-model technique at Mach numbers from 0.6 to 1.56. The damping-in-roll data, in general, show no unusual variation with Mach number. Aileron rolling-moment effectiveness derived from these data and previously obtained rolling-effectiveness data appear reasonable,.

Report presenting an investigation to determine the longitudinal stability and afterbody pressure characteristics of the TX-14 and TX-16 special weapons at transonic and supersonic speeds. Results regarding dynamic testing and pressure testing are provided.

Report presenting a series of fence installations tested on a swept-wing jet airplane to determine their effects on the longitudinal instability, or "pitch-up", encountered in high-maneuvering flight. Longitudinal-stability measurements were made at a variety of Mach numbers with nine fence configurations that varied in chordwise extent and spanwise position. Results regarding longitudinal stability, flow phenomena, buffeting and wing dropping, drag, and low-speed stalls are provided.

Report presenting the heat transfer and pressures on the lifting surfaces of a 60 degree delta wing with NACA 65A005 profile at angles of attack up to 9 degrees. Results obtained are compared to values obtained from flat-plate theory.

Models were tested to evaluate effects of Reynolds number for both laminar and turbulent boundary layers. Principal geometric variables investigated were afterbody shape and length-diameter ratio. Force tests and base-pressure measurements were made. Schlieren photographs were used to analyze the effects of viscosity on flow separation and shock-wave configuration and to verify the condition of the boundary layer as deduced from the force tests. The results are discussed and compared with theoretical calculations.

Report presenting an experimental investigation of the pressure distributions on a hemispherical nose 3.98 inches in diameter, mounted on a cylindrical support, at several Mach and Reynolds numbers. The Reynolds number was based on body diameter and free-stream conditions. Pressure-drag coefficients were calculated and good agreement was obtained with other testing.

"The National Advisory Committee for Aeronautics has conducted a flight test of a model approximating the McDonnell F3H-1N airplane configuration to determine its pitch-up and buffet boundaries, as well as the usual longitudinal stability derivatives obtainable from the pulsed- tail technique. The test was conducted by the freely flying rocket-boosted model technique developed at the Langley Laboratory; results were obtained at Mach numbers from 0.40 to 1.27 at corresponding Reynolds numbers of 2.6 x 10(exp 6) and 9.0 x 10(exp 6). The phenomena of pitch-up, buffet, and maximum lift were encountered at Mach numbers between 0.42 and 0.85" (p. 1).

Report presenting an investigation to determine the aerodynamic characteristics of two three-blade propellers over a range of blade angles and Mach numbers. The thick-blade propeller was more adversely affected by compressibility than the thin-blade propeller, and the maximum efficiency of the thin-blade propeller was higher than the thick-blade propeller.

From Summary: "A review of the status of the knowledge on turbine-blade cooling and a description of pertinent NACA investigations are presented. The current limitations in performance of uncooled and cooled engines are briefly discussed. Finally, the knowledge available and investigations to increase the knowledge on heat transfer, cooling-flow, and performance characteristics of cooled turbines are discussed."

Report presenting supersonic-tunnel tests of two models of similar supersonic airplane configurations at Mach numbers of 1.55, 1.90, and 2.32 to determine values of the drag, lift, pitching moment, yawing moment, and side force. The models were similar except for the vertical wing location relative to the body axis and horizontal tail; one had a high wing and one had a low wing. Results regarding the precision of data, Reynolds numbers of tests, results at the different Mach numbers, and Schileren photographs are provided.

The performance of NACA 65-series compressor blade section in cascade has been investigated systematically in a low-speed cascade tunnel. Porous test-section side walls and for high-pressure-rise conditions, porous flexible end walls were employed to establish conditions closely simulating two-dimensional flow. Blade sections of design lift coefficients from 0 to 2.7 were tested over the usable angle-of-attack range for various combinations of inlet-flow angle. A sufficient number of combinations were tested to permit interpolation and extrapolation of the data to all conditions within the usual range of application. The results of this investigation indicate a continuous variation of blade-section performance as the major cascade parameters, blade camber, inlet angle, and solidity were varied over the test range. Summary curves of the results have been prepared to enable compressor designers to select the proper blade camber and angle of attack when the compressor velocity diagram and desired solidity have been determined.

Memorandum presenting the Bell X-5 variable-sweep research airplane tested primarily at 58.7 degrees sweepback to determine the characteristics at transonic speeds of a fighter-type airplane with extreme sweepback. Some of the dynamic and static lateral stability characteristics have been discussed previously. Results regarding the lateral control, roll coupling, lateral problems at high lift, wing dropping, rudder oscillation at supersonic Mach numbers, and some pilots' impressions are also provided.

A preliminary analytical evaluation of the air and fuel specific-impulse characteristics of hydrogen, a-methylnapthalene, and graphite carbon has been made. Adiabatic constant-pressure combustion flame temperatures for each fuel at several equivalence ratios were calculated for an initial air temperature of 560 degrees R and a pressure of 2 atmospheres.

Memorandum presenting forces and moments measured at Mach number 1.6 in the 4- by 4-foot supersonic pressure tunnel on bombs of fineness ratios 7.0 and 10.5 in the presence of a swept-wing fighter-bomber airplane configuration for a large number of positions under the fuselage. The results can be used to calculate bomb-drop paths.

"An investigation to determine the performance and operational characteristics of the TG-1OOA gas turbine-propeller engine was conducted in the Cleveland altitude wind tunnel. As part of this investigation, the combustion-chamber performance was determined at pressure altitudes from 5000 to 35,000 feet, compressor-inlet rm-pressure ratios of 1.00 and 1.09, and engine speeds from 8000 to 13,000 rpm. Combustion-chamber performance is presented as a function of corrected engine speed and corrected horsepower" (p. 1).

"An experimental investigation, using microscopic observation and color motion photomicrographs of the action, was conducted to determine the cause of fretting. Glass and other noncorrosive materials, as well as metals, were used as specimens. A very simple apparatus vibrated convex surfaces in contact with stationary flat surfaces at frequencies of 120 cycles or less than l cycle per second, an amplitude of 0.0001 inch, and load of 0.2 pound" (p. 135).

Report presenting an investigation to determine the effect of oxygen concentration of the inlet oxygen-nitrogen mixture on the combustion efficiency of a J33 single combustor operating with gaseous propane fuel. Combustion efficiency data were obtained at a variety of combustion-inlet total pressures, fuel flow rates, and inlet oxygen concentrations. Results regarding combustor data, application of fundamental combustion properties to combustor data, application of simplified reaction kinetics equation to combustor data, comparison of liquid and gaseous fuel data, and limitations of correlation parameters.

"Free-flight tests have been made to determine the drag at zero lift of several configurations of a missile having triangular wings and tails. Base-pressure measurements were also obtained for some of the configurations. The results show that increasing the wing thickness ratio from 4 to 6 percent increased the wing drag by about 100 percent at M = 1.3 and by about 30 percent at M = 1.8" (p. 1).

Report summarizing research on the strength and creep of aircraft structural elements and components at elevated temperatures. Experimental data for aluminum alloy columns, plates, stiffened panels, and multiweb box beams are presented for temperatures up to 600 degrees Fahrenheit and compared with results predicted from materials data.

Report presenting an investigation at transonic speeds to determine the effects of fences, drooped nose, combination fences and drooped nose, and vortex generators on a 45 degree sweptback wing-fuselage combination. The purpose of undertaking this investigation was due to the pitch-up tendency that results from leading-edge vortex-type flow on thin sweptback wings. The data for each component and their interaction with one another is also provided.

An investigation of forced-convection heat transfer and associated pressure drops was conducted with air flowing through smooth tubes for an over-all range of surface temperature from 535 degrees to 3050 degrees r, inlet-air temperature from 535 degrees to 1500 degrees r, Reynolds number up to 500,000, exit Mach number up to 1, heat flux up to 150,000 btu per hour per square foot, length-diameter ratio from 30 to 120, and three entrance configurations. Most of the data are for heat addition to the air; a few results are included for cooling of the air. The over-all range of surface-to-air temperature ratio was from 0.46 to 3.5.